Circuit Boards Location; Schematic Diagrams - Sony TRINITRON KV-HR29M61 Service Manual

6-2. CIRCUIT BOARDS LOCATION

MG
H4
HMG
H3
C
W
SF
T (GE model)
D
UG
G1 (GE model)
BM, MS2

6-3. SCHEMATIC DIAGRAMS

Note:
• Capacitors without voltage indication are all 50V.
• All resistors are in ohms.
kΩ=1000Ω, MΩ=1000kΩ
• Indication of resistance, which dose not have one for rating electrical power, is
as follows.
Pitch : 5mm
1
Rating electrical power : / W
4
• : nonflammable resistor.
• : fusible resistor.
• : internal component.
• : panel designation and adjustment for repair.
• All variable and adjustable resistors have characteristic curve B, unless other-
wise noted.
• : earth-chassis.
• The components identified by in this basic schematic diagram have been
carefully factory-selected for each set in order to satisfy regulations regarding
X-ray radiation.
Should replacement be required, replace only with the value originally used.
• When replacing components identified by , make the necessary adjust-
ments indicated. If results do not meet the specified value, change the compo-
nent identified by and repeat the adjustment until the specified value is
achieved.
(Refer to RV8002 adjustment on Page 56.)
• Readings are taken with a PAL color-bar signal input.
• Readings are taken with a 10MΩ digital multimeter.
– 77 –
Note: The symbol display is on the component slde.
The components identified by shading and mark
are critical for safety. Replace only with part number
specified.
The symbol indicate fast operating fuse.
Replace only with fuse of same rating as maked.
H5
A
• Voltages are dc with respect to ground unless otherwise noted.
• Voltage variations may be noted due to normal production tolerances.
• All voltages are in V.
* : Measurement impossibillity.
• Circled numbers are waveform references.
• : B+ bus.
• : B– bus.
• : signal path.(RF)
Reference information
RESISTOR : RN METAL FILM
: RC SOLID
: FPRD NONFLAMMABLE CARBON
: FUSE NONFLAMMABLE FUSIBLE
: RW NONFLAMMABLE WIREWOUND
: RS NONFLAMMABLE METAL OXIDE
: RB NONFLAMMABLE CEMENT
: ADJUSTMENT RESISTOR
COIL : LF-8L MICRO INDUCTOR
CAPACITOR : TA TANTALUM
: PS STYROL
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED POLYESTER
: MPP METALIZED POLYPROPYLENE
: ALB BIPOLAR
: ALT HIGH TEMPERATURE
: ALR HIGH RIPPLE
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007
Terminal name of semiconductors in silk screen
printed circuit ( )
*
Device Printed symbol Terminal name Circuit
Collector
1
Transistor
Base Emitter
Collector
2
Transistor
Base Emitter
3 Cathode
Diode
Anode
Cathode
4
Diode
Anode (NC)
Cathode
5
Diode
Anode (NC)
Common
6
Diode
Anode Cathode
Common
7
Diode
Anode Cathode
Common
8
Diode
Anode Anode
Common
9
Diode
Anode Anode
Common
0
Diode
Cathode Cathode
Common
!¡
Diode
Cathode Cathode
Anode
Cathode
!™
Diode Anode
Anode
Anode
Cathode
Transistor Source
!£
Drain
(FET) Gate D D
G G
Source
Transistor
!¢ S S
Drain
(FET) Gate
D D
Source
Transistor
!∞
G
Drain
(FET)
Gate
S S
Emitter
!§
Transistor Collector
Base
C1 C2
C2 B1 E1
!¶
Transistor
B1
E2 B2 C1
E1 E2
C1 B2 E2
!•
Transistor
C1 C2
E1 B1 C2
B1
C1 B2 E2
!ª E1 E2
Transistor
E1 B1 C2
E1 E2
C1 B2 E2
@º
Transistor
B1
E1 B1 C2
C1 C2
C1(B2) C2
E2
B1 E1
@¡
Transistor
B1
C2 C1(B2)
E2 E2
E1(B2) E2
(B2)
B1 E1
E2
@™
Transistor B1
C1 C2
C1 C2
(B2) E1(B2) C2
E2 E1 B1
@£
Transistor B1
C2 C1
C1 C2
–
Discrete semiconductot
(Chip semiconductors that are not actually used are included.)
– 78 –
RM-1011 RM-1007 RM-1011
G
B2
B2
B2
Ver.1.5