The application and detail drawings in this manual are strictly for illustration purposes and may not be applicable to all building designs or product installations. Projects should conform to local building codes. Central States Manufacturing is not responsible for the performance of the material if it is not installed correctly.
This manual contains suggestions and guidelines on each project’s conditions. It is the buyer’s responsibility how to erect your Centra Series building. The drawings to verify all applicable code requirements, check all in this guide are for illustration purposes only and...
CARE AND HANDLING STAGE HANDLING Galvalume® steel sheets have a good service life when When unloading panels, extreme caution must be exposed to normal weather conditions however, to employed. Care needs to be used when unloading protect the appearance of panels and trims from panels with a forklift.
ACCESSORIES PARTS LIST ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY NOTE ACC50 RLCLINGLUE Inside Closure ACC51 Butyl Tape ACC52 MRS10CLEAR Clear Sealant Tube ACC53 GRAYFLEX115 Expandable Foam Roll DOOR47 3070DOOR Commercial Walk Door Steel door leaf only DOOR48 8X3070JAMB Jamb Kit for Walk Door Include jambs, header, threshold, door lever...
Page 7
FASTENERS PARTS LIST ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY NOTE FAST3 114(color)MM Metal Screws in Roof color 1,000 FAST12 114(color)MM Metal Screws in Wall color 1,000 FAST4 78(color)LAP Lap Screws in Roof color May have additional FAST13 78(color)LAP Lap Screws in Wall color bags of 78LAP in multiple trim colors.
Page 9
PLATES PARTS LIST ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY LENGTH PLATE35 GIRTCLIP Girtclip PLATE41 RFPEAK Rigid Frame Peak Plate PLATE42 RFHAUNCH Rigid Frame Haunch Plate PLATE43 RFBASE Rigid Frame Base Plate PLATE44 EWPEAK Peak Plate for Endwall Frame PLATE45 RFSPACER Spacer Plate...
Page 10
TRIM PARTS LIST ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY LENGTH TRIM2 RLFRC36 Ridge Cap Panels for Roof 18 TRIM14 Eavetrim 14' 2" TRIM16 Ratguard Trim 14' 2" TRIM30 Ratguard Trim 16' 2" TRIM18 REND Rake Trim End Cap TRIM19 PBOXFGRAPHIC Peak Box Trim...
Page 11
TRIM PARTS LIST ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY LENGTH TRIM21 Outside Corner Trim 10' 2" TRIM22 Head Trim 10' 3" TRIM26 Head Trim 3' 6" TRIM23 Jamb Trim 10' 2" TRIM27 Jamb Trim 7' 2" TRIM24 Jamb Header Trim 10' 2"...
THIS SECTION IS INTENDED FOR YOUR CONCRETE FOUNDATION SPECIALIST C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 15
THIS SECTION IS INTENDED FOR YOUR CONCRETE FOUNDATION SPECIALIST Dia = 1/2" STEEL LINE 3" PROJ 4" 8" 2" " 8" ANCHOR BOLT PROJECTION Detail A Dia = 1/2" 1. The metal building manufacturer is responsible for the 3" design of the anchor bolt diameter only to permit the transfer of forces between the base plate and the anchor bolt in shear, bearing and tension, but is not responsible for the anchor bolt embedment for transfer of forces to the foundation.
PROJECT OVERVIEW Completed Structure The above drawing shows the completed frame structure and columns labeled. The columns will be called out periodically throughout the instructions. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 17
PROJECT OVERVIEW Completed Structure The following instructions are to assemble the 30x52x10 building as shown above. There will be optional variations to the buildings layout called out on certain pages. Follow those instructions as they pertain to your needs. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
STEP 1 Note: To ensure building is square, do not fully tighten REQUIRED PARTS bolts until after STEP29. (12) PURLIN25 (6) PLATE43 (6) PLATE45 PLATE42 (6) PLATE42 (24) PLATE35 (96) FAST54 PURLIN25 PLATE45 PLATE35 PLATE43 DIRECTIONS Assemble Columns A ,F, G, H, M and N Note: Place level on all girt clips throughout installation to ensure level girts.
