Related Manuals for Ultima RT25/50
Summary of Contents for Ultima RT25/50
- Page 1 HT18/36 RT25/50 Regular Traffic High Traffic 12V/24V 12V/24V • • 25/50m per min 18/36m per min • • 500/300kg 600/300kg • • Proudly manufactured by www.dace.co.za Ver 1.01...
-
Page 2: Table Of Contents
Page Table of Contents —————————————————————————————–—————— Foreword —————————————————————————————————-- Abbrevia ons Introduc on & Recommenda ons ——————————————————–———————- Specifica ons Ul ma Operator ———————————————————————–——————- Tritek Controller ———————————————————————–——————- Operator & Site Basics Operator Parts Iden fica on ————————————————–———————— 7 Site Layout ————————————————————————————————- 8 Gate Pull & Running Forces ————————————————————————- 8 Cable Recommenda ons ——————————————————–———————-- Installing the Operator... -
Page 3: Abbrevia Ons
FOREWORD Thank you for choosing Dura Access Control Equipment (DACE). We welcome you to the ever growing community of happy DACE product owners. The advanced engineering and high-quality construc on of each DACE product we build is something of which we are proud. The Ul ma gate operator is packed with features to bring you more convenience and to enhance your security. -
Page 4: Specifica Ons
INTRODUCTION & RECOMMENDATIONS DACE is a proven leader in the manufacturing of automa c gate & garage operators and strives to manufacture high quality products using the latest technology. We are constantly working on upgrading our products to bring you, our clients, products of the finest quality. We strongly recommended using the services of an experienced gate installer to install your gate opera- tor but if you intend installing the operator yourself, the manual must be read carefully before any installa on begins. - Page 5 2. Between the gate & the end stop 6. Between the gate operator & the gate 3. The gate, during the closing cycle 7. Gate Rollers/An -li device 4. Between the gate & the catch bracket 8. The gate, during opening cycle ULTIMA TECHNICAL SPECIFICATIONS...
-
Page 6: Tritek Controller
TRITEK CONTROLLER SPECIFICATIONS Con nues……... -
Page 7: Operator Parts Iden Fica On
……..con nued OPERATOR PARTS IDENTIFICATION PARTS LIST 1. Tritek Controller 6. Founda on Plate 11.Transformer 2. Rev Counter Housing 7. Height adjustment Nuts 12.Ba ery 3. 12 Volt DC Motor 8. LCD Interface 13.GSM/WiFI Module Input 4. Cam Lock 9. Joys ck 14.Marker Sensor 5. -
Page 8: Site Layout
SITE LAYOUT 1. Intercom Gooseneck 5. Exit Loop 9. Guide Rollers 2. Catch Bracket 6. Isolator Switch 10.Pillar Light 3. Close Safety Beam 7. Marker Magnet 4. End Stop 8. Open Safety Beam GATE PULL & RUNNING FORCES The gate Pull and Running Forces must be measured before installing the operator. - Page 9 GATES ON A GRADIENT We do not recommend automa ng a gate which is not level. Failure to level the gate will put undue stress on the operator. Furthermore, if the operator is in manual override mode, the gate may run freely down the slope and present a safety risk.
-
Page 10: Cable Recommenda Ons
CABLE RECOMMENDATIONS Two op ons for power supply: 1. Op on 1 (Recommended): Low voltage supply 14-24V AC via transformer placed in the house, max 50m from operator with 3 core 1.5mm (Live, Neutral & Earth). 2. Op on 2: High voltage mains supply connected to a 220V/240V AC Double Pole Isolator switch, mounted within 1.5m of the operator connected to the transformer inside the operator. -
Page 11: Anchoring The Founda On Plate
ANCHORING THE FOUNDATION PLATE Lay a concrete slab 400mm x 400mm x 200mm: Dig a hole and place the conduit ❶ in the correct • posi on. Fill the hole with concrete & allow to set. • II. Place the founda on plate on the concrete slab & feed the conduit through the cable inlets ❷. -
Page 12: Securing Operator To The Founda On Plate
SECURE OPERATOR TO THE FOUNDATION PLATE 1. Raise the adjus ng nuts ~ 5mm before moun ng the SIDE VIEW operator to allow for fine height adjustment at a later 2. Mount the operator on the founda on plate. 3. Place a Spirit Level on top of the operator base while Securing Nuts fastening the three securing nuts and washers ensuring that the operator is level. - Page 13 ……..con nued 1. Rest the rack on the pinion with the end of the rack and the end of the gate aligned. Having the gate slightly open will allow access to the first slot on the rack. 2. Clamp the opposite end of the rack to the gate. 3.
