Sharp FACSIMILE UX-108 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Telephone
  5. UX-108
  6. Service manual
Sharp FACSIMILE UX-108 Service Manual

Sharp FACSIMILE UX-108 Service Manual

Hide thumbs Also See for FACSIMILE UX-108:
Table of Contents

Advertisement

Quick Links

Download this manual
[1] Specifications ............................................ 1-1
[2] Operation panel ......................................... 1-2
[3] Transmittable documents .......................... 1-3
[4] Installation ................................................. 1-4
[5] Quick reference guide ............................... 1-7
CHAPTER 2. ADJUSTMENTS
[1] Adjustments ............................................... 2-1
[3] Troubleshooting ...................................... 2-16
[4] Error code table....................................... 2-17
[1] General description .................................. 3-1
procedures ....................................... 3-3
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SERVICE MANUAL
CONTENTS
SHARP CORPORATION
1 - 1
FACSIMILE
MODEL
Non Cutter model
UX-108
[1] Circuit description ...................................... 5-1
power supply PWB ............................ 5-11
[5] Circuit description of CIS unit ................... 5-11
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit ................................. 6-9
[3] Power supply PWB circuit ...................... 6-13
[4] Operation panel PWB circuit ................... 6-15
[1] Protocol ..................................................... 7-1
[2] Power on sequence .................................. 7-2
[1] Service tools .............................................. 8-1
[2] IC signal name .......................................... 8-3
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-108DE
No. 00ZUX108DESME
UX-108
UX-178
UX-188
UX-108
Cutter model
UX-178/188
FO-375

Advertisement

Table of Contents
loading

Related Manuals for Sharp FACSIMILE UX-108

Summary of Contents for Sharp FACSIMILE UX-108

  • Page 1: Table Of Contents

    " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used SHARP CORPORATION for after sales service only. The contents are subject to change without notice.
  • Page 2 UX-108DE CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.

  • Page 3: Chapter 1. General Description

    Length  140 to 600 mm As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

  • Page 4: Operation Panel

    UX-108DE [2] Operation panel EMPFANGSART FUNKTION AUFLÖSUNG TEL FAX LEISE LAUTSTÄRKE LAUT TEL/FAX ANRUFB STOP KURZWAHL KOPIE/HILFE WAHLWDH. WXYZ PQRS ALPHAWAHL START SYMBOLE LAUTSPR. ABRUF 10 11 9. WAHLWDH.(REDIAL key) 1. LCD-Anzeige(Display) Press this key to automatically redial the last number This displays messages and prompts during operation dialed.

  • Page 5: Transmittable Documents

    UX-108DE 5. Automatic Document Feeder Capacity [3] Transmittable documents Number of pages that can be placed into the feeder at anytime is as 1. Document Sizes follows: Normal size: max. ADF 10 sheets width 148 – 216 mm Normal size Special size: single sheet only (manual feed) length 140 –...

  • Page 6: Installation

    UX-108DE 7. Use of Document Carrier Sheet 2. Connections Connect the handset as shown and place it on the handset rest. A document carrier sheet must be used for the following documents. • ♦ The ends of the handset lead are identical, so they will go into Those with tears.
  • Page 7 UX-108DE 3. Original document support Unwrap the roll of fax paper and place it in the compartment. • Important: The roll must be placed so that the leading edge of Rotate the original document support so that it points straight out. the paper unrolls as shown.
  • Page 8 UX-108DE 4. Clearing a jammed document Remove the paper roll. If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try press- ing the START key. If it doesn’t feed out, remove it as follows: Important: Do not try to remove a document without opening the op- eration panel.

  • Page 9: Quick Reference Guide

    UX-108DE [5] Quick reference guide FUNCTION key menu The following chart shows the layout of the functions and settings accessed by pressing the FUNCTION key. First press the FUNCTION key, the appropriate numeric key as shown, and then "#" or " "...

  • Page 10: Adjustments

    UX-108DE (1) FU100 (ICP-S07) is installed in order to protect IC’s from an over- CHAPTER 2. ADJUSTMENTS current generated in the motor drive circuit. If FU100 is open, replace it with a new one. [1] Adjustments 3. Settings (1) Dial mode selector General DIAL mode (Soft Switch No.

