Advertisement
Quick Links
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
2. Read through entire instruction before beginning assembly and installation.
NOTE: Components may be packaged in one or more additional boxes.
Parts
Support Angle (4)
(Part # UZ1665)
THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES
THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE
WARNING
OR IN THE THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL
NOT BE COVERED UNDER KWIK GOAL'S PRODUCT GUARANTEE. DO NOT LEAVE THIS
EQUIPMENT UNATTENDED.
ASSEMBLY INSTRUCTIONS FOR 9B1902 SHADE SHELTER
Seat Frame (3)
(Part# UZ1668)
90-1/2"
140 Pacific Drive Quakertown, PA 18951
800-531-4252 Kwikgoal.com
©
2019, Rev. 2020 Kwik Goal Ltd.
Bow (3)
(Part# UZ1663)
Crossbar (2)
(Part# UZ1664)
180-1/4"
END VIEW
NZ448 Rev. 01/16/20
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for KwikGoal 9B1902
Summary of Contents for KwikGoal 9B1902
- Page 1 ASSEMBLY INSTRUCTIONS FOR 9B1902 SHADE SHELTER 1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred, notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or damp packaging may damage contents.
- Page 2 NO PUSH OR PULL 90 OR PULL 90 NO PUSH OR PULL 90 PUSH OR PULL WITHIN 120 NEVER LEAVE SHELTERS UNATTENDED AND UNSECURED 140 Pacific Drive Quakertown, PA 18951 800-531-4252 Kwikgoal.com © 2019 Kwik Goal Ltd. NZ448 Rev. 01/16/20...
- Page 3 Parts Continued Plank (4) Bungees (34) Plank Hold Down (Part# UZ468 Plain) (Part#10B3501 PK 30) (See Bench Hdw) (Part # UZ1118 Color) (Part # UZ475) 15’-0” 7-5/8” Cover (1) (Part # VZ863) Swivel Wheel (4) Swivel Wheel w/ Brake (2) (Part# VZ629) (Part# VZ747) Kwik Fill Anchor Bag (4)
- Page 4 Parts Continued Note: Hardware is packed separately in one or more boxes. Open all boxes and layout all sealed hardware packs before beginning assembly. Anchor Hdw Shelter Hdw (Part#JZ269) (Part# JZ177) 3/8” X 2-1/2” Eye Bolt 5/16” X 1-1/4” Hex Bolt (24) (Part# TZ421) (Part# TZ311)
- Page 5 3. Hardware for steps 3 through 10 is in the Shelter Hdw and Bench Hdw packs. Attach plank hold downs to seat frame and hand tighten nut on carriage bolt at locations shown. Align plank hold down parallel with slot in plank, insert, and turn ninety degrees (quarter turn) to attach plank to seat frame.
- Page 6 5. Position plank to extend past end seat frame by Plank Bolts 1-1/2”. Be sure seat frame is square with plank and tighten both plank bolts. 6. Position center seat frame at 89-1/2” from end seat frame (secured in step 5), square seat frame with planks and tighten both plank bolts.
- Page 7 9. Attach swivel wheel assemblies to each of the three seat frames as shown. Wheel Assembly 5/16 Lock Nut 5/16 Flat Washer 5/16 X 1-1/4” Hex Bolt Swivel Wheel w/ Brake Swivel Wheel Swivel Wheel w/ Brake THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS.
- Page 8 10. Refer to step 3 for assembling the shelf planks to the seat frames. Tighten all shelf plank bolts. Turn shelter to the upright position. Plank THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS.
- Page 9 11. Hardware for steps 11 through 13 is in the Top Hdw pack. Attach 3 bows to seat frames as shown. Note: Do not over tighten bolts. 5/16” X 3” Hex Bolt 5/16” Flat Washer 5/16” Lock Nut Seat Frame 5/16”...
- Page 10 12. Attach crossbars to bows, making sure Kwik Goal is at the correct orientation as shown. Note: Do not over tighten bolts. 3/8” Square nut FRONT VIEW Crossbar Center Bow 3/8” Flat Washer 3/8” Lock Washer Crossbar 3/8” x 7/8” Hex Bolt Crossbar ASSEMBLED VIEW Crossbar...
- Page 11 14. When the crossbars are fastened to the bows turn the shelter so the top crossbar is down as shown. 15. Lay out cover along top crossbar with hem edge up. Making sure cover is evenly spaced between left and right bows, attach cover to top crossbar with cover clips as shown.
- Page 12 16. Attach cover to left bow at grommet with bungee as Bow Bungee shown. Repeat steps 15 & 16 to attach right side of cover to shelter frame. Note: For a clean look keep bungee ball on the inside of cover Left Bow Cover Top Crossbar...
- Page 13 18. Hardware for this step is in the Top Hdw pack. After cover is completely attached, turn shelter up on wheels and engage brakes on swivel wheels w/brake. Place crossbar caps on each end of crossbars. Crossbar Cap (4 Places) Crossbar Seat Frame 3/8”Lock Nut...
- Page 14 20. Attach remaining eye bolts to assembled shelter frames at back of shelter. 3/8”Lock Nut 3/8”Flat Washer 3/8”x 2-1/2” Eye Bolt THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS.
- Page 15 21. Hardware for this step is in the Bench Hdw pack. Attach remaining plank to all three seat frames. (Refer to step 5) Planks Seat Frame 1-1/2” Plank Plank Turn 90° Plank Hold Down 5/16" X 1-1/4" Carriage Bolt Plank 5/16”...
- Page 16 22. Permanent ground anchors must be used at all times. Dig four holes according to the layout below. Note: Areas subject to heavy frost may require depths as deep as 36”. Prepare holes and add drain stone as shown. Install anchor in each hole and fill hole with concrete.
- Page 17 23. Remove anchor plates from chains and attach chain to eye bolts at all 4 locations shown. Remove Anchor Plate Chain Snap Link Chain Assembled 4 Places Anchor Chain 1/2" Hex Bolt Ground Anchor THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS.
- Page 18 24. The ground anchor and chain leash system supplied is the recommended and the safest method of anchoring your shelter. However, anchor bags may be used as a temporary anchoring system. To ensure the anchor bags remain on the base of your shelter, you must attach them as shown in figure below. Crossbar Kwik Fill Anchor Bags Cover...
- Page 19 Crossbar Cover Cover Bungee Go to kwikgoal.com for additional product information. THIS UNIT MUST BE ANCHORED ACCORDING TO THESE INSTRUCTIONS AT ALL TIMES THIS EQUIPMENT MUST BE STORED IN A SECURED, SHELTERED AREA WHEN NOT IN USE WARNING OR IN THE THREAT OF HIGH WINDS. ANY WEATHER DAMAGE TO THIS EQUIPMENT WILL NOT BE COVERED UNDER KWIK GOAL’S PRODUCT GUARANTEE.
Need help?
Do you have a question about the 9B1902 and is the answer not in the manual?
Questions and answers