Electric Actuator - Emerson Fisher D3 Instruction Manual

D3 Valve with easy-Drive Actuator
October 2017
Table 1. Specifications
Valve Body Sizes, End Connection Styles, and Port
(1)
Diameters
VALVE PORT
SIZE, DIAMETER,
NPS (INCHES)
1 0.375, 0.75, 1
2 0.375, 0.75, 1
X = Available construction.
Maximum Inlet Pressures and Temperatures
MAXIMUM INLET
PRESSURE
VALVE BODY SIZE
bar (psig)
155 (2250)
NPS 1 NPT
CL900 150 (2185)
155 (2250)
NPS 2 NPT
CL900
150 (2185)
103 (1500)
NPS 1 RF
CL600
100 (1455)
103 (1500)
NPS 2 RF
CL600
100 (1455)
Maximum Shutoff Pressure Drops
MAXIMUM nP BAR (PSI) PER PORT SIZE
Port Size,
9.5 (0.375)
mm (inch)
Flow Up 155 (2250)
Flow Down 155 (2250)
Shutoff Classification per ANSI/FCI 70‐2
and IEC 60534‐4
Class IV
Flow Characteristic / Valve Plug Style
Equal percentage / Micro‐Form Valve Plug
Maximum Travel
15 mm (0.6 inch)
Material Temperature Capabilities
Valve Body Assembly:
Standard Bonnet O-Ring: -40 to 135°C (-40 to 275°F)
Electric Actuator Assembly: -20 to 70°C
(-4 to 158°F), < 90% non-condensing humidity
Flow Direction
Flow up (standard), Flow down (optional)
1. The pressure or temperature limits in the referenced tables and any applicable ASME code limitations should not be exceeded.
2. 10% variation can be expected, based on temperature and pressure of application.
2
RAISED FACE
THREADED
(RF) FLANGED
CL900 CL600
X X
X X
(1)
TEMPERATURE RANGE
_C (_F)
-46 to 93 (-50 to 200)
93 to 149 (200 to 300)
-46 to 93 (-50 to 200)
93 to 149 (200 to 300)
-46 to 93 (-50 to 200)
93 to 149 (200 to 300)
-46 to 93 (-50 to 200)
93 to 149 (200 to 300)
(1)
19.1 (0.75) 25.4 (1.00)
105 (1518) 75 (1089)
155 (2250) 130 (1889)
(1)
Available Actuator Configurations
On/off (snap acting)
Positioning (flow or pressure control)
Power Requirements
12 or 24VDC, minimum 4 amp power supply required
(fuse to 5 amps)
Maximum Current Draw
4 amps
Idle Current Draw
38 mA
Conduit Connections
Two 3/4 NPT connections
Stroke Length
FloPro controlled between 10mm (0.4 inch) and
15mm (0.6 inch)
(2)
Nominal Stroke Speed
3.9 mm/s (0.15 inch/s) at 24 VDC
2.2 mm/s (0.09 inch/s) at 12 VDC
Hazardous Area Approvals
CSA (C/US): Explosion­Proof Class I, Division 1,
Groups C and D, T6, Ex d IIA T6, Class I, Zone 1, AEx d
IIA T6
ATEX Flameproof - Gas:
II 2 G ,Ex d IIA T6
IECEx Flameproof - Gas: Ex d IIA T6
Enclosure Rating
Type 4X and IP66
Duty Cycle
50% maximum
Enclosure Material
Cast aluminum alloy with powder coat paint
Approximate Weight:
18 - 27 kg (39 - 60 lbs), depending upon construction
Instruction Manual
D103460X012