  • Page 11: Diagnostics And Service Soft Switch

    UX-108DE [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FXA0 After 2 sec: DIAG MODE FXA0 Then press the START key.
  • Page 12 UX-108DE 3. Diagnostic items description 3. 6. Signal send mode 3. 1. Soft switch mode The mode is used to send various signals to the circuit during FAX com- munication. Every push of START key sends a signal in the following Used to change the soft switch settings.
  • Page 13 UX-108DE 4. How to make soft switch setting To enter the soft switch mode, make the following key entries in sequence. Press FUNCTION START START DATA No. 1 2 3 4 5 6 7 8 S F T SW-A1 = 0 0 0 0 0 0 0 0 Press FUNCTION key.
  • Page 14 UX-108DE 5. Soft switch description • Soft switch Initial setting Switch setting and function DATA ITEM Remarks Protect from echo Forced 4800 BPS reception Footer print Length limitation of No limit Copy/send: 60cm copy/send/receive Receive: 1.5m CSI transmission No transmitted Transmitted DIS receive acknowledgement Twice...
  • Page 15 Disconnect the line when DIS is received in RX mode Equalizer freeze control (MODEM) Equalizer freeze control 7200 BPS only CNG transmission in manual TX mode Initial compression scheme for sharp MR mode H2 mode fax in TX mode Reserved Reserved Reserved Reserved...
  • Page 16 UX-108DE Initial setting Switch setting and function DATA ITEM Remarks DTMF signal transmission level Binary input (Low) No. = 16 8 4 2 1 2 3 4 1 0 1 1 1 (0.5x10=-5dBm) Reserved Reserved Reserved DTMF signal transmission level Binary input (High) No.
  • Page 17 UX-108DE Initial setting Switch setting and function DATA ITEM Remarks Pseudo ringer sound output level to Binary input the line No. = 8 4 2 1 1 2 3 4 0 1 0 1 (-5dBm -5=-10dBm) 1 (-5 ~ -20dBm setting) Reserved Reserved Reserved...
  • Page 18 UX-108DE Initial setting Switch setting and function DATA ITEM Remarks Reserved Reserved Reserved Busy tone continuous sound detect 5 sec 10 sec time Reserved Busy tone detect continuation sound No detect Reserved Busy tone detect intermittent sound detect Busy tone detection pulse number 2pulses 4pulses 6pulses 10pulses No.
  • Page 19 UX-108DE Initial setting Switch setting and function DATA ITEM Remarks Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Sender’s phone number setting Cannot change Change allowed Reserved...
  • Page 20 UX-108DE Initial setting Switch setting and function DATA ITEM Remarks Entering DIAG mode by pressing SPEED key Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 2 –...
  • Page 21 UX-108DE • Soft switch function description SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception) SW-A1 No. 1 Protect from echo Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to Used to protect from echo in reception.
  • Page 22 When set to "0", if the other fax is Sharp model, fax transmit the docu- pulse dial mode to the tone dial mode. ment by H2 mode. When set to "1", even if the other fax is Sharp model, fax transmit the document by MR mode.
  • Page 23 UX-108DE SW-C1 No. 6 Half tone gray scale selection SW-E2 No. 1 ~ No. 4 Pseudo ringer sound output level to the line Used to determine the reading gray scale in half tone mode. Used to adjust sound volume of pseudo ringer to the line (ring back tone) generated on selecting TEL/FAX.
  • Page 24 UX-108DE SW-G3 No. 5, No. 6 Section time of quiet detection SW-J2 No. 3 Polling key The switch which sets the time from the start of detection function to the If this switch is set to 1, the last of Rapid key works as polling key. end of the function.

  • Page 25: Troubleshooting

    UX-108DE [3] Troubleshooting Refer to the following actions to troubleshoot any of problems mentioned • Apply line equalization SOFT SWITCH A5-1, 2. in 1-4. May be used in case [1] [2] [3] [4]. [1] A communication error occurs. • Slow down the transmission speed SOFT SWITCH A2-1, 2, 3, [2] Image distortion produced.

  • Page 26: Error Code Table

    UX-108DE [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) Incomplete signal frame Cannot recognize bit stream after flag NSF, DIS Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fall back Disconnects line during reception of multi page...
  • Page 27 UX-108DE M E M O 2 – 18...