-
Page 14: Placing Oil In The Gearbox
PLACING OIL IN THE GEARBOX It is important that the gearbox be filled with oil before commissioning the operator. Only use SAE75W-90 oil to refill. Fill the gearbox with the oil provided as shown. The The gearbox oil will need to be topped up periodically. en re bo le (70ml) must be emp ed into the gearbox. -
Page 15: Tritek Control Board Layout
TRITEK CONTROL BOARD LAYOUT 20A FUSE REV COUNTER MARKER GSM/WiFi BATTERY –VE MOTOR INPUT INPUT INPUT 3A FUSE JOYSTICK SPEAKER BATTERY AUX OUTPUT BATTERY +VE 12V - 24V OVERVIEW OF POWER CONNECTIONS & FUSES FUSE 20A: this fuse protects the motor in ♦... -
Page 16: Overview Of Low Power Inputs & Outputs
OVERVIEW OF LOW POWER INPUTS & OUTPUTS INF-GND: this is a dedicated ground, used to connect ♦ certain brands of safety beams that have the capacity of performing a self test func on, such as the DuraOp cs Wireless Beams. INF/CLS: connect to the safety beam relay or FET output ♦... -
Page 17: Charging Supply Op Ons
CHARGING SUPPLY OPTIONS MAINS 220-240V AC HOUSE EARTH WARNING!!! WHEN USING A SOLAR PANEL DISCONNECT THE TRANSFORMER NOT POLARITY SENSITIVE SOLAR PANEL MAX 40V DC... -
Page 18: Menu Naviga On Overview
MENU NAVIGATION OVERVIEW IDLE MODE The LCD screen will remain in Idle Mode if the Joys ck has not been moved for awhile and will scroll through the following 3 screens. JOYSTICK MENU NAVIGATION The Joys ck moves in 5 direc ons: UP (North); DOWN (South); LEFT (West); RIGHT (East) for naviga on and IN- WARD (Press) for item selec on. -
Page 19: Commissioning The Operator For The First Me
……..con nued INFORMATION SCREEN MENU ICONS: Ba ery - Displays the current ba ery voltage, charge current and charge voltage. Mains Supply - Displays the current type of supply, supply voltage and output voltage. GSM / WiFi - Displays the status of the GSM or WiFi module connected to the controller Gate - Displays the number of opera ons, average force and maximum force of the gate while running Receiver - Displays informa on about the last remote signal that was received. -
Page 20: Two Sets Of Safety Beams (Relay Output)
TWO SETS OF SAFETY BEAMS (RELAY OUTPUT) MAX. LOAD 300mA... -
Page 21: External Radio Receiver & Loop Detector
EXTERNAL RADIO RECEIVER & LOOP DETECTOR MAX. LOAD 300mA... -
Page 22: Closing Safety Beam (Fet Output & Relay Output)
CLOSING SAFETY BEAM (FET OUTPUT) CLOSING SAFETY BEAM (RELAY OUTPUT) -
Page 23: Opening Safety Beam (Fet Output & Relay Output)
OPENING SAFETY BEAM (FET OUTPUT) OPENING SAFETY BEAM (RELAY OUTPUT) -
Page 24: Connec Ng Common External Devices
CONNECTING COMMON EXTERNAL DEVICES HOLIDAY LOCK OUT (Normally Open) (Keypad, Receiver, Keyswitch) PEDESTRIAN OPENING (Keypad, Receiver, Keyswitch) (Normally Open) FULL OPEN (Intercom) (Normally Open) STATUS LED (Intercom) TAMPER SWITCH Tamper Switch is CLOSED when the lid is removed (Normally Closed) -
Page 25: Connec On For Relay Module
CONNECTION FOR RELAY MODULE OUTPUT DEPENDANT ON VOLTAGE OF BATTERY FITTED. ENSURE ALL EXTERNAL DEVICES ARE CORRECTLY RATED. MAX. LOAD of 100mA DACE DACE Relay Module Relay Module ZONE BYPASS LIGHT... -
Page 26: Electric & Magne C Locks
ELECTRIC LOCK ELECTRIC LOCK 3A MAX MAGNETIC LOCK MAGNETIC LOCK 500mA max @ 12V 250mA max @ 24V... - Page 27 CONNECTING VARIOUS DEVICES TO PULSE & ALARM OUTPUTS (USING RELAY MODULE) SIREN DACE Relay Module BELL DACE CAUTION!!! Relay Module OUTPUT DEPENDANT ON VOLTAGE OF BATTERY FITTED. ENSURE ALL EXTERNAL DEVICES ARE CORRECTLY RATED. MAX. LOAD 300mA WIRED ALARM BUZZ BELL GATE ALARM...
