Advertisement
Quick Links
These instructions are for your safety. Please read through them
thoroughly before use and retain for future reference.
Parts Supplied
Ref
Description
Indoor
A
Monitor
Outdoor
B
Camera
Wall
C
mounting
bracket
Power
D
Transformer
Before You Start
• Check the pack and make sure you have all of the part listed above. If not, contact
your local store who will be able to help you.
Safety & Operating Instructions
VIDEO DOOR PHONE
NVM-704-2/NVC-3104
Illustration
Qty
1
1
1
1
Fittings Supplied
Ref
Description
Screw
E
(Dia 4x20mm)
Screw
F
(Dia 3x10mm)
H
Power cover
I
Locker
Bracket
J
Holder
Accessory
K
Connector
Illustration
Qty
8
2
1
2
1
4
Page 1
Advertisement
Related Manuals for FUTURO NVM-704-2
Summary of Contents for FUTURO NVM-704-2
- Page 1 Safety & Operating Instructions VIDEO DOOR PHONE NVM-704-2/NVC-3104 These instructions are for your safety. Please read through them thoroughly before use and retain for future reference. Parts Supplied Fittings Supplied Description Illustration Description Illustration Screw Indoor (Dia 4x20mm) Monitor Screw...
- Page 2 Technical Characteristics Specifications Indoor Unit（NVM-704-2） Dimensions 235[W] ×120 [H] ×28 [D] mm Weight 0.7Kg Input Power DC14V (External Power Supply) Power Consumption Idle mode : 2W Operating : MAX 14W Connecting System 4 wires Voice transmission Half duplex two way communication...
- Page 3 Indoor unit 1. Monitor screen 2. Talk on/Talk off (Monitor off) 3. Door open button 4. Monitor on / (Camera 1, 2 select) 5. Intercom button 6. Volume control 7. Brightness control Outdoor unit 1. Camera lens 2. White LEDs for night vision 3.
- Page 4 Safety Instructions 1. Do not install near other electronic equipment such as computers, TV, video recorder as this may cause radiated interference to the unit. 2. Do not disassemble the unit. 3. Do not spray water on the indoor unit. Do not keep the outdoor unit where it will be exposed to extreme moisture.
-
Page 5: Wiring Diagram
Assembly instructions WIRING DIAGRAM A) Cable connection 1. Connect the monitor to the camera with the cable according to the wiring diagram below. 2. Carefully insert the wires to the terminal by pressing down the terminal flap with any small tool taking care that the 2 bare wires do not touch. Page 5... - Page 6 B) Installation height 1. Recommended installation height is approximately 140cm for monitor unit and 150cm for outdoor camera. C) Installation of indoor monitor 1. Fix the wall mounting bracket in the best place by using 4 screws and plugs. 2. Carefully place the indoor monitor against the bracket and gently push down the monitor so that the pins on the bracket engage in the slots on the rear of the monitor.
- Page 7 D) Installation of outdoor camera Add the name to the nameplate 1) Release the button block from the panel and remove the cover (Fig. A & B) 2) The name plate is now accessible (Fig. C) 3) Mark your name on the plate (Fig. C) 4) Place the button block back to the panel (Fig.
- Page 8 1) Remove the front cover (Fig. E & F) 2) Mount the outdoor unit on the wall by using 2 mounting screws and wall plugs. （Adjust the camera angle if necessary.）(Fig. G) 3) Replace the front cover and security it by replacing the 2 screws at the bottom of the camera.
- Page 9 4. Activation of “Intercom” button An intercom calling can be started by any indoor monitor. When the intercom button on one indoor monitor is pressed,the intercom button color will turn on blue, this will ring all monitors in a system,you can talk with the one calling monitor by pressing the intercom button on the second monitor, Press...
- Page 10 Care and Maintenance Do not store in hot or cold areas. Extreme hot or cold temperatures can shorten the life of electronic devices and can distort/melt certain plastics or may cause malfunction. Dropping can result in failure to operate. Circuit boards can crack and may not survive the impact.
Need help?
Do you have a question about the NVM-704-2 and is the answer not in the manual?
Questions and answers