Page 1 User's Manual PORTÉGÉ A30-D Satellite Pro A30-D/R40-D/A40-D TECRA A40-D...
Page 2: Table Of Contents
The Keyboard ..................4-3 Using the AccuPoint ................4-6 Using the Fingerprint Sensor ............... 4-7 Optical disc drive .................. 4-9 CyberLink PowerDVD for TOSHIBA ........... 4-16 Battery ....................4-18 Wireless WAN Device (A30-D) ............4-24 Wireless WAN Device (A40-D) ............4-26 GPS Function ..................
Page 3 LAN ....................... 4-32 Memory media ..................4-34 Smart Card ................... 4-38 External Display .................. 4-39 TOSHIBA Hi-Speed Port Replicator III 180W/120W ......4-43 Security lock ..................4-45 Optional TOSHIBA Accessories ............4-45 Sound System and Video mode ............4-46 Chapter 5 Utilities and Advanced Usage Utilities and Applications ..............
Page 4: Chapter 1 Legal, Regulatory, And Safety
Copyright, Disclaimer and Trademarks Copyright © 2016 Toshiba Client Solutions Co., Ltd. All Rights Reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Page 5: Regulatory Information
® The Bluetooth word mark is a registered trademark owned by Bluetooth SIG, Inc. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are registered trademarks or trademarks of HDMI Licensing LLC in the United States and other countries. DTS, the Symbol, &...
Page 6 TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external RGB monitor port, Universal Serial Bus (USB 2.0 or 3.0) ports, HDMI™ out port and Headphone/Microphone jack.
Page 7 EMC (Electromagnetic Compatibility) standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards.
Page 8 Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Page 9 Additional information as required by Regulation (EC) 1275/2008 amended by Regulation (EU) 801/2013 implementing European Eco-Design Directive with regard to requirements for standby, off mode and networked standby electric power consumption of electrical and electronic household and office equipment can be found here: http://www.toshiba.eu/Eco-Design User's Manual...
Page 10 For more detailed information about the collection and recycling programmes available in your country, please visit our website ( www.toshiba.eu/recycling ) or contact your local council office or the retail outlet where you purchased the product. Disposal of batteries and/or accumulators...
Page 11 Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007, with phased deadlines to 2018. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation.
Page 12: Video Standard Notice
For more detailed information about recycling of this product, please visit our website ( http://www.toshiba-india.com ) or contact call center (1800-200-6768). These symbols might not stick depending on the country and region where you purchased.
Page 13: Energy Star® Program
If the model you purchased is compliant, it uses the ENERGY STAR logo and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer...
Page 14: Optical Disc Drive Safety Instructions
To prevent direct exposure to the laser beam, do not try to open the enclosure. Location of the Required Label (Sample shown below. Location of the label and manufacturing information might vary.) TOSHIBA SAMSUNG STORAGE TECHNOLOGY KOREA CORPORATION 14F, Bldg. No.102, Digital empire2, 486 Sin-dong, Yeongtong-gu, Suwon-si,...
Page 15: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the following general precautions and to note the cautions included in the text of the manual.
Page 16 Stress injury Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture, and lighting that can help reduce physical stress.
Page 17: Safety Icons
Moving the computer While the computer is designed for flexible day-to-day usage, you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation. Make sure all disk/disc activity has ended before moving the computer. Turn off (shut down) the computer.
Page 18 Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. A caution informs you that improper use of equipment or failure to follow instructions might cause data loss, equipment damage, or might result in minor or moderate injury.
Page 19: Chapter 2 Getting Started
This chapter provides an equipment checklist, and basic information to start using your computer. If you use an operating system that was not pre-installed by TOSHIBA, some of the features described in this manual might not function properly. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Page 20: Short Model Name
Right-click Click the right Touch Pad control button once. Right-click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left-click the mouse twice. Tap the touch screen twice (only for touch screen models).
Page 21 Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor might cause fire or damage to the computer possibly resulting in serious injury.
Page 22 When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in this User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug might hold an electrical charge and cause an electrical shock or minor bodily injury when touched.
Page 23 Connect the DC output plug of the AC adaptor to the DC IN 19V jack on your computer. Figure 2-3 Connecting the DC output plug to the computer (A30-D) Figure 2-4 Connecting the DC output plug to the computer (A40-D) 1.