  • Page 28: Chapter 3. Mechanism Blocks

    UX-108DE 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separation rubber plate ensures er- ror-free transport and separation of documents. The plate spring [1] General description presses the document to the paper feed roller to assure smooth feed- ing of the document.
  • Page 29 UX-108DE 3-5. Documents requiring use of document carrier 5. Recording block 1) Documents smaller than B6 (128mm x 182mm). 5-1. General view 2) Documents thinner than the thickness of 0.06mm. RECORDING BLOCK (NON CUTTER MODEL) 3) Documents containing creases, folds, or curls, especially those whose Scanner frame surface is curled (maximum allowable curl is 5mm).

  • Page 30: Disassembly And Assembly

    UX-108DE [2] Disassembly and assembly procedures • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
  • Page 31 UX-108DE Parts list (Fig. 2) PWB case top, bottom and PWB Part name Q’ty Part name Q’ty Mechanism unit Screw (4×6) Screw (3×6) AC cord ass’y Head earth cable Screw (3×6) Connector TEL ARG cable Screw (3×10) Power supply PWB unit PWB case unit TEL/LIU PWB unit Screw (3×10)
  • Page 32 UX-108DE Parts list (Fig. 3) Operation panel unit and scanner frame Part name Q’ty Part name Q’ty Mechanism unit Feed roller Screw (3×10) CIS cable Scanner frame unit CIS support, right Document guide lower CIS unit Reduction gear, 17/36Z CIS support, left Reduction gear, 17/21Z CIS spring Idler gear, 25Z...
  • Page 33 UX-108DE Parts list (Fig. 4) Document guide upper unit and head Part name Q’ty Part name Q’ty frame Operation panel unit Head support, right Screw (3×10) Screw (3×6) Support plate Head earth cable Document guide upper Head support, left unit Thermal head Screw (3×10) Pinch roller shaft...
  • Page 34 UX-108DE Parts list (Fig. 5) Document guide upper Part name Q’ty Part name Q’ty Rear sheet Panel lock lever CIS gear, 29Z Document sensor lever CIS roller A ass’y spring Transfer bearing Document sensor lever Separate spring Cuppling gear Separator plate CIS roller B ass’y Transfer roller Paper feed spring...
  • Page 35 UX-108DE Parts list (Fig. 6) Operation panel Part name Q’ty Part name Q’ty Operation panel unit Hopper spring Screw (2×6) Hopper guide, right Operation panel cable Hopper guide, left Operation panel PWB Stop key Start key Document tray Direct key Screw Pinion gear 12 key...
  • Page 36 UX-108DE Parts list (Fig. 7) Drive unit, PWB and cutter Part name Q’ty Part name Q’ty Mechanism unit Platen roller Screw (3×10) Platen bearing Drive unit Screw (3×10) Platen gear Speaker cable Control PWB unit Fig. 7 3 – 9...
  • Page 37 UX-108DE Parts list (Fig. 8) Speaker, paper sensor lever and paper guide upper Part name Q’ty Mechanism unit Screw Speaker Paper guide upper Hook Hook Fig. 8 3 – 10...
  • Page 38 UX-108DE Parts list (Fig. 9) Drive frame Part name Q’ty Part name Q’ty Change lever spring Planet gear lever B Planet gear, 17Z Idler gear, 25Z Change lever A Cam switch Reduction gear, 17Z Idler gear, 25Z Reduction gear, 17/36Z Screw (3×10) Planet gear, 17Z Planet gear spring...
  • Page 39 UX-108DE Parts list (Fig. 10) Wire treatment Part name Q’ty Band Screw (3×6) Screw (4×6) UL tape Core (F2064) Core (F2063) Band (100mm) Control PWB Speaker Speaker cable cable AC cord switch cable Postion of core TEL/LIU Head Power supply earth cable Binding the core with lower cabinet...
  • Page 40 UX-108DE M E M O 3 – 13...

  • Page 41: Chapter 4. Diagrams

    UX-108DE CHAPTER 4. DIAGRAMS 4 – 1...
  • Page 42 UX-108DE 4 – 2...
  • Page 43 UX-108DE 4 – 3...

  • Page 44: Chapter 5. Circuit Description

    UX-108DE 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description Transmission operation When a document is loaded in standby mode, the state of the docu- ment sensor is sensed via the 1 chip fax engine (XFC3). If the sensor 1.

