Table of Contents
Advertisement
Quick Links
Owner's/Installation Manual
50A Smart Management Module
Para español , visita:
http://www.generac.com/service-support/product-support-lookup
Pour le français, visiter :
http://www.generac.com/service-support/product-support-lookup
SAVE THIS MANUAL FOR FUTURE REFERENCE
Owner's/Installation Manual for SMM
(SMM)
MODEL: G007000-0
DATE PURCHASED:______________
WARNING
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.
WWW.GENERAC.COM
1-888-GENERAC
(1-888-436-3722)
000922
(000209b)
®
i
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Generac Power Systems SMM
Summary of Contents for Generac Power Systems SMM
- Page 1 Failure to adhere to this warning could result in death or serious injury. (000209b) WWW.GENERAC.COM 1-888-GENERAC (1-888-436-3722) Para español , visita: http://www.generac.com/service-support/product-support-lookup Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup SAVE THIS MANUAL FOR FUTURE REFERENCE Owner’s/Installation Manual for SMM...
- Page 2 WARNING CANCER AND REPRODUCTIVE HARM www.P65Warnings.ca.gov. (000393a) Owner’s/Installation Manual for SMM...
-
Page 3: Table Of Contents
Safety Rules ............1 General Hazards ..........1 Section 2: General Information and Setup Load Management Options .........3 Application Considerations ........3 Smart Management Module (SMM) ....3 SMM and Carton Contents ........4 Setting Lockout ............5 Jumper Locations ..........5 Section 3: Installation, Tests, &... - Page 4 Table of Contents This page intentionally left blank. Owner’s/Installation Manual for SMM...
-
Page 5: Section 1: Introduction And Safety
Observe Thank you for purchasing a Generac Smart Management them carefully. Alert definitions are as follows: Module (SMM). SMMs are designed to work together to prevent the home standby generator from being over- DANGER loaded by large appliance loads. - Page 6 Introduction and Safety This page intentionally left blank. Owner’s/Installation Manual for SMM...
-
Page 7: Section 2: General Information And Setup
5 minutes 30 seconds a preset value for a predetermined time. 5 minutes 45 seconds A SMM can be used individually or in conjunction with a SACM to manage a combined total of eight loads. SMMs 6 minutes operate independently when used in conjunction with the 6 minutes 15 seconds SACM. -
Page 8: Smm And Carton Contents
Priority Decal (G) – Provided for recording priority of Table 2-2. each module in installation. Install on electrical panel. NOTE: Recovery time is based on priority dial settings. Table 2-1. 000106 Figure 2-1. SMM Features and Controls Owner’s/Installation Manual for SMM... -
Page 9: Setting Lockout
NOTE: Change in jumper (4) is only required for specific applications and should not be moved under normal cir- SMMs are equipped with a lockout provision. The SMM cumstances. If unit is installed in an area with unstable can be set to enable LOCKOUT mode if load is identified... - Page 10 NOTE: Actual test time varies depending on SMM priority setting. Use the Utility following formula to calculate test time: Time = (P-1) x 15 seconds, where P represents priority setting. Example: SMM Priority 6 test time = (6-1) x 15 seconds, or 75 seconds. Owner’s/Installation Manual for SMM...
- Page 11 General Information and Setup Figure 2-3. SMM Sequence of Operations Owner’s/Installation Manual for SMM...
- Page 12 General Information and Setup This page intentionally left blank. Owner’s/Installation Manual for SMM...
-
Page 13: Section 3: Installation, Tests, & Troubleshooting
NEMA 3R rating and protect or stray voltage readings. See DMM manufacturer’s liter- against water ingress. ature for additional information. Continued on next page Owner’s/Installation Manual for SMM... -
Page 14: Connections
Black (240 VAC - Load) Depth (in/mm) 3.7 / 94 White - Neutral (as required) 5. Install SMM enclosure to mounting surface using Green - Ground (as required) appropriate mounting screws or wall anchors. Black - Factory (PCB) Red - Factory (PCB) -
Page 15: Setting Priorities
Priority 7 - Other circuits Priority 4 - Clothes Dryer Priority 8 - Other circuits 1. Set the priority of each SMM as desired (using the example configuration for reference). 2. Apply priority decal in a suitable location on electri- cal panel to record chosen priority designations. -
Page 16: Troubleshooting
Contact IASD for details. Load not powered while on Wiring or unstable frequency. Check wiring. See Setting Lockout for information utility on unstable frequency. Owner’s/Installation Manual for SMM... - Page 17 Installation, Tests, & Troubleshooting This page intentionally left blank. Owner’s/Installation Manual for SMM...
- Page 18 Installation, Tests, & Troubleshooting This page intentionally left blank. Owner’s/Installation Manual for SMM...
- Page 20 ©2019 Generac Power Systems, Inc. All rights reserved. Generac Power Systems, Inc. Specifications are subject to change without notice. S45 W29290 Hwy. 59 No reproduction allowed in any form without prior written Waukesha, WI 53189 consent from Generac Power Systems, Inc. 1-888-GENERAC (1-888-436-3722) www.generac.com...