Page 2
Kambic d.o.o. Kambic d.o.o. shall in no event be liable for incidental or consequential damages, including without limitations, lost profits, loss of income, loss of business opportunities, loss of use, and other related exposures, caused by incorrect use of product.
User Manual OBM-LT CONTENT 1. WARNINGS AND SAFETY PRECAUTIONS... 2. INTRODUCTIONS ..........3. TECHNICAL DATA ..........3.1 Front view............. 3.2 Rear view ............. 3.3 Top view ............... 4. INSTRUCTIONS FOR USE ........4.1 Basic Setup ............4.2 Control Panel with OLED display and keyboard ..
In no event shall Kambic d.o.o. be held liable for any damages, direct or incidental related to the use of this product and manual. Product can be equipped with variety of accessories and options. This warning list might include elements that are applicable only with certain models and accessories.
Page 5
User Manual OBM-LT WARNING Never use with toxic, corrosive, flammable or organic materials unless special precautions are in place to prevent injury to personnel or damage to equipment. WARNING Never operate the appliance with the housing removed! RISK OF FAILURE...
User Manual OBM-LT INTRODUCTIONS Calibration bath OBM-LT was developed and manufactured specifically for the calibration of temperature instruments, probes and liquid thermometers at temperatures from - 40°C to + 130°C. Fluid calibration baths ensure high temperature stability and uniformity across working volume.
User Manual OBM-LT TECHNICAL DATA OBM–LT Width 225 mm Height 638mm Depth 330 mm Working chamber dimensions 50 x 210 mm Volume ~ 1 L Temperature range - 40 °C …+ 130 °C Temperature Stability from ± 0.005 °C to ± 0.05 °C Better than ±...
User Manual OBM-LT 3.1 Front view Carrying handle Bath working chamber Rubber cap Control panel Front housing Back housing USB port Power cord connection RS 232 PC port Refrigeration system compartment – air intake Main switch Rubber legs 3.2 Rear view...
User Manual OBM-LT INSTRUCTIONS FOR USE 4.1 Basic setup Step 1: Remove rubber cap and fill the bath with appropriate fluid (up to 80%) Step 2: Connect the power cord into the power supply 230V±10%; 50Hz Step 3: Put the main switch in position 1 (on the back of the device)
User Manual OBM-LT 4.2.1 Main screen (running) Main screen while cycle is running: Bath temperature Heating power Temperature status Current program number Setpoint temperature Stirrer speed in % 4.2.2 Main screen (not running) After button is pressed you see this screen:...
User Manual OBM-LT 4.2.3 Program selection and start The bath must be in Main screen (not running): Press button to enter Program Start Menu: Program number Program 0 is reserved for manual With buttons select desired program. Select from 0 to 10.
Page 13
User Manual OBM-LT When cycle has started you see this screen for manual program : Bath temperature Heating power Temperature status Current program Setpoint temperature Stirrer speed Bath temperature: current measured bath temperature is 19.85°C Heating power: current heater duty cycle...
Page 14
User Manual OBM-LT When cycle has started you see this screen for automatic program : Bath temperature Heating power Temperature status Current program Setpoint temperature Stirrer speed Step dwell time Step information Bath temperature: current measured bath temperature is 26.31°C...
User Manual OBM-LT 4.2.4 Menu and navigation Press button to enter MAIN MENU: The Main Menu includes three submenus: Program Setup, Instrument Setup and Service: Use navigation buttons to select and then press button to enter selected submenu. Press button to go back one level.
User Manual OBM-LT 4.3 Program Setup Use navigation buttons to select parameter and then press button to edit parameter. With buttons change value of parameter. To move cursor left and right use button. Press button to confirm or button cancel changes.
Page 17
User Manual OBM-LT Program: choose desire program number to edit settings - manual program, 1÷10 for automatic program). choose the required number of temperature steps Steps: (set range from to 10). choose Stirring: speed for stirrer for fluid mixing (set range from...
User Manual OBM-LT 4.4 Instrument Setup Use navigation buttons to select parameter and then press button to edit parameter. With buttons change value of parameter. To move cursor left and right use button. Press button to confirm or button cancel changes.
User Manual OBM-LT 4.4.2 Time and Date Set time and date: Time format: hh:mm:ss Date format: yyyy.mm.dd 4.4.3 System Parameters Setup system parameters. To change parameter you must first enter password: Default values Max SETP limit: 130°C Heat power limit:...
User Manual OBM-LT 4.4.6 Change Password For password setup first enter old password: The factory default password is 1000. Now you can enter now password: Confirmation screen for password has changed:...
User Manual OBM-LT 4.5 Service When you enter Service screen you see information of bath model, bath serial number, firmware version, operating hours and after service hours:...
Maintenance and service within the warranty period may only be performed by the authorized service person. Please advise Kambic in before alternation & modification. It is not allowed to change or rebuild any part of the construction without producer's written permit.
User Manual OBM-LT 5.1 Draining the Bath All our calibration baths are designed and equipped with tank drain plug for draining of the bath fluid. The location of the drain plug is at back of the bath. After drain screw back the plug.
User Manual OBM-LT REQUIRES SPACE AND CONECTIONS The appliance must be installed at least 100 mm away from the nearest wall. It must also be in a dry and well ventilated room. Additional space or relocation of the apparatus may be necessary when carrying out any maintenance or servicing.
User Manual OBM-LT SAFE USE AND SAFETY ELEMENTS It is not allowed to heat-up any material which could form explosive atmosphere. Do not store any fluids on top of the housing! Microprocessor controller has a special safety system which turns heaters off if temperature rises for more than 5 °C above set temperature.
User Manual OBM-LT DISMANTLING AND DISPOSAL This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.
User Manual OBM-LT ABBRIVATIONS TEMP chamber temperature SETPT set temperature heating power proportional–integral–derivative (control loop) light-emitting diode RS 232 standard communication interface Universal Serial Bus...