  • Page 45: Circuit Description Of Control Pwb

    UX-108DE 3) 27C01012 (IC7): pin-32 DIP (ROM) [2] Circuit description of control PWB EPROM of 1Mbit equipped with software for the main CPU. 1. General description 3) W24257S-70LL (IC5): pin-28 SOP (RAM) Line memory for the main CPU system RAM area and coding/decoding Fig.
  • Page 46 UX-108DE XFC3 (IC2) Terminal descriptions Input Output Pin Description Pin Name Pin No. Type Type (Note: Active low signals have an "n" pin name ending.) CPU Control Interface − MIRQn Modem interrupt, active low. (Hysteresis In, Internal Pullup.) − SYSCLK System clock.
  • Page 47 UX-108DE XFC3 (IC2) Terminal descriptions Input Output Pin Name Pin No. Pin Description Type Type Operator Panel Interface OPI[3]/GPIO[24] (Pullup, Hysteresis In) Keyboard return [3] or GPIO[24] − LEDCTL Indicates outputs OPO[7:0] are for LEDs. − LCDCS LCD chip select. General Purpose I/O GPIO[0] (Hysteresis In) GPIO[0].
  • Page 48 UX-108DE (2) Panel control block The following controls are performed by the XFC3. • Operation panel key scanning • Operation panel LCD display (3) Mechanism/recording control block • Recording control block diagram (1) OPO[7:0]* TEST OPERATOR OPI[3:0]* BATRSTN PANEL, PANEL/LCD PWB LEDCTL* RESETN KEYPAD,...
  • Page 49 UX-108DE FEATURES (4) Modem (R96DFXL-CID) block • Group 3 facsimile transmission/reception INTRODUCTION The Rockwell R96DFXL-CID MONOFAX modem is a synchronous 9600 – ITU-TS V.29, V.27 ter, T.30, V.21 Channel 2, T.4 bits per second (bps) half-duplex modem with error detection and DTMF –...
  • Page 50 UX-108DE R96DFXL-CID (IC4) Hardware Interface Signals Pin No. Signal Name I/O Type Pin Signals – 100-Pin PQFP GP13 IA/OB Pin No. Signal Name I/O Type GP03 IA/OB GP11 IA/OB GP04 IA/OB GP05 IA/OB EN85 GP06 IA/OB 0VD2 GP07 IA/OB PORI 0VD2 XTLI 0VD2...

  • Page 51: Circuit Description Of Tel/Liu Pwb

    UX-108DE [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB TXCONT TXOUT SIGTX LINE CI DETECTOR MODEM EXT. (R96DFXL-CID) RXIN DP GEN. SIGRX RX MUTE HANDSET TEL IN TELOUT VOL A VOL B VOL C BZCONT...
  • Page 52 UX-108DE 2. Noise filter 7. Signal selection The noise filter comprises the RF choke coil, L4A, L4B. The following signals are used to control the transmission line of TEL/ FAX signal. For details, refer to the signal selector matrix table. 3.
  • Page 53 UX-108DE [Signals for status recognition according to input signals] Signal Name (CNLIUA) Signal Name (CNLIUA) RXIN Signal Name Function TELOUT TXOUT TELIN H: The handset is in the on-hook state. TELMUTE L: The handset is in the off-hook state. +24VA Incoming call (CI) detection signal.

  • Page 54: Circuit Description Of Power Supply Pwb

    UX-108DE [4] Circuit description of power supply PWB 1. Block diagram T1.25A/250V Noise Rectifying Filter AC IN Smoothing Switching Circuit Regulater Circuit Circuit Circuit (RCC system) T1.25A/250V +24V 4A/72V Photo Coupler Fig. 7 2-1. Noise filter circuit The overcurrent protection is performed by bringing Q1 to OFF state through detection of voltage increase in the auxiliary winding of T1 by The input noise filter section is composed of L and C, which reduces ZD2 and R9.

