EN 2 3139 785 31871 Technical Specifi cations and Connection Facilities LOCATION OF PC BOARDS HTS3100 VERSION VARIA TIONS: HTS3100 Type /Versions: Features & Progressive Scan Line-Out TV-In Aux-In Y/Pb/Pr (YUV) Component Video Output CVBS SCART...
Page 3
Technical Specifi cations and Connection Facilities 3139 785 31871 EN 3 1. Specifi cations General: AMPLIFIER: Mains voltage : 230V for /05, /12, /51 Output power 120V/230V for /55 Front : 25W RMS / channel Rear : 25W RMS / channel Mains frequency : 50/60Hz for /98, /55, Center...
EN 4 3139 785 31871 Measurements Setup, Service Aid & Lead Free Requirements 2. Measurements Setup, Service Aid & Lead Free Requirements MEASUREMENT SETUP Tuner FM Bandpass LF Voltmeter 250Hz-15kHz e.g. PM2534 e.g. 7122 707 48001 RF Generator e.g. PM5326 S/N and distortion meter e.g.
Page 5
Measurements Setup, Service Aid & Lead Free Requirements 3139 785 31871 EN 5 SERVICE AIDS Service Tools: Universal Torx driver holder ........4822 395 91019 Torx bit T10 150mm ..........4822 395 50456 Torx driver set T6 - T20 ......... 4822 395 50145 Torx driver T10 extended ........
Page 6
EN 6 3139 785 31871 Measurements Setup, Service Aid & Lead Free Requirements WAARSCHUWING WARNING Alle IC’s en vele andere halfgeleiders zijn All ICs and many other semi-conductors are gevoelig voor electrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan Careless handling during repair can reduce life de levensduur drastisch doen verminderen.
Page 7
Due to lead-free technology some rules have to be respected by the workshop during a repair: • Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-paste is required, please contact the manufacturer of your solder-equipment.
EN 8 3139 785 31871 Measurements Setup, Service Aid & Lead Free Requirements 2.2 Service Hints CAUTION CHARGED CAPACITORS ON THE SERVO BOARD MAY DAMAGE THE DRIVE ELECTRONICS WHEN CONNECTING A NEW DRIVE.THAT’S WHY, BESIDES THE SAFETY MEASURES LIKE • SWITCH OFF POWER SUPPLY •...
Dismantling Instructions & Service Positions 3139 785 31871 EN 11 Dismantling Instructions Dismantling of the DVD Loader Tray Cover Dismantling of the Front Board, PSU Module & DVD Loader. 1) Insert a minus screwdriver and push the lever in the direction as shown in Figure 4-1 to unlock the tray before 1) Release 4 snap hooks to remove the Front Board.
Page 12
EN 12 3139 785 31871 Dismantling Instructions & Service Positions Dismantling of the Tuner Module & Mono Dismantling of the Amp-module Board Board. 1) Loosen 4 screws F and 2 screws G (See Figure 4-8 & Figure 4-9) to remove Amp-Module Board. 1) Loosen 1 screw C (See Figure 4-5) to remove the Tuner Module.
Page 13
Dismantling Instructions & Service Positions 3139 785 31871 EN 13 Service Positions Insulation Sheet Insulation Sheet Mono Board Front Board Service Position - Front Board Service Position - Mono Board Insulation Sheet Amp Board Service Position -Amp-Board...
EN 14 3139 785 31871 Service Test Program Service Test Program To start service test program refers to Service Mode open the tray with remote control refers to Version or front panel key, while plugging xx refers to Software version number of BEA in the mains cord press 2, 5 8 on (counting up from 01 to 99) remote control, the tray will close...
Page 15
Service Test Program 3139 785 31871 EN 15 4.1.1 Reprogramming of DVD version Matrix 4.1.4 Procedure to upgrade the fi rmware After repair, the customer setting and region code may be lost. 1. Power up the set and open tray. Reprogramming will put the set back in the state in which it has left 2.
Page 16
EN 16 3139 785 31871 Service Test Program Notes:...
Revision List 3139 785 31871 EN 49 10 REVISION LIST 10.1 Manual 3139 785 31871 1. Additional of HTS3100/75 2. Additional of schematic diagram (point 2) in page 21 of document. 3. Additional of HTS3100/75 for Reprogramming of DVD version Matrix in page 15 of documents. 4.