Download Print this page
Full Gauge Wall-Link Manual

Full Gauge Wall-Link Manual

Remote user interface for microsol ii plus

Advertisement

Quick Links

1. DESCRIPTION
Wall-Link
is an interface intended to be used together with Microsol II plus from version 2 and
above.
It enables easy and quick remote access to all Microsol II plus information and setup.
2. APPLICATION
Solar heating controlling.
3. TECHNICAL SPECIFICATIONS
- Power supply: 90 - 264 Vac (50/60 Hz)
- Size: 90 x 131 x 28 mm (W x H x D)
- Operating temperature: 0 to 50°C
- Operating humidity: 10 to 90% RH (no condensation)
- Data communication: by wire - maximum distance of 1000 meters
4. MAIN SCREEN
The figure below shows the main screen of
Wall-Link
Preferential indication
description
Swimming pool
26.9$C
Preferential indication
value
5. FUNCTION MENU
The function menu allows configuring Microsol II plus controller functions remotely. To access the
function menu press
and
keys simultaneously for two seconds until the functions are shown
in the display. To access any function and confirm the value press
menu or to leave any function without confirming press
function menu:
03-Schedule Mode
01- Access Code
02- Functions
04-Schedule Evt
5.1 Access code
The access code 123 must be entered in this screen to enable changing functions of Microsol II plus
controller. To enter the code press
on the message and adjust the value that will be blinking on the
display. Press
again to confirm; to cancel and go back press
5.2 Functions
In this screen all functions of Microsol II plus can be adjusted. To make changes press
desired function and enter the value that will be blinking on the display. Press
new value; to cancel and go back press
Function
On Dif Temp
description
dOn@ 10.0 #
Function code
Function value
5.3 Event scheduling mode
The operating mode of Microsol II plus event scheduling can be programmed from this screen.
5.4 Event scheduling
The schedule of the remote instrument can be viewed and changed by accessing this function with the
key
. To inform or change the configuration press
and day of the week. Adjust the time of beginning and end of the event using the
press
to confirm the new value; to cancel and go back press
To go back or to leave the options press
Day of week
Monday
E02@ 09:40/18:50
Day event
Start time
5.5 Clock adjustment
To adjust the internal clock of Microsol II plus select this function by pressing
values using the
and
and press
To go back or to leave the options press
6. QUICK ACCESS MENU
The quick access menu allows configuring the setpoints of supports 1 and 2, as well as the manual
operating modes and the overheating temperature for sensor 1. To access this menu, press
while
Wall-Link
main screen is displayed. To access any function and confirm the value press
REMOTE USER INTERFACE FOR
MICROSOL II PLUS
with the system in operation.
; to go back to the previous
. The following options are available in the
05-Clock
.
again to confirm the
.
Function unit
on the option corresponding to the event
.
at any time.
Finish time
. Then adjust the
to confirm or
to cancel.
at any time.
back to the previous menu or to leave any function without confirming press
The following options are available in the function menu:
01-Setpoint A1
02-Setpoint A2
Only with Microsol II plus from version 03
6.1 Auxiliary 1 setpoint
This function allows adjusting the control temperature for auxiliary output 1.
6.2 Auxiliary 2 setpoint
This function allows adjusting the control temperature for auxiliary output 2.
6.3 Sensor 2 overheating temperature
This function allows adjusting the overheating temperature for sensor 2. When applied to swimming
pools this is the limit temperature of the water (comfort temperature)
6.4 Water pump operating mode
This function allows adjusting the manual operating mode of the water pump.
6.5 Auxiliary 1 manual mode enable
The operating mode of the auxiliary 1 output can be toggled between manual and automatic by
pressing
6.6 Auxiliary 2 manual mode enable
The operating mode of the auxiliary 2 output can be toggled between manual and automatic by
pressing
version 03.
7. ACCESS MENU FOR ADJUSTING THE CONNECTION
Upon accessing the quick access menu while
will have two functions available for adjusting the address of Microsol II plus:
7.1 Microsol II plus address
The address of Microsol II plus controller can be manually adjusted by entering this function. The value
of this function must be the same value configured in Microsol II plus.
7.2 Search Microsol II plus
Pressing
on the
automatically. Enter the quick access menu again to stop the automatic search.
8. SETUP MENU
The operating characteristics of
function menu press
in the display. The following options are available in the setup menu:
01-McSol 485 Add
02-Interface
03-Descriptions
8.1 McSol2 485 Add
This function allows to manually adjusting the address of the Microsol II plus controller.
and
keys,
The value set for this function should be the same value set on the Microsol II plus.
8.2 Interface
Allows adjusting the user interface characteristics:
Fun
I01
Indication
I02
Language
I03
Display contrast
I04
Display timeout
I05
Sound signaling
shortly
; to
03-S2 Hi Temp
04-Pmp Activat
on this function.
on this function. Note: This option will be only available when the Microsol II plus is
Wall-Link
01-McSol 485 Add
02-Search McSol
on this function makes
Wall-Link
start searching for Microsol II plus address
Wall-Link
can be adjusted through the setup menu. To access the
and
keys simultaneously for eight seconds until the functions are shown
04-Timeouts
05-Statistics
Descrição
.
05-A1 Man Mode
06-A2 Man Mode
is not connected to Microsol II plus, the user
Mín.
Máx.
Unid
Padrão
S1
All
-
S2
-
-
-
Port
1
10
-
5
0
999
min.
0
Off
On
-
Off

Advertisement

loading
Need help?

Need help?

Do you have a question about the Wall-Link and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Full Gauge Wall-Link

  • Page 1 1. DESCRIPTION The following options are available in the function menu: Wall-Link is an interface intended to be used together with Microsol II plus from version 2 and above.
  • Page 2 Min Temp Alarm of minimum temperature on the sensor S1 Temp Alarm of maximum temperature on the sensor S1 Wall-Link is unable to locate Microsol II plus at address 1; High temperature alarm; Freezing temperature alarm; Sensor disconnected. Only with Microsol II plus from version 03...