Table of Contents
Advertisement
Evolution Series Air Conditioners
Class I Division 2 Groups A, B, C, & D Hazardous Locations or Nonhazardous Locations
OPERATION AND INSTALLATION MANUAL
*** IMPORTANT ***
PLEASE READ this manual and follow the instructions for safe and satisfactory installation and operation of this system.
Keep this manual for future reference. Some information may not apply to all systems.
1
Advertisement
Table of Contents
Related Manuals for Ice Qube Evolution series
Summary of Contents for Ice Qube Evolution series
- Page 1 Evolution Series Air Conditioners Class I Division 2 Groups A, B, C, & D Hazardous Locations or Nonhazardous Locations OPERATION AND INSTALLATION MANUAL *** IMPORTANT *** PLEASE READ this manual and follow the instructions for safe and satisfactory installation and operation of this system.
-
Page 2: Table Of Contents
Introduction ..................................3 Basic Unit Operation ..............................3 Preservation Instructions ............................... 4 Pre-Installation Test ............................... 5 Preparing the Enclosure ..............................6 Mechanical Installation Instruction ..........................6 Electrical Installation Instruction ..........................8 Alarm Installation Instruction ............................. 10 Operating Your System ..............................11 Programming the Standard Controller ........................ -
Page 3: Introduction
The closed-loop cold air supply stream circulates cold air from the Ice Qube TMS to your electronics enclosure. This air returns to the Ice Qube TMS bringing with it unwanted heat and humidity from inside your enclosure. Heat and humidity is then removed by a heat exchanger which is part of the vapor-compression refrigeration system. -
Page 4: Preservation Instructions
Handling Ice Qube recommends that the unit remains in the proper upright position, as indicated on the shipping container. The unit must remain upright for a minimum of 24 hours before initial operation to ensure oil has returned to the compressor. -
Page 5: Pre-Installation Test
Before installing the Ice Qube system on your enclosure, Ice Qube recommends that the unit operates for 20-30 minutes to ensure it is functioning properly. Although the Ice Qube TMS has been tested at the factory, internal damage may have occurred during shipping which may have not been apparent during the unpacking inspection. -
Page 6: Preparing The Enclosure
After checking that all opening and bolt holes are in alignment, assemble and tighten the (2) ¼”-20 or 3/8”- 16 nuts and (4, 6 or 8 depending on model) ¼”-20 x 1” bolts supplied with you Ice Qube TMS by hand. - Page 7 Enclosure Side Ambient Side Figure 1: Enclosure Installation Figure 2: Push-to-Connect Fitting...
-
Page 8: Electrical Installation Instruction
Ice Qube TMS. Each Ice Qube TMS been designed to operate at a range of voltages and frequencies. See unit label(s) for correct voltage and frequency for your model(s). - Page 9 Figure 4: Terminal Block Figure 5: Power Terminal Block...
-
Page 10: Alarm Installation Instruction
Alarm Installation Instruction Ice Qube offers an optional alarm output that is provided through an alarm relay. This option is a dry contact (no voltage.) The alarm will be configured both normally open and normally closed. (X03) When the alarm output is supplied, a 120”(3048mm) cable with 3 flying leads, Common (Black), Normally Open (White), and Normally... -
Page 11: Operating Your System
The model may take 20 to 30 minutes before it achieves full capacity. If the heat load within the enclosure is less than the cooling capacity of the Ice Qube TMS, the temperature on the digital display will begin to decrease. When the temperature inside the enclosure decreases 7°F (4°C) below the “Cooling On”... - Page 12 Figure 7: Standard Controller To change the factory default settings, enter the programming code sequence below: “1 Adjust-up” arrow “2 Adjust-down” arrow “3 Select” “4 Exit” After pressing the above sequence the program LED should illuminate along with three alternating flashing boxes on the display face, indicating the code was accepted.
- Page 13 Press “3” to continue. The “Audible” LED will flash and the display will show “AUD”, indicating the audible alarm on/off status. Press “3” and the display shows “ON” or “OFF” indicating the current audible alarm status. Press “1” or “2” to toggle the mode desired. Press “3”...
