Related Manuals for Bushranger MC-S-2
Summary of Contents for Bushranger MC-S-2
- Page 1 Straight Shaft Attachment MC-S-2 Owner’s/ Operator’s Manual Completely read and understand this manual before using this product.
-
Page 2: Table Of Contents
It is essential that any operator of this Multi-cutter reads and understands the contents this manual before using the Multi-cutter. For additional assistance, contact any local authorized BUSHRANGER dealer. Important Notice The benefits to the consumer given by this warranty are in addition to other rights and remedies of the con- sumer under a law in relation to the goods or services to which this warranty relates. -
Page 3: Safety Instructions
5. Inspect the tool attachment and replace any parts that are cracked, chipped or damaged before using the Multi-cutter. 6. Never use a tool attachment or replacement parts that are not approved by BUSHRANGER. 7. Maintain the Multi-cutter according to the recommended maintenance intervals and procedures in the Maintenance section beginning on page 12. -
Page 4: Fuel Safety
9. Keep a firm footing and balance. Do not overreach. 10. Use the right tool for the job. Do not use the Multi-cutter for any job that is not recommended by BUSHRANGER. ＿ 3 ＿... -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any that are damaged or lost. ON SHAFT （Part No. 221501） ON SHAFT （Part No. 221502） ON SHAFT （Part No. -
Page 6: Assembly
Assembly Installing Guard WARNING M5X30 Screw(2) POTENTIAL HAZARD ・ Foreign objects can be thrown by Multi-cutter. WHAT CAN HAPPEN Gearcase ・ Contact with thrown objects can cause personal injury. Shaft Assembly HOW TO AVOID THE HAZARD ・ Never operate the Multi-cutter without the blade guard. Guard Plate 1. -
Page 7: Brushcutter Blade
Brushcutter Blade WARNING POTENTIAL HAZARD ・ If the Brushcutter Blade is not adequately tightened, it can come loose from the Straight Shaft Attachment during use. WHAT CAN HAPPEN ・ This may cause damage to property or personal injury. HOW TO AVOID THE HAZARD ・... -
Page 8: Attaching And Detaching For The Power Unit And The Shaft Assembly
Attaching and Detaching for the Power Unit and the Shaft Assembly Attaching Shaft Coupler First, loosen the clamping knob before Positioning attaching the shaft assembly to the shaft cou- Lever pler. Note: Do not over loosen the clamping Positioning Hole knob or it may fall out. -
Page 9: Idle Speed Adjustment
Keep hands and body away from the cutting attachment. If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the engine stalls, stop using the Multi-cutter immediately! Contact your local authorized BUSHRANGER Dealer for assistance and servicing. ＿ 8 ＿... -
Page 10: Operation
Operation WARNING POTENTIAL HAZARD ・ Foreign objects can be thrown by the Multi-Cutter. WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. HOW TO AVOID THE HAZARD ・ Never operate the Multi-Cutter without the blade guard in place. CAUTION ・... - Page 11 ・ If the trimmer head becomes jammed, stop the engine immediately. ・ Make certain all moving parts have stopped and disconnect the spark Pull plug before inspecting the equipment for damage. ・ Never use a unit that has a chipped, cracked or broken trimmer head. Red Band Shoulder Strap...
-
Page 12: Cutting Direction Of Brushcutter Blade
CORRECT INCORRECT Cutting Blades 1. Use only the correct blade (BUSHRANGER genuine part) approved for the application and model Brushcutter. 2. Carefully check the condition of the blades before and after operation. 3. Sharpen dull blades. Replace any blade that is worn, cracked or damaged. -
Page 13: Maintenance
・ Always turn off your Multi-Cutter before you clean or perform any maintenance on it. The BUSHRANGER Multi-Cutter will provide maximum performance for many, many hours if it is main- tained properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning the entire machine. -
Page 14: Specifications
Specifications MT262 with MC-S-2 Weight (kg) ※ 1 Engine Displacement (cm 25,4 Fuel Tank Capacity (L) Carburetor Diaphragm Type Ignition System Solid State Spark Plug NGK BPMR8Y Spark plug Gap (mm) 0,6-0,7 Fuel Mixture Two-stroke Oil Mix 50:1 Ratio MTK272 with... - Page 16 11 Sodium Street, Narangba Qld 4504 P/N.242010-01 GB 1909 IN...