  • Page 55: Chapter 6. Circuit Schematics And Parts Layout

    UX-108DE CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT BATRST 270 x 4 VBAT C126 2200P RESET (4-4D) PWRDWN C141 15P XOUT 270 x 4 32.768kHz TSTCLK C140 22P SYSCLK +VREF (3-2A) +VREF (5-4D) SYSCLK MIRQ R105 –VREF (5-4D) (3-2A) –VREF/CLREF MIRQ R108 (5-5D)
  • Page 56 UX-108DE 6 – 2...
  • Page 57 UX-108DE XTLO XTLI +5VD2 EYEY EYEX 0VD2 EYECLKX 0VD2 SYNCIN2 0VD2 SYNCIN1 0VD2 EYESYNC 0VD2 ECLKIN1 0VD2 EYECLK 0VD2 R147 BYPASS BYBASS (1-4D) 0VD2 0VD2 0VD2 TXLOSS1 0VD1 TXLOSS2 0VD1 TXLOSS3 N.C. +5VD1 DPMUTE R157 470 CNLIUB-5 GP11 R158 470 VOLB (6-1H) GP21...
  • Page 58 UX-108DE 6 – 4...
  • Page 59 UX-108DE C164 1000P C165 1000P C163 1000P C162 1000P C176 1000P C196 82P 6 – 5...
  • Page 60 UX-108DE 6 – 6...
  • Page 61 UX-108DE Control PWB parts layout (Top side) 6 – 7...
  • Page 62 UX-108DE Control PWB parts layout (Bottom side) 6 – 8...
  • Page 63 UX-108DE 6 – 9...
  • Page 64 UX-108DE 6 – 10...
  • Page 65 UX-108DE TEL/LIU PWB parts layout (Top side) 6 – 11...
  • Page 66 UX-108DE TEL/LIU PWB parts layout (Bottom side) 6 – 12...
  • Page 67 UX-108DE RD6.2ESAB2 RD30FB3 RD3.3ESAB2 1000P 1000P 1000P 6 – 13...
  • Page 68 UX-108DE Power supply PWB parts layout 6 – 14...
  • Page 69 UX-108DE R5 100K R10 100K R9 100K R3 100K R2 100K R4 100K R11 100K R12 100K R6 100K 6 – 15...

  • Page 70: Chapter 7. Operation Flowchart

    UX-108DE CHAPTER 7. OPERATION FLOWCHART [1] Protocol Receive side Transmitter side G3 communication (Document inserted into document sensor during standby) To recording position Document inserted to the reading position (DCS) (DCS) 1st page Next page insert command Cut line printed Cut line printed Recording papor ejected Document ejected...

  • Page 71: Power On Sequence

    UX-108DE [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? “MEMORY CLEAR ?” display 3 sec ? STAND-BY START key ? COPY key ? STOP key ? “MEMORY CLEARED” display “MEMORY CLEARED” display 3 sec ? Memory clear Memory clear...

  • Page 72: Chapter 8. Others

    UX-108DE CHAPTER 8. OTHERS [1] Service tools 1. List PRICE PARTS CODE DESCRIPTION Q’TY RANK C P W B S 2 9 1 5 S C S 1 Relay board unit P S H E Z 3 3 5 4 S C Z Z Shading wave memory standard paper Relay board unit (TP2)
  • Page 73 UX-108DE 2. Description 2-1. Relay board unit 1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the relay board unit instead. • Before connecting the wiring to the relay board unit, set the test PWB switches to the fixed position.
  • Page 74 UX-108DE 3. Shading paper The white and black basis is applied to remember the shading wave- form. Be sure to perform this operation when replacing the battery or replacing the control PWB. Execute in the shading mode of DIAG mode. UX-108 SERIES SHADING WAVE MEMORY STANDARD PAPER (PSHEZ3354SCZZ) 8 –...

  • Page 75: Ic Signal Name

    UX-108DE [2] IC signal name CONTROL PWB UNIT IC9: VHiNJM2904M-2 (NJM2904M) IC5: VHiW24257S7LL (W24257S-70LLT) (TOP VIEW) (TOP VIEW) PIN NAME 1. A OUTPUT 2 .A–INPUT 3. A+INPUT 4. GND 5. B+INPUT – 6. B–INPUT Pin name Signal 7. B OUTPUT Address input A0~A12 8.
  • Page 76 UX-108DE IC8: VHiNJM2902M-1 (NJM2902) IC7: VHi27C01012TI (27C010) EP-ROM D OUTPUT A OUTPUT (TOP VIEW) Pin name Signal A-INPUT D-INPUT + – – A0~A16 Address input Chip enable A+INPUT D+INPUT Output enable Ground Program DQ1~DQ8 Data output (Program input) +5V power B+INPUT C+INPUT +12.5V power(*)
  • Page 77 UX-108DE IC4: VHiR96XFC3CID (96DFXL-CID) GP03 0VD2 GP04 CTSn GP05 0VD2 GP06 GP07 GP17 0VD2 GP16 SYNCIN2(G2XCLK) 0VD2 DCLKI(IRQ2n) +5VD1 YCLK XCLK XTLO XTLI PORin 0VD2 0VD2 EN85n RTSn GP11 RAMPIN SEE NOTE 1 GP13 +5VD2 0VD1 SWGAINI ECLKIN1 SYNCIN1 READn WRITEn IRQn 8 –...
  • Page 78 UX-108DE IC2: VHiR96XFC3CID (XFC3) VSSO GPIO20/ALTTONE SM0/GPO4 SM1/GPO5 SM2/GPO6 SM3/GPO7 VSSO VDDI START CLK1 CLK1N CLK2 FCS2N/VIDCTL1 FCS1N/VIDCTL0 VDDO VSSI GPIO0 GPIO1/SASTXD GPIO2/SASRXD GPIO3/SASCLK GPIO4 VHIR96XFC3CID GPIO5/SSCLK2 VSSO VSSO GPIO6/SSTXD2 GPIO7/SSRXD2 GPIO8/FWRN GPIO9/FRDN GPIO10/SSSTAT2 GPIO11/BE /SERINP VDDO VSSI PCLK GPIO12/CS2N POAT GPIO13/CS3N GPIO14/CS4N...

  • Page 79: Parts Guide

    UX-108DE PARTS GUIDE UX-108 MODEL CONTENTS Control PWB unit Cabinet, etc. TEL-Liu PWB unit Upper cabinet Power supply PWB unit Document guide upper Hardware parts Drive unit Index Packing material & Accessories Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specifi to the product specification.
  • Page 80 UX-108DE [1] Cabinet, etc. DOCUMENT GUIDE UPPER DRIVE UNIT – 1 –...
  • Page 81 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [1] Cabinet etc. LFRM-2184XHZZ Head frame MSPRC2949FFZZ Head spring A MSPRC2950FFZZ Pinch roller pressing spring NROLP2334XHZA Pinch roller NSFTZ2281FFZZ Pinch roller shaft PGIDP2497XHZZ Head support,left PGIDP2498XHZZ Head support,right PSHEZ3324FFZZ Head sheet QCNW-4748XHZZ Head cable QCNW-4754XHZZ...
  • Page 82 UX-108DE [2] Upper cabinet [3] Document guide upper – 3 –...
  • Page 83 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [2] Upper cabinet GCABA2297XHZD Upper cabinet JBTN-2216XHZA 12 key JBTN-2217XHZA Direct key JBTN-2218XHZZ Start key JBTN-2219XHZZ Stop key LPLTP2909XHZA Document tray MSPRC2954XHZZ Hopper spring NGERP2318XHZZ Pinion gear PGIDP2501XHZA Hopper guide,left PGIDP2502XHZA Hopper guide,right QCNW-4816XHZZ Panel cable...
  • Page 84 UX-108DE [4] Drive unit [5] Packing material & Accessories TAPE CORD PAPER – 5 –...
  • Page 85 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [4] Drive unit LFRM-2187XHZZ Drive unit frame LPLTM2910XHZZ Motor heat sink MCAMP2024XHZZ MLEVP2266XHZZ Planet gear lever A MLEVP2267XHZZ Planet gear lever B MLEVP2268XHZZ Change lever A MSPRC2955XHZZ Planet gear spring MSPRT2956XHZZ Change lever spring NGERH2379XHZZ Idler gear 25Z...
  • Page 86 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit UBATZ6441CCMM Battery(CR2032) [BAT1] VCEAGA1HW105M Capacitor(50WV 1µF) [C1] VCEAGA1HW475M Capacitor(50WV 4.7µF) [C2] VCEAGA1EW476M Capacitor(25WV 47µF) [C3] VCEAGA1HW475M Capacitor(50WV 4.7µF) [C4] VCEAGA1HW106M Capacitor(50WV 10µF) [C5] VCEAGA1HW106M Capacitor(50WV 10µF) [C6] VCEAGA1EW476M Capacitor(25WV 47µF) [C7]...
  • Page 87 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit VCKYTV1HB222K Capacitor(50WV 2200PF) [C172] VCKYTV1HB102K Capacitor(50WV 1000PF) [C173] VCKYTV1HB102K Capacitor(50WV 1000PF) [C176] VCKYTV1HB102K Capacitor(50WV 1000PF) [C177] VCKYTV1EF104Z Capacitor(25WV 0.1µF) [C178] VCKYTV1HB102K Capacitor(50WV 1000PF) [C179] VCKYTV1HB102K Capacitor(50WV 1000PF) [C180] VCCCTV1HH220J Capacitor(50WV 22PF)