-
Page 14: Programming The Ethernet Controller
With the ETMC, it is easy to connect the thermal management equipment to a network anywhere there is access to a node. Ice Qube ETMC has all the features of the standard digital controller, plus a user-friendly LCD message center, expanded temperature and alarm ranges, improved functionality, and the capability to communicate on an Ethernet network. -
Page 15: Maintenance
To check the condition of the air filter, it is recommended to remove electrical power from the Ice Qube TMS. Next, locate the filter. Slide the filter from the internal filter rack through the end slot and clean by soaking in warm soapy water. Rinse with clean water. Use a shop-vac to remove excess water from the filter before returning it to the system. - Page 16 No Is there adequate space around the air conditioner for airflow? Yes No Has the enclosure population remained the same? Notes: For additional support call: Ice Qube at 1-888-867-8234 Please have above checklist completed before you call.
-
Page 17: Schematic Wiring Diagrams
Schematic Wiring Diagrams Ordinary Locations 120V/220V/230V Figure 8 IQ350942 Rev A... -
Page 18: 400V/460V/480V
Ordinary Locations 400V/460V/480V Figure 9 IQ350943 Rev A... -
Page 19: Hazardous Locations
Hazardous Locations 120V/220V/230V Figure 10 IQ350921 Rev A... -
Page 20: 400V/460V/480V
Hazardous Locations 400V/460V/480V Figure 11 IQ350922 Rev A... -
Page 21: Specification Drawing
Specification Drawing 1000EV Figure 12... -
Page 22: 2000Ev
2000EV Figure 13... -
Page 23: 3000Ev
3000EV Figure 14... -
Page 24: 4000Ev
4000EV Figure 15... -
Page 25: 5000Ev
5000EV Figure 16... -
Page 26: 6000Ev
6000EV Figure 17... -
Page 27: 8000Ev
8000EV Figure 18... -
Page 28: 10000Ev
10000EV Figure 19... -
Page 29: 12000Ev
12000EV Figure 20... -
Page 30: 14000Ev
14000EV Figure 21... -
Page 31: 17000Ev
17000EV Figure 22... -
Page 32: 20000Ev
20000EV Figure 23... -
Page 33: Iq1-2-3000Ev Gasket And Cutout
IQ1-2-3000EV Gasket and Cutout Same Gasket and Cutout for IQ1000EV, IQ2000EV, and IQ3000EV Figure 24... -
Page 34: Iq4-5-6000Ev Gasket And Cutout
IQ4-5-6000EV Gasket and Cutout Same Gasket and Cutout for IQ4000EV, IQ5000EV, and IQ6000EV Figure 25... -
Page 35: Iq8-10-12000Ev Gasket And Cutout
IQ8-10-12000EV Gasket and Cutout Same Gasket and Cutout for IQ8000EV, IQ10000EV, and IQ12000EV Figure 26... -
Page 36: Iq14-17-20000Ev Gasket And Cutout
IQ14-17-20000EV Gasket and Cutout Same Gasket and Cutout for IQ14000EV, IQ17000EV, and IQ20000EV Figure 27... -
Page 37: Standard Warranty Policy
Products, damage to property, both real and personal, claims of third parties, including personal injury or death on account of use of the Products or failure of Ice Qube to warn against or instruct on or adequately warn against or instruct on, the dangers of the Products or the safe and proper use of the Products, whether or not customer has been advised of the potential for such damages. - Page 38 Products, damage to property, both real and personal, claims of third parties, including personal injury or death on account of use of the Products or failure of Ice Qube to warn against or instruct on or adequately warn against or instruct on, the dangers of the Products or the safe and proper use of the Products, whether or not customer has been advised of the potential for such damages.
- Page 39 QUBE, INC. Extended Warranty Options Ice Qube offers extended warranty options on a per Product basis. Please contact Ice Qube at (724) 837-7600 for further information. All extended warranties must comply with all applicable provisions of the Standard Warranty listed above.
- Page 40 Notes:...