Related Manuals for Syncronorm SyncroSwitch
Summary of Contents for Syncronorm SyncroSwitch
- Page 1 SyncroSwitch Operating Manual www.syncronorm.com #liquidinspiration info@syncronorm.com...
- Page 2 & hardware solutions fitting to your dedicated project. From show-design, training-programs, instant support & consulting to continuously soft- & hardware development, the team at Syncronorm is eager to realize your visions. Syncronorm provide the most established & renowned products for the entertainment- &...
- Page 3 The SyncroSwitch unit features six independently controllable outputs which can output 16amps @230V AC (resistive load). This makes the SyncroSwitch a suitable tool for all your switching needs: High Power, Low Power, Audio or Lighting Signal, Motor Control, Valves or Power of VFD´s.
- Page 4 Preface This document is a guideline for controlling the hardware of Syncronorm‘s fountain control systems. The information contained in this manual will give you a sufficient understanding of this product, helping you to use the unit correctly and effectively. Adhere to all instructions contained in this manual, when installing and operating this unit.
-
Page 5: Safety Instructions
Intended Use The SyncroSwitch, in the following referred to as „unit“, may only be used as specified as follows: The DMX-RDM High Power Contact Relay Module 6x is an intelligent DMX demultiplexer, which decodes digital data complying with standards USITT DMX512 and DIN 56930-2. The card drive changes over six contact relay outputs. -
Page 6: Save Operation
Syncronorm GmbH or personnel with suitable training. Dangers resulting from non-adherence to the Safety Information Please note that Syncronorm GmbH assumes no liability for damage, downtimes or malfunctions resul- ting from non-adherence to this installation and operating manual. By ignoring or not adhering to all of the safety information contained in this manual, you could endanger people, the environment and the system of this unit. - Page 7 Syncronorm GmbH have neither been tested nor approved by Syncronorm GmbH. For this reason, the installation and/or use of such products can, under certain circumstances, negatively affect the specifications for the device. This could also lead to restrictions of the active and/or passive safety of the device.
- Page 8 CONNECTION The decoder SyncroSwitch consists of the following input and output connectors: CN13 POWER SUPPLY 230V AC grey L, 230V AC blue N, 230V AC CN8 Switching output 1 (3-pin spring terminal, light grey, grey, dark grey) 1 light grey COMMON...
- Page 9 Error blinking at data errors or loss of communication. Wiring To put the DMX relay interface SyncroSwitch to work, it must be wired properly. We strongly recommend to use fused line and load connections. Output connectors: CN8 CN7 CN6 CN5 CN4 CN3...
- Page 10 CONNECTION Start Address Switches The DMX relay decoder SyncroSwitch has been preset to DMX start address 001. If another start address is required, it must be set using a start address board 3000P or 3003P . This start address board is optionally available.
- Page 11 (OMRON, Type G2R-1-ASI, available at DMX/RDM The SyncroSwitch 6x RDM is compatible with ANSI E1-20 DMX RDM Version 1.0. Please note some special properties of devices complying with DMX RDM: DMX HOLD properties are not supported by RDM standard ANSI E1-20. A factory specific command (DMX HOLD) has been added to compensate these restraints.
-
Page 12: Maintenance And Cleaning
• Connect the equipment to an outlet other than the receiver ‘s • Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any change or modification to the product not expressly approved by SLH could void the user’s authority to operate the device. (C) 2020 Syncronorm GmbH... - Page 13 If services by Syncronorm GmbH are provided under the terms of this guarantee, this does not lead to extension or renewal of the guarantee period. Your legal rights as a purchaser, especially those ensuing from the warranty, persist.
Need help?
Do you have a question about the SyncroSwitch and is the answer not in the manual?
Questions and answers