Related Manuals for Bushranger MC-HTS-2
Summary of Contents for Bushranger MC-HTS-2
- Page 1 Hedge Trimmer Attachment MC-HTS-2 MC-HTSX-2 Owner’s/ Operator’s Manual Completely read and understand this manual before using this product.
-
Page 2: Table Of Contents
It is essential that any operator of this Multi-Cutter reads and understands the contents this manual before using the Multi-Cutter. For additional assistance, contact any local authorized BUSHRANGER dealer. Important Notice The benefits to the consumer given by this warranty are in addition to other rights and remedies of the con- sumer under a law in relation to the goods or services to which this warranty relates. -
Page 3: Safety Instructions
5. Inspect the tool attachment and replace any parts that are cracked, chipped or damaged before using the Multi-Cutter. 6. Never use a tool attachment or replacement parts that are not approved by BUSHRANGER. 7. Maintain the Multi-Cutter according to the recommended maintenance intervals and procedures in the Maintenance section beginning on page 9. -
Page 4: Fuel Safety
Keep all parts of your body away from the moving tool attachment and hot surfaces such as the muffler. 9. Keep a firm footing and balance. Do not overreach. 10. Use the right tool for the job. Do not use the Multi-Cutter for any job that is not recommended by BUSHRANGER. ＿ 3 ＿... -
Page 5: Safety And Instruction Decals
• Wear ear protection, while operating the Hedge Trimmer Attachment. Do not put hands near or under moving blades. Guaranteed sound power level 108 dB(A) . Product Description MC-HTS-2 1. Cutting Blades 2. Gearcase 3. Angle Drive 4. Shaft Assembly 5. -
Page 6: Assembly
Assembly Installing Shaft Assembly and Angle drive Driveshaft Attach the shaft assembly to the hedge trimmer angle drive assembly. Shaft Assembly NOTE: Carefully inspect both side of the shaft assembly. Locating Hole The arrow marking side of the shaft assembly positions to the power unit. -
Page 7: Idle Speed Adjustment
Keep hands and body away from the cutting attachment. If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the engine stalls, stop using the Multi-Cutter immediately! Contact your local authorized BUSHRANGER Dealer for assistance and servicing. ＿ 6 ＿... -
Page 8: Operation
Operation CAUTION ・ Read the Safety instructions beginning on page 2 concerning proper use of the Multi-Cutter. Operating Position Before using the Multi-Cutter with Hedge Trimmer Attachment, check the following: 1. The unit should be on operator’s right side. 2. The operator’s right hand should be holding the shaft grip, with his or her fingers on the throttle trigger. The right arm should be slightly bent. - Page 9 Adjusting the angle of the blades CAUTION ・ Do not touch the sharpened edges of the cutting blades. The cutting blades are extremely sharp and dangerous. Always wear gloves to help protect your hands and fingers from injury. ・ Do not hold any part other than the handle when adjusting the angle of the blades. ・...
-
Page 10: Maintenance
Maintenance Adjusting Cutting Blades CAUTION ・ Do not touch the sharpened edges of the cutting blades. The cutting blades are extremely sharp and danger- ous at all times. Maintenance Interval Before operating the Multi-Cutter with Hedge Trimmer Attachment it is necessary to check the adjustment of the cutting blades. -
Page 11: General Cleaning And Tightening
・ Always turn off your Multi-Cutter before you clean or perform any maintenance on it. The BUSHRANGER Multi-Cutter will provide maximum performance for many, many hours if it is main- tained properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning the entire machine. -
Page 12: Specifications
Specifications MT262 with MC-HTSX-2 MC-HTS-2(16) MC-HTS-2(24) Weight (kg) ※ 1 Cutting Length(mm) 402,5 402,5 612,5 Engine Displacement (cm 25,4 Fuel Tank Capacity (L) Carburetor Diaphragm Type Ignition System Solid State Spark Plug NGK BPMR8Y Spark plug Gap (mm) 0,6-0,7 Fuel Mixture... - Page 13 MEMO...
- Page 14 MEMO...
- Page 15 MEMO...
- Page 16 11 Sodium Street, Narangba Qld 4504 P/N.241979-01 GB 1909 IN...
Need help?
Do you have a question about the MC-HTS-2 and is the answer not in the manual?
Questions and answers