Page 24 Open and close the display panel with reasonable care. Opening it vigorously or slamming it shut might damage the computer. Do not put your fingers in the gap between the LCD panel and battery pack when closing your LCD, otherwise your fingers might get hurt. Be careful not to open the display panel too far as this might put stress on the display panel’s hinges and cause damage.
Page 25: Getting To Know Windows
Figure 2-6 Turning on the power (A30-D) 1. Power button Product appearance depends on the model you purchased. Initial setup The Windows Startup Screen is the first screen displayed when you turn on the power. To install the operating system properly, follow the on-screen instructions on each screen.
Page 26 Windows taskbar By default, the bottom of the desktop is Windows taskbar. You can see all of your currently running apps on the Windows taskbar. Task view Task view ( ) is launched from Windows taskbar at the bottom of the screen.
Page 27: Turning Off The Power
You can search for and browse thousands of apps, all grouped into easy- to-find categories there. Windows Hello Windows Hello is a more personal and secure way to sign in to your Windows system, apps, and services using fingerprint recognition. To set up Windows Hello, click Start ->...
Page 28 Make sure all disk/disc activity has stopped before removing the disk/ disc. If you turn off the power while a disk (disc) is being accessed, you might lose data or damage the disk. Never turn off the power while an application is running. Failure to do so can cause data loss.
Page 29 Note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the TOSHIBA System Settings. If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.
Page 30 When the computer is in Sleep Mode, the Power indicator blinks amber. If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode. Sleep Mode consumes more power while the computer is off. Sleep Mode limitations Sleep Mode will not function under the following conditions: Power is turned back on immediately after shutting down.
Page 31: System Recovery
Restoring the pre-installed software from your created Recovery Media Restoring the pre-installed software from the Recovery Partition If you choose TOSHIBA Maintenance Utility to erase the internal storage drive, all data including the operating system and recovery partition will be User's Manual...
Page 32 In that case, you cannot create recovery media or restore the pre- installed software from the recovery partition. Make sure that you have already created recovery media before you start TOSHIBA Maintenance Utility. This recovery media can be used to restore your system after you have erased your internal storage drive.
Page 33 Do not close the display panel during the restoring process. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. Make sure to use the default Boot Mode option in TOSHIBA Setup Utility before restoring. Launch the TOSHIBA Setup Utility.
Page 34 Recovery Media. However, if you have already created a "Recovery Media", you can use it to restore the recovery partition. If you have not created "Recovery Media", contact TOSHIBA support for assistance. Restoring the pre-installed software from the Recovery Partition A portion of the total internal storage drive space is configured as a hidden recovery partition.
Page 35 (Power) and then select Restart. Hold down 0 (zero) key and then release this key just after the computer is power on. Select Troubleshoot -> TOSHIBA Maintenance Utility -> TOSHIBA Recovery Wizard. Follow the on-screen instructions to finish the recovery.
Page 36: Chapter 3 The Grand Tour
Chapter 3 The Grand Tour This chapter identifies the various components of the computer. It is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, refer to the Legal Footnotes section.
Page 37 DC IN/Battery The DC IN/Battery indicator shows the indicator condition of the DC IN and the battery charge status. White indicates that the battery is fully charged while the power is being correctly supplied from the AC power adaptor. Refer to the Power Condition Descriptions section for more information on this feature.
Page 38 Figure 3-2 The left side of the computer (A30-D) 1. DC IN 19V jack 4. Optical disc drive* 2. LAN jack 5. Smart Card slot* 3. Universal Serial Bus (USB 3.0) port * Provided with some models. Product appearance depends on the model you purchased. DC IN 19V jack The AC adaptor connects to this jack in order to power the computer and charge its internal...
Page 39 Note that it is not possible to confirm the operation of all functions of all USB devices that are available. Some functions associated with a specific device might not operate properly. Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove.
Page 40 Universal Serial Bus Two Universal Serial Bus ports, which comply to (USB 3.0) ports the USB 3.0 standard, are provided on the right side of the computer. USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode.
Page 41 Back (A30-D) The following figure shows the back of the computer. Figure 3-4 The back of the computer (A30-D) 1. Battery pack Product appearance depends on the model you purchased. Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected.
Page 42 180W/120W. Some models are equipped with the docking port. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is compatible with the docking port. Do not attempt to use any other Port Replicator. Keep foreign objects out of the docking port. A pin or similar object can damage the circuitry of the computer.
Page 43 10. AccuPoint* 3. Microphone* 11. AccuPoint control buttons* 4. Web Camera* 12. Touch Pad ON/OFF icon 5. Web Camera LED* 13. TOSHIBA eco icon 6. Display screen 14. Touch Pad 7. Power button 15. Touch Pad control buttons 8. Display hinges 16.
Page 44 Wireless Depending on the configuration of your communication computer, one or all of the following antennas are antennas built-in: Wireless LAN ® Wireless LAN/Bluetooth Some models are equipped with wireless communication antennas. Do not cover the wireless communication antennas area with any metal objects, otherwise the wireless function might not work.
Page 45 AccuPoint are equipped with AccuPoint control buttons. Touch Pad ON/OFF Double tap this icon to enable/disable the Touch icon Pad. TOSHIBA eco icon Double tap this icon to launch the TOSHIBA eco Utility. User's Manual 3-10...
Page 46: The Grand Tour For A40-D
Touch Pad The Touch Pad located in the palm rest is used to control the movement of the mouse pointer. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the mouse pointer to go. Touch Pad control The two buttons located on the bottom of the buttons...
Page 47 DC IN/Battery The DC IN/Battery indicator shows the indicator condition of the DC IN and the battery charge status. White indicates that the battery is fully charged while the power is being correctly supplied from the AC power adaptor. Refer to the Power Condition Descriptions section for more information on this feature.
Page 48 Optical disc drive The computer might be configured with a DVD Super Multi drive. Some models are equipped with an Optical disc drive. 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to. Universal Serial Bus One Universal Serial Bus port, which complies to (USB 3.0) port the USB 3.0 standard, is provided on the left side of the computer.
Page 49 Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot. SIM Card slot This slot allows you insert a SIM card which enables a high-speed access to the Internet, corporate Intranet and your email while you are away from office.
Page 50 Universal Serial Bus Two Universal Serial Bus ports, which comply to (USB 3.0) ports the USB 3.0 standard, are provided on the right side of the computer. USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. The port with the icon ( ) has Sleep and Charge function, and this function is only provided with some models.
Page 51 LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics, for details.
Page 52 TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port Replicator III 180W/120W. Some models are equipped with the docking port. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is compatible with the docking port. User's Manual 3-17...
Page 53 Do not attempt to use any other Port Replicator. Keep foreign objects out of the docking port. A pin or similar object can damage the circuitry of the computer. Front with the display open (A40-D) This section shows the computer with the display panel open. In order to open the display, lift up the display panel and position it at a comfortable viewing angle for you.
Page 54 10. AccuPoint* 3. Microphone* 11. AccuPoint control buttons* 4. Web Camera* 12. Touch Pad ON/OFF icon* 5. Web Camera LED* 13. TOSHIBA eco icon* 6. Display screen 14. Touch Pad 7. Power button 15. Touch Pad control buttons 8. Display hinges 16.
Page 55 Wireless Depending on the configuration of your communication computer, one or all of the following antennas are antennas built-in: Wireless LAN ® Wireless LAN/Bluetooth Some models are equipped with wireless communication antennas. Do not cover the wireless communication antennas area with any metal objects, otherwise the wireless function might not work.
Page 56 Double tap this icon to enable/disable the Touch icon Pad. Some models are equipped with the Touch Pad ON/OFF icon. TOSHIBA eco icon Double tap this icon to launch the TOSHIBA eco Utility. Some models are equipped with the TOSHIBA eco icon. User's Manual 3-21...
Page 57: Internal Hardware Components
Touch Pad The Touch Pad located in the palm rest is used to control the movement of the mouse pointer. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the mouse pointer to go. Touch Pad control The two buttons located on the bottom of the buttons...
Page 58: Power Condition Descriptions
Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the HDD/SSD might be vulnerable to data retention errors. Legal Footnote (Internal Storage Drive Capacity) For more information regarding Internal Storage Drive Capacity, refer to the Legal Footnotes section.
Page 59 Power indicator Check the Power indicator to determine the power status of the computer. The following indicator conditions should be noted: White Indicates that power is being supplied to the computer, and the computer is turned on. Flashing Amber Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition.
Page 60: Chapter 4 Operating Basics
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that must be taken when using it. Using the Touch Screen (only for A30-D) Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the on- screen keyboard, and other items on the touch screen.
Page 61: Using The Touch Pad
Swipe Quickly move your finger in from the edge of the screen, without pausing when you first touch it. Swipe from the left edge: views all your open apps in task view. Swipe from the right edge: opens the Action center.
Page 62: The Keyboard
Three-Finger Swipe Quickly move in with three fingers together from the edge of the Touch Pad, without pausing when you first touch it. Swipe from the top edge: shows the desktop. Swipe from the bottom edge: views all your open apps in task view.
