Table of Contents
Advertisement
Gas connection
GB
The cooker should be connected to the gas-supply
by a gas safe registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed "Adaptation to different gas
types". On some models the gas supply can be
connected on the left or on the right, as necessary;
to change the connection, reverse the position of the
hose holder with that of the cap and replace the
gasket (supplied with the appliance). In the case of
connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The
gas supply must be connected to the left of the
appliance. Be sure that the hose does not pass
through the rear of the cooker touching hot parts.
! make sure the supply pressure conforms with
the values shown in the table entitled
"Caracteristics of the burners and nozzles".
When the cooker is installed between cabinets
When the cooker is installed between cabinets
When the cooker is installed between cabinets
When the cooker is installed between cabinets
When the cooker is installed between cabinets
(recessed), the gas connection must be effected
(recessed), the gas connection must be effected
(recessed), the gas connection must be effected
(recessed), the gas connection must be effected
(recessed), the gas connection must be effected
by an approved flexible hose with bayonet fitting
by an approved flexible hose with bayonet fitting
by an approved flexible hose with bayonet fitting
by an approved flexible hose with bayonet fitting
by an approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for the
(BS 669 Current Edition). The gas inlet for the
(BS 669 Current Edition). The gas inlet for the
(BS 669 Current Edition). The gas inlet for the
(BS 669 Current Edition). The gas inlet for the
cookers is a threaded G 1/2 gas female fitting.
cookers is a threaded G 1/2 gas female fitting.
cookers is a threaded G 1/2 gas female fitting.
cookers is a threaded G 1/2 gas female fitting.
cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
HOT PARTS
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
! the installation must comply with gas safety
(installation and use) regulations 1984. In all cases
for the above, by low, a qualified, gas safe approved
engineer must be called for installation.
4
To make the connection, a
flexible hose should be used
corresponding to the current
gas regulations which are:
• the hose must never be at
any point in its lenght in
contact with the "hot" parts of
the cooker;
Electrial connection
Electric cookers come without a power supply cable.
The cooker is designed to operate on an electricity
supply which conforms to the electrical data shown
on the Rating Plate. The cooker can be connected to
the mains only after removing the back panel of the
cooker itself with a screwdriver.
! ! ! ! ! the following installation procedure must be carried
out by a qualified electrician. The electrical
installation must comply with the IEE Regulations,
Building & local By-Lays.
For the installation of the feeding cable carry out the
following operations:
• Using a screwdriver, prise
on the side tabs of the
terminal board cover (see fig.
A);
• Pull and open the junction
blok lid
Fig. A
! ! ! ! ! The wires in the mains lead are coloured in
accordance with the following code:
E a r t h
E a r t h
Green & Yellow
E a r t h
E a r t h
E a r t h
Blue
Neutral
Neutral
Neutral
Neutral
Neutral
L i v e
L i v e
Brown
L i v e
L i v e
L i v e
As the colours of the wires in
the mains lead may not
correspond with the coloured
L
2
markings identifying the
terminals in your plug,
N
4
proceed as follows:
Green & Yellow wire to
terminal marked "E E E E E " or
Fig. B
coloured Green or Green &
Yellow.
Brown wire to terminal marked "L L L L L " or coloured Red.
Blue wire to terminal marked "N N N N N " or coloured Black
(see fig. B).
• fix the feeding cable in the special cable stop and
close the cover.
! ! ! ! ! The power supply cable must have these minimum
requirements:
Type: H05RR-F
Section: 3x1.5 mm
2
Ensure that the mains cable is routed away from any
brackets affixed to the rear panel and is not trapped
to the rear wall when pushing the cooker into
position between cabinets.
or
Advertisement
Table of Contents
