Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MAKINEX MCP-6-SS
Summary of Contents for MAKINEX MCP-6-SS
- Page 1 Mobile Charge Pod (MCP) MCP-6-SS OPERATOR’S MANUAL Rev 1220...
-
Page 2: Table Of Contents
Table of Contents INTRODUCTION ..............................1 DISCLAIMER ..............................1 ABOUT THIS MANUAL ............................2 SAFETY INFORMATION ............................3 GENERAL SAFETY INFORMATION ........................3 GENERAL SAFETY DECAL ..........................5 PRODUCT SPECIFICATIONS ..........................6 FEATURES ................................. 6 OVERALL PRODUCT DIMENSIONS ......................... 7 MCP SPECIFICATIONS ............................. -
Page 3: Introduction
Thank you for purchasing a MAKINEX product. This manual provides information and procedures to safely operate and maintain the MCP-6-SS Mobile Charge Pod. For your own safety and protection from injury, carefully read, understand, and observe the safety instructions described in this manual. -
Page 4: About This Manual
PROHIBITED These safety warnings do not eliminate all possible hazards that could occur therefore it is essential to use common sense and to strictly follow any instructions to prevent accidents. MCP-6-SS – User Manual Page 2 of 21... -
Page 5: Safety Information
ALWAYS activate the brakes when MCP is in position. NEVER tilt the MCP. NEVER attempt to lift or move the MCP without the assistance of other persons or suitable lifting equipment. MCP-6-SS – User Manual Page 3 of 21... - Page 6 NEVER use water or any other liquids to clean the unit while it is in use. NEVER use any damaged electrical cord sets with the MCP. FIRE -RELATED SAFETY PRECAUTIONS NEVER leave any combustible materials near the MCP. MCP-6-SS – User Manual Page 4 of 21...
-
Page 7: General Safety Decal
GENERAL SAFETY DECAL GEN – 32P – User Manual Page 5 of 27... -
Page 8: Product Specifications
PRODUCT SPECIFICATIONS MCP: OUTLET SOCKETS 6 X Dual 2-Pole 10A Outlets RCBO 16A Type A 30mA 2-Pole SUPPLY LEAD 2.5mm 3-Core Flex Cable with 15A 3-Pin Plug BODY MATERIAL Fire Rated UL 94 V-2 HDPE DRY WEIGHT (kg/lbs) 74/163 BODY DIMENSIONS 1480 x 430 x 1371 (L X D X H) mm (in) Dimensions at rear of locker... -
Page 9: Overall Product Dimensions
OVERALL PRODUCT DIMENSIONS Dimensions in mm MCP SPECIFICATIONS MCP-6-SS – User Manual Page 7 of 21... -
Page 10: Instruction For Use
2. Set the switch on the outlet to the ‘on’ position. SHUTTING DOWN THE MCP 1. Turn all switches on the outlets to the ‘off’ position. 2. Turn the mains switch (if fitted) to the ‘off’ position, otherwise unplug from mains. MCP-6-SS – User Manual Page 8 of 21... -
Page 11: Assembling The Wheels
4. Repeat steps 1-3 for each of the four boltholes on each of the four wheels, ensuring that the matching castors are fastened on the same short end of the body. WASHER SPRING WASHER MCP-6-SS – User Manual Page 9 of 21... -
Page 12: Using The Chain Point
This is to allow the user to secure the MCP in place and prevent it unintentionally moving out of place. MCP-6-SS – User Manual Page 10 of 21... -
Page 13: Wall Mounting
A typical M8 bolt will fit through the holes. Be sure to use the appropriate bolts depending on what surface the unit is being mounted to e.g. masonry, steel, wood fasteners etc., etc. MCP-6-SS – User Manual Page 11 of 21... -
Page 14: Maintenance
MCP as instructed in this manual, including proper storage and appropriate servicing. Should you have questions about replacing components on your MCP, please contact dealer for assistance. MAKINEX dealers have access to all the special tools, technical information, parts and training required to maintain your MAKINEX product in peak operating condition. -
Page 15: General Troubleshooting
Castor wheel is clogged remove if possible Uneven terrain Inspect surface for any obstructions UNIDENTIFIED Contact authorised Makinex dealer for assistance. For other problems or further instructions, contact your authorised Makinex dealer. MCP-6-SS – User Manual Page 13 of 21... -
Page 16: Storage
To keep the MCP in good working order, ensure: 1. Storage is in a dry place, sheltered from the elements of the weather. 2. Between uses, wipe down any surfaces which are especially dirty or covered in foreign debris. MCP-6-SS – User Manual Page 14 of 21... -
Page 17: Limited Warranty
This warranty applies only to new MAKINEX product distributed by us and by our authorised MAKINEX dealers. -
Page 18: Warranty Exclusions
Accessory parts such as starting batteries, fuses, spark plugs, and storage covers. Failures due to acts of God and other force majeure events beyond the manufacturer’s control. Problems caused by parts that are not from the original manufacturer. MCP-6-SS – User Manual Page 16 of 21... -
Page 19: Owner's Responsibility Under Limited Warranty
Manufacturer. It is the responsibility (and cost) of MAKINEX or our appointed agent to return the product to be repaired or replaced under warranty to the consumer- this is valid for domestic territories only (e.g. Australian units will be delivered within Australian territories and European units will be delivered within its designated country’s... -
Page 20: Contact Information
CONTACT INFORMATION For sales, service, warranty and parts for all MAKINEX products; please refer below. SALES, SERVICE, SPARE PARTS & WARRANTY SALES TEL 1300 795 953 or +61 2 9460 8071 WEB www.makinex.com.au AUSTRALIA SERVICE, SPARE PARTS & WARRANTY EMAIL service@makinex.com.au... -
Page 21: Appendices
APPENDICES APPENDIX A – WIRING CIRCUIT DIAGRAM GEN – 32P – User Manual Page 19 of 28... -
Page 22: Appendix B - Risk Assessment
APPENDIX B – RISK ASSESSMENT MCP-6-SS – User Manual Page 20 of 21... - Page 23 MCP-6-SS – User Manual Page 21 of 21...
Need help?
Do you have a question about the MCP-6-SS and is the answer not in the manual?
Questions and answers