-
Page 28: Two Synchronised Operators Connected To One Set Of Safety Beams
TWO SYNCHRONISED OPERATORS CONNECTED TO ONE SET OF SAFETY BEAMS (USING BEAM RELAY OUTPUT) OPERATOR CONTROL BOARD NO. 1 WARNING!!! ONLY CONNECT +BATT TO ONE MOTOR AS SHOWN OPERATOR CONTROL BOARD NO. 2 MAX. LOAD 300mA WARNING!!! ONLY CONNECT BEAMS RECEIVER GND TO TRITEK COM-GND... -
Page 29: Control Board Func Ons
Note the following func ons on the TRITEK menu: Help To get help on any of the onboard func ons, move the cursor to the specific icon for which more informa on is required. If the cursor is le standing on the same icon for more than six seconds, a help screen will automa cally appear. -
Page 30: Auto Close Setup
AUTO CLOSE SETUP To prevent accidents, Safety Beams must be used when enabling the Auto Close func on. Enable Auto Close Enabling this func on allows the gate operator to Auto Close. If the gate is obstructed and Safety Beams are connected, the Auto Close Time delay will reset when the obstruc on is removed. - Page 31 ……..con nued Add Remotes (With groups) If the controller has more than just the original Group 0, it will prompt for the group number to which the new remote/s must be added. A er selec ng the required group number follow the same steps as listed in Add Remotes (No groups).
-
Page 32: Pedestrian Entry
……..con nued Copy Group This feature copies the se ngs from one group, thereby making it easy to set up a new group with just minor adjustments. When se ng up a new group for the first me, use the ‘Copy Group’ func on to copy Group 0, thereby crea ng a new group, and then use the ‘Edit Group’... -
Page 33: Light Se Ngs
LIGHT SETTINGS Courtesy Light Usually used to switch pillar lights on when the operator is triggered. The light output must be connected to an EXO Relay Module. Do not connect mains directly to the controller. Set Light Timer This function sets the length of time that the light will remain on if the Courtesy Light option is enabled. Flash On Moving If enabled, the light connected to the light output on the controller will flash while the gate is moving. -
Page 34: Lock Se Ngs
……..con nued Alarm Dura on This se ng adjusts the dura on that the alarm output will remain ac ve. Hold Alarm This se ng will keep the alarm output ac vated for as long as an alarm condi on persists. The alarm output will only switch off... -
Page 35: Opera Ng Modes
OPERATING MODES Standard Mode In Standard Mode the gate will : open if it receives a trigger when in the closed posi on. • return to the closed posi on if it receives a trigger while open. • stop if it receives a trigger while it is opening. •... -
Page 36: Usb Se Ngs
……..con nued Deep Sleep This func on places the controller into ‘Deep Sleep’ when the input power supply fails. Internal process- es, LEDs and external devices connected to the controller are switched off. Receiver response me is slightly reduced. Ba ery standby me is increased by ± 1200%. Solar Sleep If enabled, this func on allows the controller to enter into the selected sleep mode (Light, Medium or Deep) while the input supply voltage is at a normal level. -
Page 37: Hid Se Ngs
HID SETTINGS (Human Interface Device) Contrast Adjust the display contrast for be er viewing. Cursor Speed Adjust the cursor speed for easier selec on of icons. Click Speed Adjust how fast the joys ck reacts to being held down or mul ple presses. Voice Assistant Enable or disable the Voice Assistant during programming. - Page 38 ……..con nued Before using Time Manager ensure that the controller Date and Time are set correctly. Set Time & Date This func on sets the controller me and date. Set Time Period (120 Periods & Exclusions in total) Use this func on to set up new Time Periods following these steps. ❶...
