Advertisement
Quick Links
Advertisement
Related Manuals for iBell RH26-26
Summary of Contents for iBell RH26-26
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. GENERAL POWER TOOL SAFETY WARNINGS ___________ 2. ROTORY HAMMER SAFETY WARNINGS_________________ 3. PRODUCT OVERVIEW __________________________________ 4. PRODUCT SPECIFICATIONS ____________________________ 5. SETUP _________________________________________________ 6. PRODUCT FUNCTIONS AND ASSEMBLY ________________ 7. GENERAL OPERATION _________________________________ 8. TROUBLESHOOTING ___________________________________ IBL RH26-26/24... -
Page 4: General Power Tool Safety Warnings
Keep it away from heat, oil, sharp edges or moving parts. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. IBL RH26-26/24... - Page 5 When servicing a power tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of shock or injury. IBL RH26-26/24...
- Page 6 Injuries and damage to property due to broken cutting attachments or the sudden impact of hidden objects during use. Danger of injury and property damage caused by other objects or due to natural reactions or calamities. IBL RH26-26/24...
-
Page 7: Rotory Hammer Safety Warnings
Improperly reconditioned chisels could cause injury. Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands. IBL RH26-26/24... -
Page 8: Product Overview
PRODUCT OVERVIEW 1. SDS Plus Chuck/Tool Holder 2. Mode Adjustment knob (Selector and button) 3. Forward/Reverse rotation control lever 4. Switch lock on button 5. ON/OFF Switch 6. Auxiliary Handle 7. Depth rod 8. Depth rod adjustment button IBL RH26-26/24... -
Page 9: Product Specifications
: 26 mm Additional Chuck capacity : 13 mm Max Drill diameter : Masonry – 68 mm Concrete – 26 mm Wood – 30 mm Steel – 13 mm Spindle collar diameter : 50 mm Protection class : Class II IBL RH26-26/24... -
Page 10: Setup
For safety reasons it is essential to read the entire instruction manual before first operation and to observe all the instructions mentioned in it. IBL RH26-26/24... -
Page 11: Product Functions And Assembly
Only change the rotational direction when the product is switched off and has come to a complete stop! Always push the forward/reverse rotation control as far as it will go! Do not use the product with the control switch in any other intermediate position! IBL RH26-26/24... - Page 12 To use the depth rod, first insert the required drill bit. Press the depth rod button (8) and keep it pressed. Fit the depth rod through the hole in the depth stop clamp on the auxiliary handle. Adjust the drilling depth required and release the button. IBL RH26-26/24...
- Page 13 SDS-plus shank should be same as the drill bit used and so follow the steps referred above. Drill Chuck + Chuck Adaptor Chuck wrench; used for tightening or loosening the jaws of a chuck. IBL RH26-26/24...
- Page 14 Press the mode selector button and turn the mode selector knob until it points to the ‘bit rotation/hammer-drilling’ position. Rotate the chisel to the desired position. Set the mode selector switch to the ‘hammering only’ position. Twist the chisel until it locks in position. IBL RH26-26/24...
-
Page 15: General Operation
Remove blocked and stuck drill bits by changing the rotational direction. Adjust the auxiliary handle as required. If necessary, set the depth rod. Always switch off the tool when work is finished and before unplugging. IBL RH26-26/24... - Page 16 Do not attempt to use the rotary hammer in the rotation and striking function with the drill chuck and chuck adaptor attached. This would seriously shorten the service life of every component of the machine. IBL RH26-26/24...
- Page 17 WARNING! from the power supply and let the product cool down before performing inspection, maintenance and cleaning work! Only perform repairs and maintenance work according to these instructions! All further works must be performed by a qualified specialist! IBL RH26-26/24...
-
Page 18: Troubleshooting
Only perform the steps described within these WARNING! instructions! All further inspection, maintenance and repair work must be performed by an authorised service centre or a similarly qualified specialist if you cannot solve the problem yourself! IBL RH26-26/24... - Page 19 Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. Do not dispose this product by normal household waste, but take it to a collection point and recycling of electrical and electronic equipment.