Table of Contents
Advertisement
Reprogramming of DVD version Matrix
After repair, the customer setting and region code may be lost.
Reprogramming will put the set back in the state in which it has left
the factory, ie. with the default setting and the allowed region code.
HTS5x00 Software Version Matrix
Key
Model
Sequence
Open
1
HTS5510C/75
Tray 9999
Audio 4
Open
2
HTS5510C/98
Tray 9999
Audio 5
To reprogram do as follows:
1) Power up the set and select DISC source.
2) Open tray by press "OPEN/CLOSE" button on the set or press
and hold "STOP" button on the RC.
3) Press the following buttons on the Remote Control:
<9> <9> <9> <9> <AUDIO> <4> ......... for HTS5510C/75
<9> <9> <9> <9> <AUDIO> <5> ......... for HTS5510C/98
4) The display shows 'YYYY-ZZ' and the tray will close.
YYYY = model number (eg. 8300, 8500, etc.)
ZZ
= slash stroke version (eg. 01, 69, etc.)
Procedure for check Software version
1) Power up the set and select DISC source.
2) Open tray by press "OPEN/CLOSE" button on the set or press
and hold "STOP" button on the RC.
3) Press "DISPLAY" button on the Remote control.
4) The TV screen will shows:
SD6.3 Vxx YYYY-ZZ A BB
SERVO: nnnnnnnn REG:A
xx
=
version number
YYYY
=
model number (eg. 8300, 8500, etc.)
ZZ
=
slash stroke version (eg. 01, 69, etc.)
A
=
region code
BB
=
Front uP software version number
nnnnnnnn
=
servo version number
Procedure to upgrade software
1) Power up the set and select DISC source.
2) Open tray by press "OPEN/CLOSE" button on the set or press
and hold "STOP" button on the RC.
3) Place Upgrade CD-ROM with fi lename "HTS5500.bin" onto tray
and close.
4) The set will response and display the following:
- LOAD
- ERASE
- WRITE
- ERROR
- UPG END
- DISC->CLOSE->LOAD
5) The whole process should not take more than 5 minutes.
Caution: Do not unplug the set until upgrade is completed.
Diagnostic Software
Region
TV
Region
Code
Type
Australia
4
PAL
AP
3
PAL
(After the disc is read, the tray will
open for you to remove the disc)
(Erasing disc)
(Writing disc)
(if upgrade is unsuccessful)
(if upgrade is successful)
(Tray will close indicating that the
upgrade process is completed)
HTS5510C/75/98
Trade Mode
Trade mode is a feature that will block all set keys when enabled.
It is for dealers to prevent customers from removing disc, changing
source etc using the set keys. Rotary and Remote Control (RC) keys
are still allowed inTrade mode.
To activate Trade Mode:
1) Power up the set and select DISC source.
2) Open tray by press "OPEN/CLOSE" button on the set
or press and hold "STOP" button on the RC.
3) Then press buttons <2> <5> <9> on the RC.
4) The display shows 'TRA ON' and the tray will close.
Trade Mode is now enabled.
To deactivate Trade Mode:
1) Power up the set and select DISC source.
2) Open tray by press and hold "STOP" button on the RC.
3) Then press buttons <2> <5> <9> on the RC.
4) The display shows 'TRA OFF' and the tray will close.
Trade Mode is now disabled.
Procedure to change Tuner Grid (not for all
versions)
In North and South America, the frequency step between adjacent
channels in the MW band is 10kHz (9kHz in some areas). The preset
frequency step in the factory is 9kHz.
IMPORTANT!
Changing the tuning grid will erase all previously stored preset
radio stations.
1) Press TUNER on the remote (or press SOURCE control on front
panel) to select "FM" or "MW".
2) Press STANDY ON to switch the DVD system to standby mode.
3) While holding down SOURCE and
disconnect and connect the power cord to the power supply
again.
-> The display will show "GRID 9" or "GRID 10".
Helpful hints:
- GRID 9 and GRID 10 indicate that the tuning grid is in step of
9kHz and 10kHz respectively.
- The FM tuning grid also will be changed from 50kHz to 100kHz
or vice versa.
3.
EN 11
PREV on the front panel,
Advertisement
Table of Contents
