Sharp QT-80W Service Manual page 8

Stereo radio cassette recorder
Hide thumbs Also See for QT-80W:
Table of Contents

Advertisement

QT-80W
Step
Alignment
Frequency
1
MW IF: 455 kHz (1) AM IF sweep
(2) Alignment
(3) Power supply
2
MW
(1) MW sweep
TRACKING fH:
1,650 kHz
(2) Alignment
(3) Power supply
3
MW BAND
Same as step 2
COVERAGE fL:
515 kHz
4
Repeat step 2, 3 until no further improvement can be made.
5
MW BAND
Same as step 2
COVERAGE fH:
1,400 kHz
6
MW TRACKING Same as step 2
fL: 600 kHz
7
Repeat step 5, 6 and then step 2, 3, 5,6 until no further improvement can be made.
Step
Alignment
Frequency
1
SW1 BAND
(1) SW1 sweep
COVERAGE fH:
7.4 MHz
(2) Alignment
(3) Power supply
2
SW1 BAND
Same as step 1
COVERAGE fL:
2.25MHz
3
Repeat step 1, 2 until no further improvement can be made.
4
SW1
Same as step 1
TRACKING fH:
6 MHz
5
SW1
Same as step 1
TRACKING fL:
2.6 MHz
6
Repeat step 4, 5 and then step 1, 2, 4, 5 until no further improvement can be made.
Step
Alignment
Frequency
1
SW2 BAND
(1) SW2 sweep
COVERAGE fH:
22.5 MHz
(2) Alignment
(3) Power supply
2
SW2 BAND
Same as step 1
COVERAGE fL:
7.2 MHz
3
Repeat step 1, 2 until no further improvement can be made.
4
SW2
Same as step 1
TRACKING fH:
19 MHz
5
SW2
Same as step 1
TRACKING fL:
8.5 MHz
6
Repeat step 4, 5 and then step 1, 2, 4, 5 until no further improvement can be made.
All manuals and user guides at all-guides.com
MW Section
Test Equipment
Signal-in
Let the MW ANT
generator with
coil close to the
loop antenna
generator ANT.
oscilloscope
Same as step 1
generator with
antenna
oscilloscope
Same as step 1
Same as step 1
Same as step 1
SW1 Section
Test Equipment
Signal-in
Let the MW ANT
generator with
coil close to the
antenna
generator ANT.
point TP1
oscilloscope
Same as step 1
Same as step 1
Same as step 1
SW2 Section
Test Equipment
Signal-in
Inject the RF
generator
signal directly to
point TP1
oscilloscope
Same as step 1
Same as step 1
Same as step 1
Signal-out
Take out the signal Adjust T107 get MAX.
from point TP4
output at 455 kHz
Same as step 1
Adjust P.V.C. (TC3)
get MAX. output at
1,650 kHz
Same as step 1
Adjust T103 to get
MAX. output at 515 kHz end
Same as step 1
Adjust P.V.C. (TC4)
get MAX. output at
1,400 kHz
Same as step 1
Adjust L109 get MAX.
output at 600 kHz
Signal-out
Take out the signal Adjust CT102 get MAX.
from point TP4
output at 7.4 MHz
Same as step 1
Adjust T104 get MAX.
output at 2.25 MHz
Same as step 1
Adjust CT104 get MAX.
output at 6 MHz
Same as step 1
Adjust T101 get MAX.
output at 2.6 MHz
Signal-out
Take out the signal Adjust CT101 get MAX. (1) Band SW in SW2
from point TP4
output at 22.5 MHz
Same as step 1
Adjust T105 get MAX.
output at 7.2 MHz
Same as step 1
Adjust CT103 get MAX.
output at 19 MHz
Same as step 1
Adjust T102 get MAX.
output at 8.5 MHz
– 8 –
Adjust
Remark
(1) Band SW in MW
position
(2) VOL. control in MIN.
position
(3) Tune P.V.C. to
high end
Same as step 1
Tune P.V.C. to low
Tune P.V.C. to
1.400 kHz
Tune P.V.C. to
600 kHz
Adjust
Remark
(1) Band SW in SW1
position
(2) VOL. control in MIN.
position
(3) Tune P.V.C. to
high end
Tune P.V.C. to low
end
Tune P.V.C. to 6 MHz
Tune P.V.C. to
2.6 MHz
Adjust
Remark
position
(2) VOL. control in MIN.
position
(3) Tune P.V.C. to
high end
Tune P.V.C. to low
end
Tune P.V.C. to
19 MHz
Tune P.V.C. to
8.5 MHz

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QT-80W and is the answer not in the manual?

Table of Contents