Page 63 Figure 4-1 CAPS LOCK indicator (A30-D) 1. CAPS LOCK indicator Product appearance depends on the model you purchased. CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. Function Keys The function keys (F1 ~ F12) are the12 keys at the top of your keyboard. Function keys let you enable or disable certain features of the computer.
Page 64 Some functions show the toast notification at the edges of the screen. Those toast notifications are enabled by default. You can disable them in the Function Key settings. To access it, click Start -> TOSHIBA -> System Settings -> Function Key. User's Manual...
Page 65: Using The Accupoint
Windows special keys The keyboard provides two keys that have special functions in Windows, ® the Windows logo key activates the Start menu while the application key has the same function as the secondary (right) mouse button. This key activates the Windows Start menu. This key has the same function as the secondary (right) mouse button.
Page 66: Using The Fingerprint Sensor
Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. You can buy replacement AccuPoint caps from your TOSHIBA authorized dealer. Using the Fingerprint Sensor Some models are equipped with the fingerprint sensor for the purpose of enrolling and recognizing fingerprints.
Page 67 The following illustrations show the recommended way to swipe your finger over the fingerprint sensor. Figure 4-3 Swipe the finger 1. Sensor Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping.
Page 68: Optical Disc Drive
Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry. Clean the sensor with a lint-free cloth. Do not use detergent or any other chemicals to clean the sensor. Avoid the following finger conditions for enrollment or recognition as they might result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate...
Page 69 Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL. Blu-ray™ Writer drive BDXL™ In addition to the above formats, Blu-ray™ Writer drive BDXL™ supports BD-ROM, BD-ROM DL, BD-R, BD-R DL, BD-RE, BD-RE DL,BD-R TL, BD- R QL and BD-RE TL.
Page 70 Lay the disc, label side up, in the disc tray. Figure 4-5 Inserting a disc (A30-D) 1. Laser lens Product appearance depends on the model you purchased. When the disc tray is fully opened, the edge of the computer covers the disc tray slightly.
Page 71 To pop the disc tray partially open, press the eject button. Gently pull the disc tray out until it is fully opened. When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. The disc extends slightly over the sides of the disc tray so you can grasp it.
Page 72 This might cause you to either lose data or incur other damage to the drive or media. Disclaimer TOSHIBA does not assume responsibility for the following: Damage to any disc that might be caused by writing or rewriting with this product.
Page 73 Based on TOSHIBA limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect write or rewrite success rates. Also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: MITSUBISHI KAGAKU MEDIA CO., LTD.
Page 74 BD-R DL: Panasonic Corporation BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: MITSUBISHI KAGAKU MEDIA CO., LTD. BD-RE TL: Panasonic Corporation Some types and formats of DVD-R DL and DVD+R DL discs might be unreadable. Disc created in DVD-R DL format4 (Layer Jump Recording) cannot be read.
Page 75: Cyberlink Powerdvd For Toshiba
Close all other applications when using the CyberLink PowerDVD for TOSHIBA. Do not open any other applications or carry out any other operations during video playback. Playback may stop or not function properly in some situations.
Page 76 The CyberLink PowerDVD for TOSHIBA does not have a parental control function. Carry out the installation/uninstallation of the CyberLink PowerDVD for TOSHIBA under a user account with administrator rights. Do not change Windows Users while CyberLink PowerDVD for TOSHIBA is running.
Page 77: Battery
Open CyberLink PowerDVD for TOSHIBA Manual CyberLink PowerDVD for TOSHIBA features and instructions are detailed in CyberLink PowerDVD for TOSHIBA Help. Use the following procedure to open CyberLink PowerDVD for TOSHIBA Help. Press the F1 key when CyberLink PowerDVD for TOSHIBA is launched.
Page 78 Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger. Charging Time (A30-D) The following table shows the approximate time required to charge an exhausted battery fully.
Page 79 Battery type Power off Power on Battery pack about 3.5 hours about 3.5 ~ 10 hours (45 Wh, 4 cell) RTC battery Does not Does not charge charge Charging Time (A40-D) The following table shows the approximate time required to charge an exhausted battery fully.
Page 80 The battery has not been used for a long time. The battery has completely discharged and been left in the computer for a long time. In such cases, do the following: Fully discharge the battery by leaving it in the computer with the power on until the system automatically turns itself off.
Page 81 The environmental temperature - operating time decreases at low temperatures System Sleep Mode System Hibernation Mode Display power off period Whether you enable Sleep Mode, which can conserve battery power if you are frequently turning the computer off and on The condition of the battery terminals.
Page 82 Connect the AC adaptor to the DC IN 19V jack of the computer, and to a wall outlet that is supplying power. The DC IN/Battery indicator glows amber to indicate that the battery pack is being charged. However, if DC IN/Battery indicator does not glow, this indicates that power is not being supplied.
Page 83: Wireless Wan Device (A30-D)
Figure 4-7 Releasing the battery pack (A30-D) 1. Battery lock 3. Battery pack 2. Battery release latch Product appearance depends on the model you purchased. Installing the battery pack To install a battery pack, do the following: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.
Page 84 To pop the SIM card tray partially open, insert a slender object (about 10mm, diameter 0.8mm), such as a straightened paper clip, into the eject hole. Gently pull to open the SIM card tray. Never pull the SIM card tray completely out of the slot. Figure 4-8 Open the SIM card tray with the eject hole (A30-D) 1.
Page 85: Wireless Wan Device (A40-D)
Wireless WAN Device (A40-D) Some models are equipped with the Wireless WAN device. This device gives you the ability for a high-speed connection to the Internet, corporate intranet, and your email while you are away from the office. Installing a SIM card (A40-D) To install a SIM card, do the following: Click Start ->...
Page 86: Gps Function
Install the battery pack. Figure 4-10 Installing the SIM Card (A40-D) 1. SIM card tray 2. SIM card Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
Page 87: Additional Memory Module (Only For A30-D)
When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions.
Page 88 Use a point size 0 Phillips screwdriver to remove and fasten the screws. The use of an incorrect screwdriver can damage the screw heads. Installing a memory module To install a memory module, do the following: Click Start -> (Power) and then click Shut down while holding down the SHIFT key.
Page 89 Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 4-12 Seating the memory module 1.
Page 90 Seat the memory module cover in place and secure it with the screw. Ensure that the memory module cover is firmly closed. Figure 4-13 Seating the memory module cover 1. Memory module cover 2. Screws Product appearance depends on the model you purchased. Install the battery pack.
Page 91: Lan
Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.
Page 92 The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on). LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings might cause a malfunction in LAN operation.
Page 93: Memory Media
Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 4-15 Connecting the LAN cable (A30-D) Figure 4-16 Connecting the LAN cable (A40-D) 1. LAN jack 2. LAN cable Product appearance depends on the model you purchased.
Page 94 Figure 4-17 Examples of memory media Secure Digital (SD) Card microSD card adaptor and microSD card MultiMediaCard (MMC) Points to note about the memory media card SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music.
Page 95 To format all areas of the memory card, including the protected area, you must obtain an appropriate application that applies the copy protection system. Media care Observe the following precautions when handling the card. Do not twist or bend cards. Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid.
Page 96 Press the memory media gently until it clicks into place. Figure 4-18 Inserting memory media (A30-D) Figure 4-19 Inserting memory media (A40-D) 1. Memory media slot 2. Memory media Product appearance depends on the model you purchased. Make sure that the memory media is oriented properly before you insert it.
Page 97: Smart Card
If you remove the memory media or turn off the power while the computer is accessing the memory media, you might lose data or damage the media. Do not remove the memory media while the computer is in Sleep or Hibernation Mode.
Page 98: External Display
Press the Smart Card gently to ensure a firm connection is made. The computer will identify the Smart Card and display an icon in the Windows Taskbar. When inserting a Smart Card into the Smart Card slot, make sure to confirm that the card is oriented correctly before inserting.
Page 99 External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer. To connect an external analog monitor, do the following: Connect one end of the RGB cable to the External RGB monitor port. Connect the other end of the RGB cable to the RGB port of the computer.
Page 100 Plug the other end of the HDMI™ cable into the HDMI™ out port on your computer. Turn the HDMI™ display device's power on. Figure 4-21 Connecting the HDMI™ out port (A30-D) 1. HDMI™ out port 2. HDMI™ cable Product appearance depends on the model you purchased. Do not plug/unplug an HDMI™...
Page 101 Wireless display Your computer might support wireless display, a wireless technology which ® utilizes Wi-Fi to allow the computer to be wirelessly connected to external displays including TVs as extended screens. With wireless display, documents, streamed/local media contents or other online contents can be shared wirelessly with others.
Page 102: Toshiba Hi-Speed Port Replicator Iii 180W/120W
TOSHIBA Hi-Speed Port Replicator III 180W/ 120W In addition to the ports available on the computer, the TOSHIBA Hi-Speed Port Replicator III 180W/120W also provides several kinds of ports. The Port Replicator connects directly to the docking interface on the underside of the computer.
Page 103 1. Docking port (computer) Product appearance depends on the model you purchased. Make sure the AC adaptor is always connected to the TOSHIBA Hi-Speed Port Replicator III 180W/120W while in use. Otherwise the Port Replicator will stop working, possibly resulting in data loss.
Page 104: Security Lock
1. Security lock slot 2. Security lock Product appearance depends on the model you purchased. Optional TOSHIBA Accessories To make your computer even more powerful and convenient to use, you can add a number of options and accessories. For reference, the following...
Page 105: Sound System And Video Mode
Battery section for further information. TOSHIBA Hi-Speed TOSHIBA Hi-Speed Port Replicator III 180W/ Port Replicator III 120W provides several kinds of ports. Refer to 180W/120W the Port Replicator’s User's Manual for more details.
Page 106 On the Enhancements tab, select the sound effects you would like, and click Apply. DTS Studio Sound™ DTS Studio Sound™ is a premium audio enhancement suite that utilizes revolutionary audio technology to provide the most immersive and realistic listening experience ever offered for a two speaker playback environment. DTS Studio Sound™...
Page 107 When audio power management is enabled, the circle button at the upper left of the Power Management is blue and convex. When audio power management is disabled, the button is black and concave. Speaker Configuration Click the Auto Test button to confirm the internal speakers or the headphone sound is coming from the right direction.
Page 108: Chapter 5 Utilities And Advanced Usage
PBA Setting in Password utility. Please note that Pre-Boot Authentication and Single Sign-On function will be disabled if TOSHIBA Password Utility is uninstalled. To access this utility, click Start -> TOSHIBA -> Password Utility. TOSHIBA System This utility allows you to customize your...
Page 109 Depending on the usage situation, the life cycle of the battery might not be extended properly. To access this utility, click Start -> TOSHIBA -> eco Utility. For details on TOSHIBA eco utility, see the help file.
Page 110: Special Features
You might not have all the software listed in this section depending on the model you purchased. Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. Access each function using the following procedures.
Page 111 Internal storage drive This feature automatically cuts off power to the internal storage drive when it is not accessed for automatic power off a specified time, with power being restored when the internal storage drive is next accessed. This can be specified in the Power Options. System automatic This feature automatically shuts down the system Sleep/Hibernation...
Page 112: Toshiba Password Utility
In this instance, all unsaved data in memory will be lost. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password. User's Manual...
Page 113 User Password To start the utility, click Start -> TOSHIBA -> Password Utility and click User Password. User authentication might be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords, and so on. Set (button) Click this button to register a password.
Page 114: Toshiba System Settings
To run TOSHIBA System Settings, click Start -> TOSHIBA -> System Settings. The TOSHIBA System Settings window contains a number of tabs to allow specific functions of the computer to be configured. In addition there are also three buttons: OK, Cancel and Apply.
Page 115: Usb Charge
OFF. "Power OFF" includes Sleep Mode, Hibernation Mode, or shutdown state. To set USB Sleep and Charge feature, click Start -> TOSHIBA -> System Settings -> Sleep Utilites. Move the slider to enable or disable the Sleep and Charge function.
Page 116 The Sleep and Charge function might not work with certain external devices even if they are compliant with the USB specification. In those cases, turn the power of the computer ON to charge the device. When Sleep and Charge function is enabled, USB bus power (DC5V) is supplied to compatible ports even when the power of the computer is turned OFF.
Page 117 Charge Mode" is enabled, your computer can supply USB bus power (DC5V, 1.5A) to the compatible ports while the computer is turned on. To set System ON CDP Charge Mode, click Start -> TOSHIBA -> System Settings -> USB. Enabled Rapid USB battery charge at maximum 1.5A...
Page 118: Using The Hard Disk Drive (Hdd) Protection
Setting up HDD Protection You can change HDD Protection settings. To open the utility, click Start -> TOSHIBA -> System Settings -> HDD Protection. The utility can also be started from the icon in the Taskbar or from the Control Panel.
Page 119 There are the following conditions for HDD Protection icon. Normal TOSHIBA HDD Protection is enabled. Protection TOSHIBA HDD Protection is active. The Hard Disk Drive head is in a safe position. TOSHIBA HDD Protection is disabled. Detection Level There are four sensitivity levels in which vibrations, impacts and their similar signs are detected can be set to OFF, 1, 2 and 3 in ascending order.
Page 120: Toshiba Setup Utility
Intensely shaking the computer or other subjecting it to strong impacts might damage to the computer. TOSHIBA Setup Utility TOSHIBA Setup Utility is a BIOS setup utility that provides you a menu- based user interface so that you can easily view and change BIOS settings.
Page 121: Troubleshooting
In reality many problems can be solved simply, but a few might require help from TOSHIBA Support. If you find you need to consult others, be prepared to describe the problem in as much detail as possible.
Page 122 Always try to make detailed notes of your observations and keep them in a permanent error log - this helps you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made helps to identify the problem faster.
Page 123 Before using a peripheral device or application software that is not an authorized TOSHIBA part or product, make sure that the device or software can be used with your computer. Use of incompatible devices might cause injury or might damage your computer.
Page 124: Hardware And System Checklist
By holding down one of the following keys during startup, your computer can load the following advanced options. Advanced option TOSHIBA Setup Utility Boot Menu 0 (zero) Recovery options If your computer starts to load the Operating System instead of desired advanced options, do the following: Click Start ->...
Page 125 If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact TOSHIBA Support. AC power If you have trouble turning on the computer with the AC adaptor connected, check the status of the DC IN/Battery indicator.
Page 126 However, if you do not believe the battery is at the end of its operating life, you should speak to TOSHIBA Support. Battery does not If you frequently recharge a partially charged...
Page 127 The RTC battery should be replaced only by your dealer or by a TOSHIBA service presentative, and then set the date/time in the TOSHIBA Setup Utility by using the following steps: Launch the TOSHIBA Setup Utility.
Page 128 Check to see whether there is a disc in the optical boot from internal disc drive - if so remove it and try to start the storage computer again. If this has no effect, check the Boot Priority Options setting within the TOSHIBA System Settings. User's Manual...
Page 129 As a last resort, you should reformat the HDD and then reload the operating system and all other files and data. If you are still unable to resolve the problem, contact TOSHIBA Support. Optical Disc Drive For further information, refer to Operating Basics.
Page 130 If you are still unable to resolve the problem, contact TOSHIBA Support. Pointing device If you are using a USB mouse, you should also refer to both the mouse section and the documentation supplied with your mouse.
Page 131 Control Panel -> Hardware and Sound -> sensitive enough. Mouse. If you are still unable to resolve the problem, contact TOSHIBA Support. USB mouse Problem Procedure Mouse pointer does In this instance, the system might be busy.Try...
Page 132 Sleep and Charge Enable the Sleep and Charge function in the function. TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply might be stopped for safety reasons.
Page 133 Problem Procedure The battery depletes If Sleep and Charge function is enabled, the quickly even when I computer's battery discharges during hibernation turned OFF the or when the computer is turned off. power of the Connect the AC adaptor to the computer or disable computer.
Page 134 Volume cannot be adjusted during Windows start up or shut down. If you are still unable to resolve the problem, contact TOSHIBA Support. External monitor Also refer to Operating Basics, and to the documentation supplied with your monitor for further information.
Page 135 Display error occurs Check that the cable connecting the external monitor to the computer is firmly attached. If you are still unable to resolve the problem, contact TOSHIBA Support. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub.
Page 136: Toshiba Support
TOSHIBA Support. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you might need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience might be related to software or the operating system so it is important that you investigate other sources of assistance first.
Page 137 - they are your best resource for current information and support. TOSHIBA technical support If you are still unable to solve the problem and suspect that it is hardware- related, read the enclosed warranty booklet or visit the TOSHIBA technical support website http://pc-support.toshiba.eu User's Manual...
Page 138: Appendix Specifications
Chapter 7 Appendix Specifications This section summarizes the technical specifications of the computer. Physical Dimensions (A30-D) The following physical dimensions do not include parts that extend beyond the main body. The physical dimensions vary depending on the model you purchased. Size Approximately 316 (w) x 229 (d) x 22.4 (h) millimeters Approximately 316 (w) x 229 (d) x 25.4 (h) millimeters (touch...
Page 139 Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum Power Requirements AC adaptor 100-240V AC 50 Hz or 60 Hz (cycles per second) Computer 19V DC External RGB monitor port pin assignment Signal Name Description Red Video Signal Green Video Signal...
Page 140: Ac Power Cord And Connectors
Signal Name Description Serial Clock Signal I/O (I): Input to computer I/O (O): Output from computer AC Power Cord and Connectors The AC input plug of the power cord must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used.
Page 141: Information For Wireless Devices
6-15P (250 V) or 5-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe, Middle-East, Africa, South Africa and China.
Page 142 Because wireless products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes wireless products are safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 143 If this occurs, the outsider might illegally access your system, eavesdrop, or cause the loss or destruction of stored data. TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Card Specifications Compatibility IEEE 802.11 Standard for Wireless LANs...
Page 144 Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4 GHz and 5 GHz band, local radio regulations might impose a number of limitations to the use of wireless communication equipment.