Page 19
STEP 2 REQUIRED PARTS (2) PURLIN27 (10) PLATE35 (16) FAST54 PURLIN27 PLATE35 PLATE35 DIRECTIONS Assemble Columns B and E 1. Layout (1) PURLIN27 corner column for column B. 2. Attach (1) PLATE35 at bottom using FAST54. 3. Attach (2) PLATE35 at 3'6" using FAST54. 4.
Page 20
STEP 3 If you are adding a framed opening to the endwall. Refer to page 69 for assembly instructions. REQUIRED PARTS (2) PURLIN16 (10) PLATE35 (16) FAST54 PLATE35 PURLIN16 DIRECTIONS Assemble Columns C and D 1. Layout (1) PURLIN16 corner column for column C. 2.
Page 21
STEP 4 DIRECTIONS Stand and Anchor Columns A, B, C, D, E, F, G, and, N Note: Anchor bolts and nuts are not included in building package. Anchor bolts are placed by your foundation specialist when laying foundation and corresponding nuts will be provided by your foundation specialist. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 22
STEP 5 REQUIRED PARTS (2)PURLIN32 (4) PURLIN23 (32) FAST54 PURLIN23 PURLIN32 DIRECTIONS Attaching Zee Girts Note: Do not overtighten bolts on wall girts until columns are vertically level. Then tighten bolts. This applies throughout installation. 1. Attach PURLIN23 between columns B & C and D & E as shown. 2.
Page 23
STEP 6 REQUIRED PARTS (8) PURLIN22 (20) FAST54 PURLIN22 DIRECTIONS Attaching Zee Girts Attach PURLIN22 between columns B & A, A & N, E & F, and F & G using FAST54 as shown. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 24
STEP 7 REQUIRED PARTS (1) PURLIN27 (5) PLATE35 (8) FAST54 PLATE35 PLATE35 PURLIN27 PURLIN27 DIRECTIONS Assemble Column I 1. Layout (1) PURLIN27 column for column I. 2. Attach (1) PLATE35 at bottom using FAST54. 3. Attach (2) PLATE35 at 3'6" from bottom using FAST54. 4.
Page 25
STEP 8 REQUIRED PARTS (1) PURLIN27 (4) PLATE35 (8) FAST54 PLATE35 PLATE35 PURLIN27 PURLIN27 DIRECTIONS Assemble Column L 1. Layout (1) PURLIN27 column for column L. 2. Attach (1) PLATE35 at bottom using FAST54. 3. Attach (1) PLATE35 at 3'6" from bottom using FAST54. 4.
Page 26
STEP 9 If you are not adding a garage door opening. Refer to page 68 for assembly instructions. REQUIRED PARTS (1) PURLIN16 (4) PLATE35 FAST54 Note: Adjust the top PLATE35 FAST46 location to accommodate the FAST54 door height. PLATE35 PURLIN16 FAST46 DIRECTIONS Assemble Column J...
Page 27
STEP 10 REQUIRED PARTS (1) PURLIN16 (3) PLATE35 FAST54 FAST46 FAST54 PLATE35 FAST46 PURLIN16 DIRECTIONS Assemble Column K Note: Adjust the top GIRTCLIP location to accommodate the door height. 1. Layout (1) PURLIN16 column for column K. 2. Attach (1) PLATE35 at bottom using FAST46. 3.
Page 28
STEP 11 STEP 11 DIRECTIONS Stand and Anchor Columns H, I J, K, L and M Note: Anchor bolts and nuts are not included in building package. Anchor bolts are placed by your foundation specialist when laying foundation and corresponding nuts will be provided by foundation specialist. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 29
STEP 12 REQUIRED PARTS (3) PURLIN23 (16) FAST54 PURLIN23 DIRECTIONS Attaching Zee Girts 1. At 3'6" and 7'4" from bottom of column, attach PURLIN23 between columns I and J using FAST54 as shown. 2. At 7'4" from bottom of column. Attach PURLIN23 between columns K and L using FAST54 as shown. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 30
STEP 13 REQUIRED PARTS (8) PURLIN22 (1) PURLIN34 (40) FAST54 (8) FAST46 PURLIN34 PURLIN22 DIRECTIONS Attaching Zee Girts 1. Attach PURLIN22 at 3'6" and 7'4" from the between columns G & H, H&I, L&M and M & L as shown. Use FAST54 to fasten to girtclips.
