Download
Share
Print this page
Absco 45302WK Manual
  1. Manuals
  2. Brands
  3. Absco Manuals
  4. Storage
  5. 45302WK
  6. Manual

Absco 45302WK Manual

Workshop shed
Hide thumbs Also See for 45302WK:

Advertisement

Quick Links

Download this manual
AU: 1800 029 701
NZ: 0800 466 444
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: admin@absco.com.au or 1800 029 701
NOTE: This shed can be upgraded to wind
rating: C1 as per AS4055-2012 with the additional
purchase of a Cyclone Kit.
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
Absco Industries
Assembly Instruction Manual
ABSCO WORKSHOP SHED
MODEL: 45302WK
4.48mW x 3.00mD x 2.10mH
admin@absco.com.au
www.abscosheds.com.au
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
feedback@absco.com.au
ABSCO INDUSTRIES
ASSEMBLY INSTRUCTION MANUAL
Absco Industries
Premier Shed Model: 23151GK
When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.
LEAVE A REVIEW
SHED MODEL: 23151GK
Tell us about your experience and
receive a $20 Coles Gift Card.
Visit www.abscosheds.com.au/review
Model: 45302WK
FRONT: 2.26m
SIDE:
HEIGHT: 1.95m
BOTTOM CHANNEL
REBATED EDGE
75mm WIDE REBATE
CONCRETE SLAB
21-11-2017
17/03/21
1.2
1.52m
PAGE 01
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 45302WK and is the answer not in the manual?

Questions and answers

Related Manuals for Absco 45302WK

Summary of Contents for Absco 45302WK

  • Page 1 This will help water egress Http://www.abscosheds.com.au/watch-videos purchase of a Cyclone Kit. from the base of the shed. At ABSCO Industries we are always looking to be number ONE, so please let us know what you think of our instructions. Feedback makes us better. feedback@absco.com.au...
  • Page 2 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH GENERAL INSTRUCTIONS • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST"...
  • Page 3 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH COMPONENT PACKING LIST Check off all components. MAIN PACK CARTON (PACK 1 OF 2) COMPONENT PART COMPONENT PART CHECK CHECK DESCRIPTION DESCRIPTION MIDPOINT RIDGE STEEL SHEET 97AL BEAM 1852mm TO MIDPOINT...
  • Page 4 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH COMPONENT PACKING LIST FITTINGS & ACCESSORIES PACKET CONTENTS DOOR STRAP CHANNEL JOINER L: 165mm L= 200mm (7.9") CAP GABLE RIDGE L: 170mm PLATES PSTKDBL RIDGE CAP JOINER DOUBLE DOOR FITTING PACK...
  • Page 5 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH COMPONENT PACKING LIST MAIN PACK CARTON (PACK 2 OF 2) COMPONENT PART COMPONENT PART CHECK CHECK CHECK DESCRIPTION DESCRIPTION MIDPOINT STEEL SHEET STEEL SHEET 1785mm X 773mm 1852mm TO MIDPOINT...
  • Page 6 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH COMPONENT PACKING LIST 45302WCP CHANNEL PACK COMPONENT PART COMPONENT PART CHECK CHECK DESCRIPTION DESCRIPTION 55AL 55AR CHANNEL CHANNEL L = 1496.5mm L = 1496.5mm 55BL 55BR CHANNEL CHANNEL L = 1496.5mm L = 1496.5mm...
  • Page 7 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH COMPONENT PACKING LIST 45302WCP CHANNEL PACK (CONT.) PART COMPONENT PART COMPONENT CHECK CHECK DESCRIPTION DESCRIPTION CHANNEL CHANNEL WITH HINGES L = 1518mm L = 1725mm CHANNEL CHANNEL L = 1518mm...
  • Page 8 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH SNAPTiTE ASSEMBLY GUIDE The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners. To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
  • Page 9 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH Guide on Joining Spliced Channels The text marked on all parts must be shown on the same side as each other JOIN>> JOIN>> <<JOIN JOIN>> Step 1. Step 2. Position the channels and the...
  • Page 10 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH PRE-ASSEMBLY OF SPLICED CHANNELS Join together 20 x channel sections using 10 x channel joiners (Part CSJ) NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them.
  • Page 11 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH Guide on Joining a Spliced Ridge Beam Follow these three steps to assemble a ridge beam. ZARSP 225mm 50mm Step 1. NOTE. Step 2. Place two ridge beams as There is a 50mm overlap of the Use the ZARSP to connect at shown and push them together.
  • Page 12 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH PRE-ASSEMBLY OF SPLICED RIDGE BEAM ZARSP = 1x 97A 1x 97AL 1x 97AR Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 13 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH JOINING RIDGE BEAMS To make the total span we must now join the two ridge beams Cut away these two only. Using a hacksaw, remove one protruding section of each ridge beam, this will allow the sections to butt up neatly to each other.
  • Page 14 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH OVERVIEW OF ROOF COMPONENTS Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 15 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH OVERVIEW OF WALL COMPONENTS Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...