  • Page 88 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R107] Resistor(1/10W 10KΩ ±5%) VRS-TS2AD103J [R108] Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R109] Resistor(1/10W 270Ω ±5%) VRS-TS2AD271J [R110] Resistor(1/10W 3KΩ ±5%) VRS-TS2AD302J [R111] Resistor(1/10W 150KΩ ±5%) VRS-TS2AD154J [R112] Resistor(1/10W 47.5KΩ...
  • Page 89 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Control PWB unit Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R198] Resistor(1/10W 3KΩ ±5%) VRS-TS2AD302J [R199] Resistor(1/10W 118KΩ ±1%) VRSTS2AD1183F [R200] Resistor(1/10W 8.2KΩ ±5%) VRS-TS2AD822J [R201] Resistor(1/10W 10KΩ ±5%) VRS-TS2AD103J [R202] Resistor(1/10W 3.3KΩ ±5%) VRS-TS2AD332J [R203] Resistor(1/10W 5.1KΩ...
  • Page 90 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] TEL/Liu PWB unit VCEAGA1HW225M Capacitor(50WV 2.2µF) [C6] VCEAGA1EW476M Capacitor(25WV 47µF) [C7] VCEAGA1HW226M Capacitor(50WV 22µF) [C8] VCEAGA1HW225M Capacitor(50WV 2.2µF) [C9] VCEAGA1HW106M Capacitor(50WV 10µF) [C10] VCEAGA1HW475M Capacitor(50WV 4.7µF) [C11] VCKYTQ1HB393K Capacitor(50WV 0.039µF) [C101] VCKYTQ1HB223K Capacitor(50WV 0.022µF)
  • Page 91 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] TEL/Liu PWB unit Resistor(1/10W 300Ω ±5%) VRS-TS2AD301J [R114] Resistor(1/10W 20KΩ ±5%) VRS-TS2AD203J [R115] Resistor(1/10W 22KΩ ±5%) VRS-TS2AD223J [R116] Resistor(1/10W 910Ω ±5%) VRS-TS2AD911J [R117] Resistor(1/10W 820Ω ±5%) VRS-TS2AD821J [R118] Resistor(1/10W 56KΩ ±5%) VRS-TS2AD563J [R119] Resistor(1/10W 22KΩ...
  • Page 92 UX-108DE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [8] Power supply PWB unit 0CBUKZ0826ZZ/ Filter(ELF15N003A) [L1] 0CBUDC0163BB/ Photo coupler(PC123FY8) [PC1] 0CBUAG0161CZ/ FET(FS5KM-18A) [Q1] 0CBUAC0027CZ/ Transistor(2SC2655-Y) [Q2] 0CBUAC0034EZ/ Transistor(2SC1740S) [Q3] 0CBUAC0264AZ/ Transistor(2SC1741ASQR) [Q4] 0CBUEEB564CS/ Resistor(RD16S564J) [R1] 0CBUEFER33CH/ Resistor(SPRX2-R33J) [R2] 0CBUEEB153CS/ Resistor(RD16S153J) [R3] 0CBUEEB101CS/...
  • Page 93 UX-108DE I n d e x PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK NSFTZ2273XHZZ 1-34 SPAKA162AFFZR 5-11 CCNW-4745FF01 1-17 NSFTZ2281FFZZ SPAKA231AFFZZ CPWBX2945FF51 1-43 SPAKC232AFFZZ ″ 6-901 PCUSK2113FFZZ 5-13 SPAKP3385FFZZ...
  • Page 94 UX-108DE PRICE PRICE PRICE PART PART PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK VCKYTV1CF105Z 6-77 VCKYTV1HB473K 7-23 VRS-TS2AD103J 6-197 ″ ″ ″ 6-80 7-25 6-201 ″ ″ 7-32 VCKYTV1HB681K 6-79 6-213 ″...
  • Page 95 UX-108DE PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK VRS-TS2AD271J 6-255 VS2SC2412KR-1 7-73 ″ 6-256 VS2SC2412KS-1 6-150 ″ 6-257 VS2SD1858Q2-1 6-149 ″ 6-258 ″ 6-269 XBBSD30P06000 50-B1 ″...
  • Page 96 RANK MARK RANK © COPYRIGHT 1998 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents