Advertisement
$ DO NOT operate the saw if any parts are damaged or missing as this may cause failure and/or personal injury.
$ DO NOT operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
# When not in use switch off the saw and unplug from the power supply.
! WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
# Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
# Keep hands and body clear of the blade when operating the saw.
# Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
# Keep children and unauthorised persons away from the work area.
# Avoid unintentional starting and never leave the saw operating unattended.
$ DO NOT use the saw for a task it is not designed to perform and ensure operators are trained to use the saw.
$ DO NOT get the saw wet or use in damp or wet locations or areas where there is condensation.
$ DO NOT use the saw where there are flammable liquids, solids or gases such as paint solvents and including waste cleaning rags etc.
1.3.
SPECIFIC SAW SAFETY RULES
# Connect to a suitable extraction system. Failure to do so will result in the build-up of sawdust which could become a fire hazard.
# Keep blade guard in place and operational.
! WARNING! Before each use, check that the saw blade is secure and not worn or damaged.
# Check workpiece to ensure that there are no nails or other items which may foul the saw blade.
# Hold the workpiece firmly against the fence.
# Avoid subjecting the saw blade to excessive strain - never force the blade down. Maintain a controlled, steady progression.
# Should the saw blade jam, switch the power off immediately to prevent damage to the motor.
# Provide adequate support to the sides of the saw table for long or wide workpieces.
$ DO NOT place yourself in an awkward operating position where a slip could cause your hand to move into the cutting blade.
$ DO NOT stand, or have any part of your body, in line with the path of the saw blade.
$ DO NOT hold what will become the off-cut (the waste part of the workpiece).
! WARNING! DO NOT put hands anywhere near the blade whilst it is rotating.
! WARNING! DO NOT attempt to free a jammed saw blade without first switching off or removing the plug from the mains power supply.
$ DO NOT cut metals or substances that may produce toxic dust. Saw must only be used to cut wood or wood derived substances and plastics.
$ DO NOT attempt to cut round section wood.
$ DO NOT use solvent to clean plastic parts, it may damage them. Use a soft damp cloth only.
# Store blades in a safe, dry childproof location.
2. SPECIFICATION
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . .230V - 1050W
Blade speed . . . . . . . . . . . . . . . . . . . . . . . . . .4800rpm
Saw blade . . . . . . . . . . . . . . . . . . . .Ø205mm x 30mm
Capacity at 90
. . . . . . . . . . . . . . . . . . . . .80 x 80mm
O
3. INSTALLATION
WARNING! ENSURE THAT THE SAW IS NOT CONNECTED TO THE MAINS POWER WHEN INSTALLING.
!
The SM8.V2 saw is supplied fully assembled and only requires to be bench mounted and connected to a dust-extraction system.
3.1.
Mounting
The saw should be bolted to a sturdy workbench. Ensure that the supporting surface is strong enough to take the weight of the saw
and any workpiece. Position the saw in a suitable work area with enough clearance to allow room when working with large workpieces.
Ensure that there is adequate lighting and that the saw blade can be clearly seen.
3.2.
Extraction
Connect the outlet (fig.2.19) to a suitable dust-extraction system.
WARNING! Wood dust can be harmful by inhalation and skin contact. Concentrations of small dust particles in the air can form
!
an explosive mixture. Therefore, ensure that there is adequate ventilation and that the saw is attached to a dust-extraction unit.
4. ADJUSTMENTS
WARNING! ALWAYS DISCONNECT SAW FROM THE MAINS POWER BEFORE MAKING ANY ADJUSTMENTS.
!
4.1.
Table
4.1.1. To adjust the table (fig.1.8) loosen the two locking screws (fig.1.10). The table can now be rotated.
4.1.2. At the front of the base plate is a datum line, align table to the required angle on the scale, then tighten locking screws.
4.2.
Blade
4.2.1. To open saw, lightly press down on the handle (fig.1.2) and at the same time pull out the locking pin (fig.2.16). Control the spring-
loaded saw arm up until it reaches the fully raised position.
4.2.2. The blade can be tilted by up to 45
angle and then firmly re-tighten the clamp screw.
Initial set-up - before first use, set blade angle to 0
(fig.3.A). If it is not correct, loosen lock nut and adjust stop screw (fig.3.12 &17) to give 90
Also set the blade to 45
and stop screw on the opposite side (fig.4.11&18).
4.3.
Changing the blade
4.3.1. Move the saw arm / blade up to full height.
4.3.2. Remove the guard screw (fig.5.20), unclip the blade cover at the rear, and then hinge the cover upwards (fig.5.15).
4.3.3. Use the blade locking tool (fig.5.21) to hold the outer blade flange whilst undoing the blade retaining bolt, by turning it clockwise
(LH thread) with an allen key (fig.5.B). Remove the outer blade flange and the saw blade with care. Wear suitable protective gloves
to protect the hands from the blade, which is very sharp. Note order of all components.
4.3.4. When fitting the new blade it is very important to ensure that the direction arrow on the blade matches the arrow on the blade
guard. Clean shaft and flanges, then fit washer, blade, outer blade flange and bolt. Fully tighten bolt.
4.3.5. Hinge down the cover into place and fully tighten retaining screw.
to the left by loosening the clamp screw (fig.1.13) using an allen key. Adjust to the required
O
and check that the blade to table angle is 45
O
,
Capacity at 45
O
Capacity at 45
O
Dust extraction port Ø . . . . . . . . . . . . . . . . . . . .38mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.6kg
on scale and confirm, using a square, that the blade is at 90
O
(fig.4.A). Any required adjustment is provided by lock nut
O
. . . . . . . . . . . . . . . . . . . . .50 x 70mm
and 90
. . . . . . . . . . . . . . .80 x 50mm
O
, retighten lock nut.
O
to the table
O
SM8.V2 - 1 - 240806
Advertisement