  • Page 16: End Panel Assembly

    ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH END PANEL ASSEMBLY 1x required. 1x required. Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 17 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH LARGE ROOF PANEL ASSEMBLY 2 required. When completed there will be two sections with 87A lip at one end only. One panel will have part 87A fitted to this end only.
  • Page 18 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH SMALL ROOF PANEL ASSEMBLY 2 required. When completed there will be two sections with 87A lip at one end only. One panel will have part 87A fitted to this end only.

  • Page 19: Front Panel Assembly

    ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH FRONT PANEL ASSEMBLY 1 required. Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 20 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH FRONT PANEL ASSEMBLY 1 required. Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 21 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH DOUBLE DOOR ASSEMBLY 1 required. Vertical door channels are installed in the opposite orientation compared to the horizontal door channels. Long Short fl ange fl ange of of channel channel Four hole set for padbolt connection.

  • Page 22: Door Panel Assembly

    ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH DOOR PANEL ASSEMBLY Nuts and bolts may be used instead of pop rivets by drilling out hinge holes using a 4mm drill bit. Both are supplied. The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and secure with screws.
  • Page 23 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH JOINING WALL AND ROOF PANELS To make the total span we must now join sections of sheeting together for the roof and wall. Trim the channels by 16.5mm to 16.5 16.5...

  • Page 24: Side Panel Assembly

    ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH SIDE PANEL ASSEMBLY 2 required. Trim the tip of each sheet or bend out of the way to allow channels to fit hard up to the edge of the sheet.
  • Page 25 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL FRAME DETAILS 1 required. PART C1482 PART C1704 80mm TIP: An easy way to make sure that the angle at the top of the portal frame is correct is to use the gable wall panel as a template to lay the sections out.
  • Page 26 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL FRAME DETAILS STEP 1. x 19 STEP 2. Secure ridge plates x 30 to apex plates STEP 3. M10 Dynabolt STEP 4. 45mm TEK SCREW Portal to panel connection, see section PANEL CONSTRUCTION for further infomation.
  • Page 27 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 1. Draw pattern on the concrete in accordance with the dimensions detailed in the assembly instructions. Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 28 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 2. Understand where components are to be positioned Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 29 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 3. Join rafter to column with knee plate Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 30 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 4. Join both rafters using the apex plate Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 31 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 5. Secure ridge plate (RBP) Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 32 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 6. Secure multi purpose brackets Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 33 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH CENTRE PORTAL ASSEMBLY SUPPORT PHOTOS STEP 7. Turn frame over and repeat steps 4 and 5. Absco Industries Assembly Instruction Manual Model: 45302WK 17/03/21...
  • Page 34 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH PORTAL FRAME DETAILS FIG 8A 1550 3030 Concrete slab Centreline of frame 4580mm x 3100mm uprights 4580 Multi purpose Centre frame brackets upright 80mm long SLAB EDGE • Secure multipurpose brackets to uprights using self drilling screws •...
  • Page 35 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH PANEL CONSTRUCTION NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. The base channels are not.
  • Page 36 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH ROOF CONSTRUCTION STEP 1. STEP 3. Secure peak brace to ridge beam and Secure both roof panels to the walls with roof panel with one screw at each end, one screw in each corner first, followed see A below.
  • Page 37 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH FINAL CONSTRUCTION ANCHORING OF SHED Refer to section STEP 1. PORTAL FRAME Secure the roof panels to the wall panels for portal anchor as shown. Location of 20 concrete locations.
  • Page 38 • 2.G The drawings provided herein are for installation and structural engineering purposes only. If discrepancies are discovered within the documentation provided, these shall be brought to the attention of Absco and written approvals obtained prior to commencing the affected section of work.
  • Page 39 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH Absco Large Gable Roof Shed Notes Steelwork • 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 2312- 2002. • 2.S All structural steelwork detailed within this installation manual shall be minimum Grade 550 for roll formed sections (including roof and wall sheeting and portal frame members) and Grade 250 for angle sections.
  • Page 40 ABSCO WORKSHOP SHED MODEL: 45302WK 4.48mW x 3.00mD x 2.10mH Absco Large Gable Roof Shed Notes Supporting Slab and Foundations • 1.F The supporting slab foundation for the garden shed shall be of a minimum size indicated on the installation manual.
  • Page 41 • Absco accepts no responsibility for water entry, fl oor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.
  • Page 42 Absco, along with a copy of your proof of purchase. The benefi ts of this warranty are in addition to your rights under the Australian Consumer Law (ACL) and in particular, the guarantees implied under the ACL and any other rights and remedies of the consumer under a similar law in relation to the goods and services to which this warranty relates.
  • Page 43 If you do not wish to register your warranty online, complete the below form and email, fax or post this form back to Absco, along with a copy of your proof of purchase. NAME:...