Page 31
STEP 14 DIY Alternate Method: If lifting machinery is not being used, REQUIRED PARTS assemble center rafters, but do not (12) PURLIN14 PLATE41 attach PLATE41 until STEP 15. (3) PLATE41 (18) PLATE45 (84) FAST54 PURLIN14 PLATE45 DIRECTIONS Assemble Center Rafters 1.
Page 32
STEP 15 DIY Alternate Method: If lifting machinery is not being used, stand center rafters REQUIRED PARTS and hold in place with 2x4 bracing. Then lift and install PLATE41. (48) FAST54 See instructional video for visualization. DIRECTIONS Stand and Install Center Rafters Note: This step will require lifting machinery due to height and weight of components.
Page 33
STEP 16 PLATE44 REQUIRED PARTS (2) PURLIN14 (2) PLATE44 (4) FAST54 PURLIN14 PURLIN14 PURLIN14 DIRECTIONS Assemble Endwall Rafters 1. Attach (1) PLATE44 to (1) PURLIN14 using FAST54. 2. Repeat for the 2nd endwall rafter. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 34
STEP 17 REQUIRED PARTS (2) PURLIN14 (8) FAST54 DIRECTIONS Assemble and Install Endwall Rafters Note: Keep PLATE44 facing interior of building. 1. Attach assembly from previous step to the top of columns K and L using FAST54. 2. Repeat this installation over columns D and E. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 35
STEP 18 REQUIRED PARTS (2) PURLIN14 (6) FAST54 PURLIN14 DIRECTIONS Assemble and Install Endwall Rafters 1. Attach (1) PURLIN14 to the top of columns J and I and attach to installed PLATE44 using FAST54. 2. Repeat this installation over columns D and E. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 36
STEP 19 Note: Base angle is installed to protect the panel edge from concrete corrosion. REQUIRED PARTS (8) PURLIN6 (1) PURLIN37 PURLIN39 each corner (4) PURLIN9 (4) PURLIN39 FAST55 PURLIN9 PURLIN37 PURLIN6 PURLIN9 PURLIN6 PURLIN6 PURLIN9 PURLIN6 PURLIN9 DIRECTIONS Install Base Angle Note: When using the FAST55, you will need to predrill 1.25"...
Page 37
STEP 20 REQUIRED PARTS (3) TRIM24 FAST13 TRIM24 JAMB HEADER TRIM NOTE: Leave 1/8" above concrete, this helps prevent future rust. INTERIOR VIEW INTERIOR VIEW DIRECTIONS Trim Framed Opening 1. Install TRIM24 along columns K and J. Cut length to fi t between fl oor and wall girt at top of framed opening. Fasten to column with FAST13 every 24".
Page 38
STEP 21 REQUIRED PARTS (1) DOOR47 (1) DOOR48 FAST12 FAST55 DIRECTIONS Option 1: Installing walk door in location shown above Note: Determine where you would like to install your walk door. Illustration above shows walk door between columns K and L, but door can be located in any location. 1.
Page 39
STEP 21 CONT. REQUIRED PARTS REQUIRED PARTS (1) DOOR47 (1) DOOR47 (1) DOOR48 (1) DOOR48 (1) FAST12 (1) FAST12 (1) FAST55 (1) FAST55 DIRECTIONS Option 2: Installing door into an alternate location 1. Remove the zee at 3'6" height previously installed in the bay you wish to install your walk door. 2.
Page 40
STEP 22 REQUIRED PARTS (1) TRIM26 (2) TRIM27 FAST24 TRIM22 HEAD TRIM TRIM23 JAMB TRIM DIRECTIONS Trim Framed Opening 1. Install TRIM23 along columns I and J, with the mouth of trim facing outward as shown. Fasten to exterior side of the building with FAST24 every 24".