Page 145 Worldwide operation ® The Bluetooth radio transmitter and receiver operate in the 2.4 GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other.
Page 146 Restrictions for Use of 5150-5350MHz Frequencies in Europe Italy: For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. Luxembourg: Implemented General authorization required for network and service supply. Russian Limited e.i.r.p 100mW. Permitted to use Federation: only for indoor applications, closed industrial and warehouse areas,...
Page 147 Russian Limited e.i.r.p 100mW. Permitted to use Federation: only for indoor applications, closed industrial and warehouse areas, and on board aircraft. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight.
Page 148 The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 149 If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations.
Page 150 (1)(2) (3)(4) 2.4 : This equipment uses a frequency of 2.4 GHz. DS : This equipment uses DS-SS modulation. OF : This equipment uses OFDM modulation. 4 : The interference range of this equipment is less than 40 m. : This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz.
Page 151: Information About Intel® Amt
This equipment is approved to the radio standard by the countries/regions in the following table. If you use this equipment in the countries/regions which are not listed in the following table, contact TOSHIBA Support. As of November 2016 Austria Belgium...
Page 152 Disable the AMT function ® Intel AMT function is enabled by default, and in a situation where no system administrator presents, it is strongly recommended that you turn off the AMT function before connecting to a network. If the AMT function is NOT turned off, there is a danger that the management of AMT function will be abused by other parties which possibly lead to the leak of sensitive and/or proprietary information, data loss, HDD/SSD erasure, or file overwritten.
Page 153 Enter a new password. Password must comply with the following requirements concerning character types and length: Must be between 8 and 32 characters long. Must contain at least one number (“0”, “1-9”). Must contain a mix of lower-case (“a”, “b”, “z”, etc.) and upper-case (“A”, “B”, “Z”, etc.) letter.
Page 154: Information About Intel® Authenticate
When using the computer with the AC adaptor connected and the AMT function set to enabled, power might still be supplied to the system memory even when the computer power is turned off, or the computer is in Sleep Mode or Hibernation Mode. When connecting the AC adaptor, the computer is powered and can be turned on.
Page 155: Legal Footnotes
For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation. Contact TOSHIBA technical service and support, refer to TOSHIBA support section for more information.
Page 156 Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery might not charge while computer is consuming full power.
Page 157: Vcci Class B Information (Japan Only)
Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. Screen dims when the computer is operated on battery power and you might not be able to increase the brightness of the screen.
Page 158 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for...
Page 159 All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code;...
Page 160: Freetype License Issues
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.] FreeType License Issues...
Page 161 Portions of this software are copyright (C) <year> The FreeType Project www.freetype.org All rights reserved. """ Please replace <year> with the value from the FreeType version you actually use. Legal Terms ============ 0. Definitions -------------- Throughout this license, the terms `package`, `FreeType Project`, and `FreeType archive` refer to the set of files originally distributed by the authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project`, be they named as alpha, beta or final release.
Page 162 Redistribution of source code must retain this license file (`FTL.TXT`) unaltered; any additions, deletions or changes to the original files must be clearly indicated in accompanying documentation. The copyright notices of the unaltered, original files must be preserved in all copies of source files.
Page 163: Index
Index AccuPoint 4-6 Touch Pad 6-10 AC adaptor additional 4-46 connecting 2-3 DC IN 19V jack 3-3, 3-16 Equipment checklist 2-1 External monitor problems 6-14 Battery extending life 4-22 monitoring capacity 4-21 real time clock 3-23, 4-18 Hard disk drive save mode 5-4 automatic power off 5-4 types 4-18...
Page 164 6-5 inserting 4-36 Power 6-4 removing 4-37 Real Time Clock 6-7 Sound system 6-13 TOSHIBA support 6-16 Memory media slot 4-34 Touch Pad 6-10 USB device 6-12 Moving the computer 1-14 USB mouse 6-11 MultiMediaCard removing 4-37...
Page 165 Touch Screen 4-1 USB device problems 6-12 Video mode 4-48 Web Camera 3-9, 3-20 Wireless communication 7-6 User's Manual Index-3...

This manual is also suitable for:

Satellite pro a30-d Satellite pro r40-d Satellite pro a40-d Tecra a40-d

Toshiba portege A30-D User Manual

Chapter 1 Legal, Regulatory, and Safety

Chapter 2 Getting Started

Chapter 3 The Grand Tour

Chapter 4 Operating Basics

Chapter 5 Utilities and Advanced Usage

Chapter 6 Troubleshooting

Chapter 7 Appendix Specifications

Quick Links

Related Manuals for Toshiba portege A30-D

Summary of Contents for Toshiba portege A30-D

This manual is also suitable for:

Table of Contents