Maytag MDE17PR Installation Instructions Manual page 21

DISPLAY
After the dryer has been installed and plugged in, the display will
show '0 minutes.'
Single Load Models
Once the unit has been plugged in and the dryer door opened and
closed, the display will show the price. In PR models set for free
cycles, the display will flash 'SELECT CYCLE' (not shown).
Single Load Models
PRICE
CONTROL SET-UP PROCEDURES
IMPORTANT: Read all instructions before operating.
The fabric setting key pads along with the digital display are used to
set-up the dryer controls. The display can contain 4 numbers and/or
letters and a decimal point. These are used to indicate the set-up
codes and related code values available for use in programming the
appliance.
P
How to use the key pads to program the controls
1. The WHITES AND COLORS key pad is used to adjust the values
associated with set-up codes. Pressing the key pad will
increment the value by one (1). Rapid adjustment is possible by
holding the key pad down.
2. The PERM. PRESS key pad will advance you through the set-up
codes. Pressing the key pad will advance you to the next
available set-up code. Holding the key pad down will
automatically advance through the set-up codes at a rate of one
(1) per second.
3. The DELICATES key pad is used to select or deselect options.
Start Operating Set-Up
Single Load PD Models: Insert service door key, turn, and lift to
I
remove service door.
Single Load PR Models: Once the debit card reader is installed
I
(according to the reader manufacturer's instructions), the set-up
mode can be entered by inserting a manual set-up card (supplied
by the reader manufacturer) into the card slot. If manual set-up
card is not available, manual set-up mode can be entered by
removing connector AA1 on the circuit board.
IMPORTANT: The console must not be opened unless power is
first removed from the dryer. To access connector AA1:
Unplug dryer or disconnect power.
Open console, disconnect plug on AA1, close console.
Plug in dryer or reconnect power.
The dryer is now in the set-up mode.
Before proceeding it is worth noting that, despite all the options
available, an owner can simply choose to uncrate a new commercial
machine, hook it up, plug it in, and have a unit which operates.
PD units are pre-set at the factory for fixed cycle price with top off.
I
PR units are pre-set for free cycle operation so they can be run
I
without readers or coins.
SET-UP CODES
The PERM.PRESS key pad will advance you from code to code.
I
The WHITE AND COLORS key pad will change the code value.
I
The DELICATES key pad will select or deselect options.
I
FOR PR MODELS: The set-up codes are the same as for the PD
models except where noted.
The set-up code is indicated by the one or two left-hand characters. The
set-up code value is indicated by the two or three right-hand characters.
CODE
6 0 6
REGULAR CYCLE PRICE
6 0 6
Represents the number of quarters (coin 1); may adjust from
0-39. (See VALUE OF COIN 1 b. 05) Advance from 0-39 by
pressing the WHITES AND COLORS key pad.
Factory preset for 6 quarters = $1.50.
PR MODELS ONLY: Factory preset for 0 quarters.
Press the PERM. PRESS key pad once to advance to next code.
7 0 5
REGULAR DRY TIME
7 0 5
Represents the number of minutes per quarter (coin 1).
Factory preset for 5 minutes per coin.
Example: 6 quarters x 5 minutes = 30 minutes.
By pressing the WHITES AND COLORS key pad, you can adjust
the value from 1–99 minutes.
Press the PERM. PRESS key pad once to advance to next code.
8 0 0
TYPE OF DRYER PRICING
8 0 0
Fixed Cycle with Top Off. For detailed description, see General
User Information.
8 F C
Fixed Cycle. For detailed description, see General User
Information.
Use DELICATES key pad to make this selection.
PR MODELS ONLY: Factory set for FC.
Press the PERM. PRESS key pad once to advance to next code.
9 0 0
CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
9 0 0
Not Selected 'OFF'.
9 0 C
Selected 'ON' and not able to be deselected. Press DELICATES
key pad 3 consecutive times to select 'ON'. Once selected 'ON'
it cannot be deselected.
Press the PERM. PRESS key pad once to advance to next code.
EXPLANATION
21