Page 41
STEP 23 REQUIRED PARTS TRIM15 TRIM16 TRIM30 FAST24 Note: Base of rat guard trim should be below the top of the concrete foundation. BASE ANGLE TRIM16 RAT GUARD RAT GUARD CONCRETE FOUNDATION DIRECTIONS Install Ratguard Trim Note: In this step, you will be installing the trim along the bottom of the building. This trim is available in lengths of 14'2"...
Page 42
STEP 24 REQUIRED PARTS (1) PURLIN13 (4) FAST54 PURLIN13 DIRECTIONS Install Eavestruts Bolt PURLIN13 on top of column H and I using FAST54 as shown above. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 43
STEP 25 REQUIRED PARTS (3) PURLIN13 PURLIN13 (4) PURLIN12 (12) FAST54 PURLIN12 PURLIN12 PURLIN13 DIRECTIONS Install Eavestruts Repeat previous step between Columns B & L, and Columns E & H. The middle bays will use PURLIN12. The outside bays will use PURLIN13. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 44
STEP 26 REQUIRED PARTS (1) PURLIN21 (2) FAST54 PURLIN21 DIRECTIONS Install Roof Purlins Note: The bolt along the center rafter is temporary.(Do not over tighten) Install PURLIN21 between endwall rafter and center using FAST54 as shown above. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 45
STEP 27 REQUIRED PARTS (2) PURLIN19 (1) PURLIN21 (10) FAST54 PURLIN19 STEP 2 PURLIN19 PURLIN21 STEP 1 DIRECTIONS Install Roof Purlins Note: Remove the bolt from the center rafter before installing PURLIN19. 1. Overlap two PURLIN19 and fasten to center rafters as shown in STEP 1. 2.
Page 46
STEP 28 REQUIRED PARTS (1) PURLIN21 (7) FAST54 PURLIN19 PURLIN21 DIRECTIONS Install Roof Purlins Install PURLIN21 over end rafter as shown C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 47
STEP 29 REQUIRED PARTS (14) PURLIN21 PURLIN21 (14)PURLIN19 (80) FAST54 PURLIN19 PURLIN19 PURLIN21 DIRECTIONS Install Roof PURLINS Repeat steps 26-28 to install the remaining roof PURLINS. NOTE: After completing STEP29, ensure that building is square by placing a strap on each corner and ratcheting corner columns until they are level.
Page 48
STEP 30 REQUIRED PARTS (4) PURLIN4 FAST24 PURLIN4 DIRECTIONS Install Rake Angle Install PURLIN4 above endwall rafter using FAST24 as shown above. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
Page 49
STEP 31 If you have the wainscot option, please refer to page 64 for assembly instructions. REQUIRED PARTS (1) PANEL11 Note: Install Top & FAST12 Bottom fastener line fi rst before securing middle of panel. PANEL11 CAUTION WALL PANEL To prevent rust, BASE ANGLE leave a 1/8"...
Page 50
STEP 32 REQUIRED PARTS (17) PANEL11 FAST12 FAST13 PANEL11 Note: Use FAST12 to attach the panels to the girts. Use FAST13 when the panels overlap. Top & Bottom Middle FAST13 FAST13 DIRECTIONS Install Wall Sheeting Also, some panels may be overlapped more than 1 rib to avoid cutting. If necessary, panel may be cut long ways at ending edge of sidewall.
Page 51
STEP 33 REQUIRED PARTS (10) PANEL11 FAST12 FAST13 PANEL11 DIRECTIONS Install Wall Sheeting Also, some panels may be overlapped more than 1 rib to avoid cutting. If necessary, panel may be cut long ways at ending edge of sidewall. 1. Repeat STEP 31 and 32 for the other sidewall. 2.
Page 52
STEP 34 REQUIRED PARTS (2) PANEL4 (2) PANEL6 (2) PANEL8 (2) PANEL10 (2) PANEL12 FAST12 FAST13 PANEL4 PANEL4 PANEL12 PANEL12 PANEL6 PANEL6 PANEL8 PANEL8 PANEL10 PANEL10 DIRECTIONS Install Wall Sheeting Also, some panels may be overlapped more than 1 rib to avoid cutting. If necessary, panel may be cut long ways at ending edge of sidewall.
Page 53
STEP 35 REQUIRED PARTS (2) PANEL4 (2) PANEL6 (2) PANEL8 (2) PANEL10 (2) PANEL12 FAST12 FAST13 PANEL4 PANEL4 PANEL12 PANEL12 PANEL6 PANEL6 PANEL8 PANEL8 PANEL10 PANEL10 DIRECTIONS Install Remaining Wall Panels Also, some panels may be overlapped more than 1 rib to avoid cutting. If necessary, panel may be cut long ways at ending edge of sidewall.
Page 54
STEP 36 REQUIRED PARTS (4) TRIM21 FAST23 TRIM21 OUTSIDE CORNER TRIM21 COLUMN TYPE AND ORIENTATION MAY VARY WALL PANEL PURLIN DIRECTIONS Install TRIM21 Install all 4 TRIM21 with FAST23 along the corners of the wall panels. Place fasteners to match fastener line on wall panels (do not overtighten).
Page 55
STEP 37 REQUIRED PARTS (4) TRIM14 FAST12 ACC50 TRIM14 EAVE TRIM ACC50 INSIDE CLOSURE TRIM14 WALL PANEL EAVE STRUT DIRECTIONS Install TRIM14 1. Place ACC50 on top of TRIM14 by installing. Line up rib profi le of closure with wall panel rib profi le. Place on edge of top leg of trim.
Page 56
STEP 38 If you are installing gutters, please go to page 70 before proceeding. REQUIRED PARTS Tip: Squareness is key on this fi rst panel. (1) PANEL3 Note: Do not Start by aligning the panel along the rake FAST3 angle. Then measure that each side is fasten top row.
Page 57
STEP 39 PANEL3 REQUIRED PARTS (35) PANEL3 ACC51 FAST4 FAST3 Top & Bottom Middle FAST4 FAST4 DIRECTIONS Finish Sheeting the Roof 1. Use FAST3 to secure panels to the purlins. Use FAST4 when securing the panels together. 2. Do not overlap roof panel more than one rib, if the length of your building is not divisible by 3 then your last panel will need the excess cut off .
Page 58
STEP 40 TRIM2 RIDGE CAP REQUIRED PARTS (18) TRIM2 FAST3 ACC51 TRIM2 Tip: To locate the center of ridge on building, use two levels to meet in ROOF PANEL the middle to determine apex. ZEE PURLIN DIRECTIONS Install the Ridge Cap 1.
Page 59
STEP 41 REQUIRED PARTS (4) TRIM28 (4) TRIM18 FAST23 TRIM18 RAKE TRIM END CAP TRIM28 RAKE TRIM TRIM28 WALL PANEL PURLIN DIRECTIONS Install Rake Trims 1. Install the TRIM28 with TRIM18. TRIM28 may need to be cut to match panel length. Hide cut edge at top of ridge. a.
Page 60
STEP 42 REQUIRED PARTS (2) TRIM19 FAST20 TRIM19 PEAK BOX DIRECTIONS Installing the Peak Box 1. Install each TRIM19 with pop rivets or lap fasteners into the rake trim. (do not overtighten) 2. Remove any excess shaving from the roof panels to ensure shavings are not left behind that might create rust. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 61
STEP 43 ENJOY YOUR COMPLETED BUILDING Your building is fi nished. Take a break, relax, and fi nd a way to payback the friends who helped. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
OPTIONAL PARTS Most options both remove and add parts. The following tables list the parts adjustments that are made with each option. Please refer to images at front of assembly instructions if necessary. ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY LENGTH Wainscot Option The following items are removed...
Page 63
OPTIONAL PARTS ASSEMBLY PART # MANUFACTURER PART # DESCRIPTION QUANTITY LENGTH Gutter Option The following items are added TRIM33 GU142 Gutters 14' 2" TRIM34 DK102 Downspouts 10' 2" TRIM35 Gutter Straps TRIM36 DSS2 Downspout Strap TRIM37 Gutter End Cap TRIM38 Outside Corner Box Remove Endwall Framed Opening Option The following items are removed...
