System setup To add your LK10 keypad into your Incognito system, refer to the diagram below: SS10 Speaker cable KP10 PS10 SS10 Speaker cable KP10 Cat-5/5e cable LK10 Ribbon cable (supplied with LK10) Shift Fav-1 (Set) Menu Title Exit AH10...
Page 5
The LK10 should be placed next to the KP10, using a double J-Box and double Decora™ faceplate (not supplied). Rear view KP10 connector - Connects the LK10 to the KP10 with the supplied ribbon cable. I.C.P - In-circuit programming socket, used to upgrade keypad software when necessary. LK10 Front view...
Installation notes The LK10 is fitted on the wall by fixing it into a double USA-type J-Box (electrician’s back- box). All knock-outs in the back-box should be removed to provide maximum ventilation. Where it is desired to fit a mains lighting switch etc next to a keypad, a barrier-box or two single back-boxes must be used (bear in mind it is not preferable to fit the keypad next to a light-switch particularly if the faceplate styles will differ).
Page 7
Power requirement The LK10 runs on 24 V DC (@ 250mA max) supplied through the connecting cable from the KP10 keypad. As such there is no mains voltage present in the KP10 and the unit is often safe to fit in areas where only extra low voltage (ELV) equipment is permitted. However, it is imperative that you always check the wiring regulations in force for your application and area.
Keypad overview SHARED EDIT SLEEP LEARN Shift Fav-1 (Set) Menu Title buttons and the cloning port, please refer to the ‘Operating instructions’ and ‘Keypad setup’ sections of this guide. Buttons numbered 1-8 have dual functions, which are controlled by the Shift button. These buttons generate IR codes or macros cloned from the buttons of the same name on the LR10 learning remote (see later section on Cloning).
On-screen display SHARED Week days - The bar over a letter indicates the day of the week. Alarm - Displayed when the alarm function is set. IR - Indicates when an infra-red signal is sent from the LK10. Time - Displays current time. ‘PM’ appears when 12 hour clock is set. Date - Can be set as Month/Date or Date/Month.
Cloning from the remote control The LK10 can only be used to control source equipment once it has been cloned from the LR10. This transfers the necessary IR codes and macros into the LK10. The Incognito LR10 is a sophisticated learning remote which is able to learn the codes of all the source equipment from their own remotes.
Page 11
For the LK10 to receive commands, it must be first put into Learn mode. The LK10 has a series of menus that can be accessed by pressing and holding the Shift/Set button on the front panel. The menu options are continuously scrolled on the LK10 display until you release the Shift/Set button.
Page 12
Cloning from the remote control After approximately 7 minutes the keypad display should show ‘COMPLETE’ and return to normal operation. All data has been transferred. If the clone fails the keypad will show ‘ERROR’ or ‘TIMEOUT’. Put the transmitting LR10 remote back into Clone mode and repeat the process.
Settings menus Note: You still use your KP10 keypad to control audio functions (volume adjustment, source selection etc). To personalise other settings of the LK10, press and hold the Set button for four seconds to activate the Settings menus (Fig. 1). The LK10 screen will continuously scroll through the five menu options: Learn Alarm...
Page 14
Settings menus Alarm menu Press the Set button for five seconds and release when ‘ALARM?’ is displayed on the screen. Alarm Hour Shift Fav-1 (Set) Menu Title Exit Days When selecting ‘DAYS’, use the Monday to Friday, weekend or everyday. On/Off When the alarm is selected on, the Alarm icon Minute...
Page 15
Sleep menu This menu allows you to set the time at which the LK10 will automatically switch off. Press the Set button for five seconds and release when ‘SLEEP?’ is displayed on the screen. Sleep Hour Minute Shift Fav-1 (Set) Menu Title Exit...
Settings menus Setup menu This menu lets the user manually set the time and date of the LK10. Press the Set button for five seconds and release when ‘SETUP?’ is displayed on the screen. Setup Hour Shift Fav-1 (Set) Menu Title Exit Note: The time and date will also be set automatically after a download from the LR10.
Configure menu Press the Set button for five seconds and release when ‘CONFIG?’ is displayed on the screen. Configure 12/24 Hour Shift Fav-1 (Set) Menu Title Exit 12/24 Hour - Controls the clock display in either 12 or 24 hour format. DD/MM - Sets the order in which the date and month are displayed.
This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for accuracy at the time of printing; however, Cambridge Audio's policy is one of continuous improvement, therefore design and specifications are subject to change without prior notice.
To obtain warranty service, please contact the Cambridge Audio authorised dealer from which you purchased this product. If your dealer is not equipped to perform the repair of your Cambridge Audio product, it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent.