Full Gauge MICROSOL II PLUS Quick Start Manual

1- DESCRIPTION

Wall-Link is an interface intended to be used together with Microsol II plus from version 2 and
Microsol II power from version 1. It enables easy and quick remote access to all Microsol II
information and setup.
(1)
Compatible with Microsol II plus or Microsol II power

2 - APPLICATION

Solar heating controlling.

3 - TECHNICAL SPECIFICATIONS

- Power supply: 90 - 264 Vac (50/60 Hz)
- Size: 90 x 131 x 28 mm (W x H x D)
- Operating temperature: 0 to 50°C
- Operating humidity: 10 to 90% RH (no condensation)
- Data communication: by wire - maximum distance of 1000 meters

4 - MAIN SCREEN

The figure below shows the main screen of Wall-Link with the system in operation.
Preferential indication
description
Swimming pool
26.9$C
Preferential indication
value

5 - FUNCTION MENU

The function menu allows configuring Microsol II controller functions remotely. To access the function
menu press and keys simultaneously for two seconds until the functions are shown in the
display. To access any function and confirm the value press
leave any function without confirming press
menu:
01- Access Code 03-Schedule Mode
04-Schedule Evt
02- Functions
5.1 - Access code
The access code 123 must be entered in this screen to enable changing functions of Microsol II
controller. To enter the code press on the message and adjust the value that will be blinking on the
display. Press again to confirm; to cancel and go back press
5.2 - Functions
(1)
In this screen all functions of Microsol II can be adjusted. To make changes press
function and enter the value that will be blinking on the display. Press
value; to cancel and go back press .
Function On Dif Temp
description
dOn@ 10.0 #
Function code Function value
5.3 - Event scheduling mode
(1)
The operating mode of Microsol II event scheduling can be programmed from this screen.

5.4 - Event scheduling

The schedule of the instrument can be viewed and changed by accessing this function with the key
To inform or change the configuration press
week. Adjust the time of beginning and end of the event using the
confirm the new value; to cancel and go back press
To go back or to leave the options press
Monday
Day of week
E02@ 09:40/18:50
Day event Start time

5.5 - Clock adjustment

To adjust the internal clock of Microsol II select this function by pressing (1)
using the and and press to confirm or
To go back or to leave the options press

6 - QUICK ACCESS MENU

The quick access menu allows configuring the setpoints of supports 1 and 2, as well as the manual
operating modes and the overheating temperature for sensor 2. To access this menu, press
while Wall-Link main screen is displayed. To access any function and confirm the value press
REMOTE INTERFACE FOR
MICROSOL II PLUS AND MICROSOL II POWER
Ver.04
(1)
; to go back to the previous menu or to
. The following options are available in the function
05-Clock
.
again to confirm the new
Function unit
on the option corresponding to the event and day of the
and keys, press
.
at any time.
Finish time
. Then adjust the values
to cancel.
at any time.
go back to the previous menu or to leave any function without confirming press
The following options are available in the function menu:
(1)
01-Setpoint A1
02-Setpoint A2
03-S2 Hi Temp
Only with Microsol II plus version 03 or
Only with Microsol II power version 01
6.1- Auxiliary output 1 setpoint
This function allows adjusting the control temperature for auxiliary output 1.
6.2 - Auxiliary output 2 setpoint
This function allows adjusting the control temperature for auxiliary output 2.
6.3 - Sensor 2 overheating temperature
This function allows adjusting the overheating temperature for sensor 2. When applied to swimming
pools this is the limit temperature of the water (comfort temperature)

6.4 - Water pump operating mode

This function allows adjusting the manual operating mode of the water pump.
6.5 - Auxiliary output 1 manual mode enable
The operating mode of the auxiliary 1 output can be toggled between manual and automatic by
pressing
6.6 - Auxiliary output 2 manual mode enable
The operating mode of the auxiliary 2 output can be toggled between manual and automatic by
pressing
03 or Microsol II power from version 01.

6.7 - Viewing the minimum and maximum temperatures

(
only available for
Pressing the
each sensor of Microsol II Power.
7 - ACCESS MENU FOR ADJUSTING THE CONNECTION
Upon accessing the quick access menu while Wall-Link is not connected to Microsol II , the user will
(1)
have two functions available for adjusting the address of the instrumet :
01-McSol 485 Add
7.1 - McSol 485 Add (Microsol II
on the desired
The address of Microsol II controller can be manually adjusted by entering this function. The value of
this function must be the same value configured in Microsol II .
7.2 - Search McSol (Search Microsol II )
on this function makes Wall-Link start searching for Microsol II address automatically.
Pressing
Enter the quick access menu again to stop the automatic search.

8 - SETUP MENU

The operating characteristics of Wall-Link can be adjusted through the setup menu. To access the
function menu press
in the display. The following options are available in the setup menu:
01-McSol 485 Add
02-Interface
.
03-Descriptions
to
8.1 - McSol2 485 Add (Search Microsol II )
This function allows to manually adjusting the address of the Microsol II controller.
The value set for this function should be the same value set on the Microsol II .
8.2 - Interface
Allows adjusting the user interface characteristics:
Fun
I01
Indication
I02
Language (Port, Engl, Esp)
I03
Display contrast
I04
Display timeout
I05
Sound signaling
shortly
; to
04-Pmp Activat
05-A1 Man Mode
06-A2 Man Mode
higher
on this function.
on this function. Note: This option will be only available for Microsol II plus from version
Microsol II power)
key in this function you can browse the minimum and maximum temperatures for
02-Search McSol
(1) address)
(1)
and keys simultaneously for eight seconds until the functions are shown
04-Timeouts
05-Statistics
Description
.
07- Min max Temp
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Min. Max. Unit Default
S1 All - S2
- - - Port
1 10 - 5
0 999 min. 0
Off On - Off