Advertisement
2. INTRODUCTION
Manufactured from lightweight aluminium with a pressed steel body. Gives superior strength to safely support vehicle for extended period of time.
Supplied with captive, multi-position load support pin. Ideal for the racing/kit car enthusiast.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AS1500S
Capacity Each: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 tonnes (1,500 kg)
Capacity Pair: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 tonnes (3,000 kg)
Minimum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mm
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395mm
4
OPERATION
4.1.
Refer to vehicle handbook for correct jacking procedure. Check to ensure manufacturer's recommended jacking points are in good
condition.
4.2.
Position stands beneath the manufacturer's recommended support points.
4.3.
To adjust stands, lift column up to jacking point, lower until a pin hole is visible, push pin all the way through.
4.4.
Carefully and slowly lower vehicle onto stands. Ensure load bearing points sit in the centre of the crutches and that the stands are stable.
Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
▲
DANGER! You must follow instructions carefully and ensure you DO NOT load the stands off centre. Failure to heed these warnings may
cause damage, injury or loss of life.
5. MAINTENANCE
5.1.
Before each use, check that stands and stand welds are not cracked and that there are no missing or damaged parts.
Any suspect axle stands must be removed from service immediately.
5.2.
Due to the potential hazards associated with stands, do not misuse, or make any modification, to the stands or components.
5.3.
It is the responsibility of the owner to ensure that the operator has read these instructions together with the safety features on the
side of the stand and that the operator is familiar with the stand's use and limitations.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal of it according to local regulation
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
s.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
AS1500S Issue: 5(I)- 27/09/16
Advertisement
