Rough-In Dimensions; Unpacking; Reversing Door Swing - Frigidaire FEQ332 Installation Instructions Manual

TOP CONSOLE MODELS

ROUGH-IN DIMENSIONS

ROUGH-IN DIMENSIONS
ROUGH-IN DIMENSIONS ROUGH-IN DIMENSIONS ROUGH-IN DIMENSIONS
(68.3 cm) (68.3 cm) (68.3 cm) (68.3 cm) (68.3 cm)
ELECTRIC CONNECTION ELECTRIC CONNECTION
ELECTRIC CONNECTION ELECTRIC CONNECTION ELECTRIC CONNECTION
(6.5 cm) (6.5 cm) (6.5 cm) (6.5 cm) (6.5 cm)
13 1/2" 13 1/2"
13 1/2" 13 1/2" 13 1/2"
(34.4 cm) (34.4 cm)
(34.4 cm) (34.4 cm) (34.4 cm)
3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA. 3/8" (0.96 cm) DIA.
GAS PIPE GAS PIPE GAS PIPE
GAS PIPE GAS PIPE
(9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm)
REAR VIEW REAR VIEW REAR VIEW REAR VIEW REAR VIEW
47 1/2" 47 1/2" 47 1/2" 47 1/2" 47 1/2"
(120.7 cm) (120.7 cm) (120.7 cm) (120.7 cm) (120.7 cm)
SIDE VIEW SIDE VIEW
SIDE VIEW SIDE VIEW SIDE VIEW
(110.7 cm) (110.7 cm) (110.7 cm)
(110.7 cm) (110.7 cm)
(2.54 cm) (2.54 cm)
(2.54 cm) (2.54 cm) (2.54 cm)
4 3/8" 4 3/8"
4 3/8" 4 3/8" 4 3/8"
(11.1 cm) (11.1 cm) (11.1 cm) (11.1 cm) (11.1 cm)
OPTIONAL OPTIONAL
OPTIONAL OPTIONAL OPTIONAL
VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT VENT KNOCKOUT
(68.6 cm) (68.6 cm) (68.6 cm) (68.6 cm) (68.6 cm)
1. Using the four shipping carton corner posts (two on each
side), carefully lay the dryer on its left side and remove foam
shipping base.
as a means to pick up or move the dryer.
NOTE: On under counter model clothes dryers, the top panel
may be removed for installation.
2. Return the dryer to an upright position.
36" 36"
36" 36" 36"
(91.5 cm) (91.5 cm)
(91.5 cm) (91.5 cm) (91.5 cm)
Your dryer is designed so the door swing may be reversed at
any time without additional parts. Conversion is accomplished
by transferring hinges to the opposite side of the cabinet.
To change the direction of the door opening:
1. Open the dryer door. Remove the four hinge hole plugs from
the left side of the door opening. Place nearby for future
installation. NOTE: You may need a plastic knife to help pull
out the plugs. Be careful not to scratch the paint.
2. Remove the four screws that secure the door hinges to the
dryer front panel (see below). NOTE: Remove one screw
from each of the two hinges first. Hold the door firmly before
removing the last two screws.
3. Rotate the door 180° and reinstall the door hinges to the
dryer front panel with the four screws.
4. Install the four hinge hole plugs in the open screw holes on
the right side of the door opening.
3 3/4" 3 3/4" 3 3/4" 3 3/4" 3 3/4"
(9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm) (9.5 cm)
6

UNPACKING

To prevent damage, do not use the control panel
FOAM
SHIPPING

REVERSING DOOR SWING

PACKING
REMOVE 4 SCREWS
(ONE FROM EACH
HINGE FIRST)