Advertisement
Quick Links
INSTALLATION INSTRUCTION FOR SINGLE GLASS SOLAR MODULE
S
ingle glass solar modules are made of 120/132/144/pcs of 158.75mm×79.375mm crystalline solar cells in
series with high efficiency, high transmission and low iron toughened glasses , anti-aging EVA and high flame-
resistant back sheet to laminate, and anodized aluminum alloy frame. Products have high efficiency, lifespan
easy installation, high wind resistance etc.
Products are made according to international standard IEC61215-2016; IEC61730-2016 and have passed
authority test center's examination. Our products can be used in home roof solar systems, PV stations,
communication stations, petrol, ocean, meteorological, traffic and solar building etc.
Information for installers
Installers must read and understand this manual before installation.
Please ensure that installation, operation and maintenance of your photovoltaic system is only carried
out by qualified persons able to carry out the technical procedures described in this manual, i.e. system planers,
installers and maintenance personnel, and is carried out in accordance with all safety precautions in this manual
and any and all applicable local codes. If you do not possess these qualifications, you may not carry out the work
described herein except for cleaning.
This manual and the instructions set forth herein are part of the product and should therefore be kept for
the entire useful life of the solar installation.
Information for operators
Keep these instructions safe for the entire useful life of the solar installation.
Please contact your plant supplier for information concerning the formal requirements for solar systems.
Please be sure to learn about directives and permit requirements from the responsible local authorities and
energy providers prior to installation of the solar plant.
We recommend that you insure your solar system against natural hazards (e.g. against lightning strikes).
正信光电科技股份有限公司
ZNSHINE PV-TECH CO.,LTD
Mounting Manual
P a g e
1 | 14
Advertisement
Related Manuals for Znshine Solar ZXM6-H144
Summary of Contents for Znshine Solar ZXM6-H144
- Page 1 正信光电科技股份有限公司 ZNSHINE PV-TECH CO.,LTD Mounting Manual INSTALLATION INSTRUCTION FOR SINGLE GLASS SOLAR MODULE ingle glass solar modules are made of 120/132/144/pcs of 158.75mm×79.375mm crystalline solar cells in series with high efficiency, high transmission and low iron toughened glasses , anti-aging EVA and high flame- resistant back sheet to laminate, and anodized aluminum alloy frame.
- Page 2 1、 Electrical Specification Mono/Poly-Si series PHOTOVOLTAIC MODULE ZXM6-H144 ZXP6-H144 ZXM6-H132 ZXP6-H132 ZXM6-H120 ZXP6-H120 Model Max series fuse rating(A) Nominal Mass 22.5kg/21.5kg 21kg/20.5kg 20.5kg/19.5kg 2000x992x40/35 2024x1002x40/35 1844x992x40/35 1675x992x40/35 2020x1002x40/35 1860x1002x40/35 1696x1002x40/35 Package Size（mm） 2040x1002x40/35 158.75x79.375/156.75x78.37 Cell Size(mm) DC1500V System voltage Class A...
-
Page 3: Operating Environment
● The electrical characteristics are within ±3 percent of the indicated values of Isc, Voc and Pmpp under test conditions (irradiance of 1000W/cm ,AM1.5 spectrum, and a cell temperature of 25℃) ●Under normal conditions, a photovoltaic module is likely to experience conditions that produce more current and/or voltage than reported at standard test conditions. - Page 4 ●The modules have passed mechanical load test 5400Pa,To avoid exceeding the maximum load, site- specific live loads such as wind and snow should be taken into account. ● The installation of project must be facing north in the southern hemisphere, and facing south in the northern hemisphere, the electricity will be comparatively lower when the project facing west or east.
- Page 5 ● Use the holes(5.0mm) marked ' '. To create the conductive connection (frame is anodized), use Stainless steel M5nut, two Stainless steel cut washer, Stainless steel M5 plain washer, Stainless steel M5 spring washer , M5 copper wire ,and Stainless steel M5 bolt. 1.
-
Page 6: Installation Direction
6、Mounting （A） Fixation with screws The frame of each module has 8-φ9*14mm mounting holes, used to secure the modules to support structure. Always use all the eight mounting holes to secure the modules. The module installed with screws on the front frame for load (see the following picture), and refer to the following table. Mechanical load Installation direction pressure... - Page 7 Modules must be securely attached to the mounting structure using pre-drilled mounting holes in the frame. Modules should be bolted to support structures through mounting holes located in the frame's back flanges only. Do not drill additional holes. Doing so will void the warranty. ...
- Page 8 Use a torque wrench for installation, and the compression for each clamps is not strong to avoid potential damages to module frames. The recommended maximum compression for each clamp is 20MPa (2900PSI). The module mounting structure must be made of durable, corrosion-resistant and UV-resistant material. All mounting hardware (bolt/flat washer/split washer/nut) should be stainless steel M8 size.
-
Page 9: Maintenance And Cleaning
The plug connector has its own polarity. Make sure that the connection is safe and tight. The plug connector should not receive outer stress. Otherwise, it is only used to connect the circuit! ● Use of suitable material Use cable extensions and plugs that are designed for outdoor application. Ensure that they are in perfect electrical and mechanical condition. - Page 10 10、Danger of death from electric shock! Solar modules generate electricity as soon as they are exposed to light. One module on its own is below the safety extra low volt level, but multiple modules connected in series (summing the voltage) or in parallel (summing the current) represent a danger.
- Page 11 ZX X X XX XX XX XXXX flow coding (4digit) 第 11.12 位数字码 production date (2digit)Two numbers minus 12 is the actual date 第 9、10 位数字码 production month (2digit)Two numbers minus 18 is the actual month 第 7、8 位数字码 Producing year (2digit)Two numbers minus 15 is the actual year 第...
- Page 12 Monocrystalline Silicon Module Module Series 尺寸（mm）/重量（kg） 2024*1002*40/35 Dimensions(mm)/ Weight(kg) 系统电压（VDC） 1500 Max-System Voltage (VDC) 最大保险丝额定电流（A） Max-Series Fuse(A) 电气参数（标准测试条件下） Electrical Performance @ STC ZXM6- ZXM6-H144- ZXM6-H144- ZXM6-H144- 组件类型 H144- 395/M 400/M 405/M 390/M Model Type 最大功率 Max-Power Pm(W) 最大功率点的工作电压 40.6 40.8 41.2...
- Page 13 最大功率点的工作电流 9.54 Max-Power Current I 开路电压 44.52 45.3 Open Circuit Voltage Voc(V) 开路电流 10.06 10.4 Short Circuit Current Isc(A) 组件系列 120pcs 158.75× 158.75mm Monocrystalline Silicon Module Module Series 尺寸（mm）/重量（kg） 1696*1002*40/35 Dimensions(mm)/ Weight(kg) 系统电压（VDC） 1500 Max-System Voltage (VDC) 最大保险丝额定电流（A） Max-Series Fuse(A) 电气参数（标准测试条件下）...
- Page 14 最大功率 Max-Power Pm(W) 最大功率点的工作电压 34.8 35.4 Max-Power Voltage V 最大功率点的工作电流 9.06 9.33 Max-Power Current I 开路电压 42.9 43.5 Open Circuit Voltage Voc(V) 开路电流 9.35 9.59 Short Circuit Current Isc(A) 组件系列 120pcs 156.75× 156.75mm Polycrystalline Silicon Module Module Series 尺寸（mm）/重量（kg） 1675x992x40/35 Dimensions(mm)/ Weight(kg) 系统电压（VDC）...