WAINSCOT OPTION REQUIRED PARTS PURLIN48 PURLIN37 PURLIN49 PURLIN37 PURLIN49 FAST54 PURLIN37 PURLIN48 DIRECTIONS Install the PURLINs 1. Install PURLIN48 on the sidewalls. 2. Install PURLIN37 and PURLIN38 on the endwall. 3. Use FAST12 through the 2" side of the angle and aligning the 4" side (pointed up) with the outside steel line of the wall ZEE girt.
Page 66
WAINSCOT OPTION REQUIRED PARTS TRIM39 TRIM32 FAST3 CAUTION PURLIN36 WALL PANEL To prevent rust, leave a 1/8" space TRIM39 between the wainscot TRIM31 WAINSCOT trim and upper TRIM WALL GIRT wall panels. WAINSCOT PANEL DIRECTIONS Install the Wainscot Trim Install the TRIM39 and TRIM32 wainscot trim on to the 3'6" girt, allowing the trim horizontal fl at surface to rest on top of the lower panels installed.
Page 67
WAINSCOT OPTION REQUIRED PARTS PANEL13 FAST54 PANEL13 DIRECTIONS Install Upper Wall Panels 1. Follow Step 32 through step 35 to install wall panels on to the upper section of wall panels. Fasten bottom of panel to PURLIN36/37/38. Follow diagram below. Be sure to leave 1/8" space between wainscot trim and upper wall panels to prevent rusting &...
REMOVE ENDWALL OPENING OPTION DIRECTIONS Remove Framed Opening in Endwall Option 1. When assembling columns J and K in step 11 and 12, use all FAST54, rather than a mixture of FAST54 and FAST46. 2. Repeat steps 6-8 to install wall girts similar to other endwall erected in steps 6-8. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C .
Page 69
ADD ENDWALL OPENING OPTION DIRECTIONS Endwall Framed Opening Add Option 1. Assemble columns C and D using steps 11 and 12. do not follow Step 3. 2. Install opening header between columns C & D using step 14. C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 •...
GUTTERS OPTION ROOF PANEL CLOSURE GUTTER STRAP GUTTER EAVE STRUT WALL PANEL TRIM14 Tip: If multiple gutter sections are required to meet the building's length, then sequential gutter(s) will nest inside of the previous gutter's end approximately 4" with a small bead of sealant (ACC52). Fasten the sequential gutter to the previous gutter using POP or 78LAP fasteners then continue until you have fully covered the length of your building, trimming any excess gutter to allow the fi nal gutter end to align with the endwall steel line.
Page 71
GUTTERS OPTION DIRECTIONS DIRECTIONS Installing gutters Note: TRIM38 will be need to be installed after Rake trim (TRIM28) is installed in future steps. 5. With gutters now hung, identify the location of downspouts. Downspouts will typically be placed on each end of the building's gutter. The exact location can very (6"-14", but is recommended to position the downspout directly centered over a wall rib, which will allow for a vertical and level downspout once installed.
ADD SIDEWALL OPENING OPTION Note: Optional sidewall opening can only be 10’ wide. PURLIN30 PURLIN43 PURLIN51 PURLIN42 PURLIN51 Sidewall Framed Opening add Option You will have fl exibility to install this opening in any sidewall bay that suits your needs for every sidewall framed opening section.
Page 73
SIDEWALL OPENING OPTION PURLIN30 PURLIN30 PLATE46 PLATE46 PLATE35 PURLIN42 PURLIN42 Figure 1 - for 7' and 8' door height Figure 2 - for 9' door height DIRECTIONS Note: At this point the bases of your jambs are not attached to the concrete. This is fi ne, as the next step will ensure every connection has been done correctly for your framed opening.
Page 74
NOTES C E N T R A L S T A T E S M A N U F A C T U R I N G , I N C . E f f e c t i v e 0 1 / 2 0 2 1 • I n f o r m a t i o n s u b j e c t t o c h a n g e...