Advertisement
DO nOT force the drill by pulling down on the handle with excessive force.
8
DO nOT use on non magnetic materials.
8
DO nOT use on the same steel work as electric welders are being used.
8
2. inTRODUcTiOn
manufactured using high quality components for performance and reliability. Lightweight and compact made from heavy duty die cast
magnesium alloy. Fitted with a powerful magnet to ensure unit stays adhered at any angle. Includes safety fixing strap, 10mm twist drill chuck
and integrated coolant system to extend the life of cutters and increase the quality of the cut. designed for use in fabrication, construction and
other applications when drilling ferrous metal.
3. SPecificaTiOn
model no ................................................................mAG230V
Cable Length .................................................................. 2.5m
magnet .....................................................................140000n
maximum Annular Cutter Capacity ............................... 35mm
maximum Cutter depth ................................................ 50mm
motor Power ................................................................1500W
Weight ............................................................................ 10kg
no Load Speed .......................................................... 800rpm
Supply ............................................................... 230V ~ 50Hz
Consumables (not included)
neat Cutting oil ......................................................... NCO/5L
Soluble Cutting oil .................................................... SCO/5L
Pilot Pin .................................................................... mAGC.P
HSS magnetic drill C utters
12mm ...................................................................... mAGC12
13mm ...................................................................... mAGC13
14mm ...................................................................... mAGC14
16mm ...................................................................... MAGC16
18mm ...................................................................... mAGC18
20mm ...................................................................... mAGC20
22mm ...................................................................... mAGC22
24mm ...................................................................... mAGC24
25mm ...................................................................... mAGC25
4. aSSeMbLy
4.1.
fiT cOOLanT bOTTLe Refer to fig.1
4.2.
Slacken the 2 thumbscrews and slide bottle cage over the
thumbscrews. Tighten thumbscrews.
4.2.1.
Connect coolant pipe to the valve on the drill head, fig.1.
Pipe can be released by pushing in the blue valve.)
4.2.2.
Make sure the coolant tap is closed, fill the bottle with appropriate
lubricant.
4.3.
fiT cUTTing biT
4.3.1.
Wind drill head up to maximum height.
4.3.2.
Unwind the two grub screws, fig.2.6, in to secure the cutting bit.
5. OPeRaTiOn
5.1.
mark the position of the hole to be drilled on the workpiece.
5.2.
POSiTiOn THe DRiLL
5.2.1.
Connect to the mains supply. offer drill to workpiece and line up
with the previously marked hole.
WaRning! make sure there is nothing between the magnet
‰
and the workpiece befORe turning the magnet on.
nOTe: When using drill vertically use the level, fig.2.7.
5.2.2.
ensure the drill head is wound back away from the workpiece
before turning the magnet on.
5.3.
aTTacH DRiLL TO WORKPiece
5.3.1.
Turn the magnet on, fig.2.2. Wind the drill head down to the
workpiece and align the cutting head pin.
5.4.
fiT THe SafeTy STRaP
5.4.1.
Place the safety strap though the handle of the drill and around
the steelwork. Adjust the length of the strap so that if the drill should
fall the drill should not be allowed to swing too far and be damaged.
5.5.
fiLL cOOLanT bOTTLe
5.5.1.
Always use the correct cutting oil, refer to Section 3 and refill once
it empties. never use without coolant.
5.6.
cUTTing THe HOLe
5.6.1.
Turn on the cooling tank tap, fig.1.
5.6.2.
Back the cutting head away from the workpiece, turn the drill
motor on, fig.2.1. Check the drill sounds and is operating normally.
© Jack Sealey Limited
fig.1
fig.2
1 motor switch
2 magnet switch
3 Handle
4 Fuse cover
5 Slide adjusters (5 each side)
6 Cutting bit grub screw (2 of)
Original Language Version
7 Level
8 Fuse cover (2 of)
mAG230V | Issue:1 18/12/18
Advertisement