-
Page 39: Gate Setup
GATE SETUP Setup Wizard This func on automa cally programs the open and closed gate limits. The Setup Wizard will run auto- ma cally a er the first power up of a new operator or a er a gate factory reset (see Use Factory Se ngs). - Page 40 ……..con nued Open Ramp Up Adjusts the Ramp Up distance before maximum running speed is reached when the gate is opening. Opening Speed Adjusts the maximum opening speed. Open Ramp Down Adjusts the Ramp Down distance before running at crawl speed when the gate is opening. It should be noted that a very short ramp down may damage plastic rack or place unnecessary strain on the gate motor, especially if the gate is heavy.
-
Page 41: Holiday Lockout
……..con nued Posi ve Close If enabled, the open and close gaps are ignored and the gate will stop touching the end stops. This is usually used in conjunc on with electric fencing where it is required that the gate stops against contacts for the electric fence. -
Page 42: Upgrading Controller So Ware
UPGRADING CONTROLLER SOFTWARE Step 1: Download the latest version of the Tritek controller so ware from www.dace.co.za or it can be received by WhatsApp or email. Step 2: Save the so ware onto a USB Flash Drive or into the Downloads directory in a compa ble Android phone. - Page 43 ……..con nued ANNUALLY Many sealed lead acid ba eries do not last for more than one year. The ba ery condi on can be checked by ♦ disconnec ng the mains supply to the operator. Go to Quick NAV on the LCD screen and press the joys ck to enter the Info menu.
-
Page 44: Warning Messages
……..con nued MESSAGE DESCRIPTION TRIGGER The operator received a trigger signal. PEDESTRIAN The operator received a pedestrian trigger. LOOP The operator received a loop trigger. ACTIVATION IS NOT POSSIBLE WHEN THERE IS If the ba ery voltage is too low, the controller will not ac vate the gate. A BATTERY FAULT CONDITION ACTIVATION IS NOT... - Page 45 ……..con nued MESSAGE DESCRIPTION & SOLUTION The Safety Beams are blocked or faulty. CLOSING IR Remove anything that may be obstruc ng the beams. BEAM ♦ Look on the controller to see what beam input is ac ve. Check that the beam connected BLOCKED ♦...
-
Page 46: Glossary
……..con nued MESSAGE DESCRIPTION & SOLUTION ENCODER The controller has detected an encoder fault. FAULT Ensure that the controller is si ng properly on the controller base. ♦ If a Tritek controller is being used on a older DACE product i.e. not an Ul ma, check that the ♦... - Page 47 ……..con nued See Controller Main PC Board Allows the gate to be moved manually. Manual Override Used in a Townhouse applica on. The controller will not accept a trigger while opening Mul User Mode to prevent the accidental closing of the gate on a vehicle/person. Gate motor.
-
Page 48: Technical Specifica Ons
TECHNICAL SPECIFICATIONS CONTROLLER SYSTEM Main - ARM core - 90 DMIPS Dual Processor Supply - Microchip - 8 MIPS Intelligent mul stage dual switch mode Supply 3.5V, 5V, 7V, 13 - 29.4V Single / Dual H-Bridge 56 Amp Motor Drive INF/CLS, INF/OPN, LOCK, TRIG, PED, LOOP, LIGHT, TAMPER, REV1, MARKER1, GSM Inputs LIGHT, LOCK, ALARM, PULSE, STATUS, MOTOR... -
Page 49: Terms & Condi Ons
……..con nued SECURITY FEATURES Securi-Lock gate forced alarm, Ambush alarm, Break in alarm, Tamper alarm, Gate Alarm Inputs open alarm Open Collector (200mA) Alarm Outputs Electric or Magne c Lock Courtesy and Warning Light GATE 600kg (maximum) Gate Mass 55 m/min (maximum) Gate Speed 270 N (maximum) Push Force... - Page 50 NOTES Recommenda ons of notes that should be kept: » Groups - group number and group members » Time Manager slots - Time Period and Exclusion Period numbers » Remote users and the respec ve remote number (label the remotes) »...
- Page 51 NOTES...
-
Page 52: Warranty & Disclaimer
WARRANTY DACE warrants that Ul ma operators will be free from defects in material and workmanship for a period of 24 months of opera on. Where opera onal data is not available, the warranty claim must be accompanied by the original invoice.