Part 3 Setup Options Part 4 ZipVision Pro App Part 5 Wireless to Router Part 6 LAN to PoE Switch Part 7 Wireless to ZIP NVR / DVR Part 8 SD Card Part 9 Fitting Part 10 Alarm Input / Output...
Setting up the RoomWatch is easy using your Zip DVR or NVR interface and once set up the RoomWatch is a fully mobile unit that you can move to wherever suits you without having to reprogram it.
Wireless to Router Wireless to Router Once setup is complete the RoomWatch camera simply be moved about from room to room so you can change what you use it for as the need arises. To connect wiirelessly, you will need:- ·...
Download and install ZipFinder software:- www.softcctv.com/store/Item/Zip-Finder-IP-CCTV-Security-Camera-Discovery-Tool 1. Plug the RoomWatch RJ45 port with a network cable into a PoE switch 2. Using ZipFinder on a Windows Based PC/ Laptop Search and then Tick the SEE040 3. Select Net Mode : DCHP Then click Modify 4.
Instruction Manual Wireless to ZIP NVR / DVR You will need... · Zip NVR / DVR · 12V DC Power Supply · Ethernet network cable · Router 1. Plug the 12V DC into the RoomWatch and the RJ45 port with a network cable into the router 2.
Page 16
Instruction Manual 9. The camera should appear with the IP Address in the bottom table with a green Camera symbol after a few seconds 10. Unplug the RoomWatch from the Router, then pair the RoomWatch with WiFi using the...
SD Card SD Card Different size SD Cards will provide different amounts of recording time, with the Encoding set to the default settings on constant record, the approximate recording time you will get:- The camera can be set to only record when triggered via Motion Detection, PIR or Alarm Inputs to get more recording time.
Fitting Fitting 1. Unscrew camera from mounting bracket and mounting bracket from base plate 2. The mounting bracket will now separate into two parts, base plate and cover. 3. Fix base plate to wall using screws and raw plugs supplied. 4.
Instruction Manual Alarm Input / Output Alarm settings can allow trigger for recording or alarm out. Alarm Input can be selected to NO (Normally Open), NC (Normally Closed) or Off. Alarm Output (Common & Output) can switch a load up to 2A 30V DC.
Firmware Upgrade Firmware Upgrade 12.1 Information Be aware that after applying a new firmware the camera must be reset to factory defaults, this will clear any settings you have made and will require them to be re-entered. The latest firmware for our products are available online .. http://zipdvr.com/firmware.html You should compare your camera's current firmware against those available online as follows : 1.
Instruction Manual Troubleshooting 13.1 Unable to connect to 5G network segment The RoomWatch camera only supports 2.4GHz WiFi, this error will occur if you try and connect to a 5GHz network. Some modern routers that have both 2.4GHz and 5GHz bands use a technique called band steering to intelligently move your devices between the 2.4 GHz and 5 GHz network based on...
Page 27
Troubleshooting 6. Add "5GHz " to the end of the SSID 7. Select Save at the Top 8. Once you have set this, you may need to turn your mobile's WiFi Off then back On. Note - For more detailed information on setting separate bands, then visit the router manufacturer website.
Instruction Manual 13.2 Issues Searching for Device to use with ZipPro If after entering WiFi details in the app (Setup WiFi for the...) if the phone cannot select the RoomWatch then disabling mobile data temporarily can help. During the setup the App connects to the RoomWatch to then connect to the WiFi Network.
Troubleshooting 13.3 ZipFinder Search Not Updating Address of Camera To search for the RoomWatch camera this software needs to be installed and also configured on you Windows PC. If ZipFinder can't get an updated IP address or see the RoomWatch Camera then follow the steps below to allow ZipFinder through Windows Firewall: 1.