If you don’t have IAS installed on your camera and would like to learn more about it, call 1-800-GO EPSON, or visit our website at http//www.epson.com. CPD 8424R1...
EPSON is a registered trademark of SEIKO EPSON Corporation. PhotoPC is a registered trademark, and HyPict, Image Authentication System, and FaxAdvice are trademarks of Epson America, Inc. SoundAdvice is a service mark of Epson America, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
System Requirements Your system must have the following: ® compatible PC with a 486 or higher processor ® Microsoft Windows ® Windows NT 9-pin serial port or USB port (Windows 98 only) At least 16MB RAM VGA monitor with minimum resolution of 480 and at least 16-color display Installation and Setup This section explains how to install the IAS software on...
Installing IAS Follow these steps to install IAS: 1. Insert the EPSON Image Authentication System CD into your CD-ROM drive. 2. Double-click the My Computer icon on your Windows desktop: 3. Double-click the CD-ROM drive icon: 4. Double click the Setup.exe icon: 5.
Uploading IAS to Your Camera EPSON Image Authentication System verifies the authenticity of pictures taken only after the IAS program is uploaded to your camera. You can use this procedure both to upload IAS to your camera and to verify that IAS is loaded on a camera.
Turn off the camera and LCD screen, then follow these steps: 1. Locate your computer’s serial or USB port. Note: If you are connecting the camera to a serial interface and your computer has two ports, connect your camera to COM1. 2.
If you are using the USB cable, plug the connector into the USB port on your computer or into a port on a USB hub. Note: Although you can use a USB hub, it’s best to connect the camera directly to the computer’s USB port.
3. Open the connector cover on the side of the camera. Align the serial or USB cable with the port and plug it in. USB/serial interface serial port...
If you’re using batteries instead of an AC adapter, make sure your batteries are fully charged. 5. Click Start , point to Programs , EPSON Image Authentication System , and click Camera Uploader . You see this message: Your software license permits you to upload the software to one camera only.
6. Click OK . You see the IAS uploader screen: 7. Click the UPLOAD button. When the software has been uploaded to your camera, you see the following screen:...
Note: If IAS can’t find your camera, follow the instructions on the screen to establish a connection. If you purchased additional copies of software, continue with step 8. Otherwise, go to step 9. 8. To upload IAS to another camera, disconnect the first camera and connect the second.
To verify a picture: 1. Transfer the photos to your computer as described in your camera manual. 2. Click Start , point to Programs , EPSON Image Authentication System , and click EPSON IAS Verification . You see the following screen:...
3. From the File menu, select Open , or click the Open Folder button. You see the Open dialog box. Note: The command Select Key List File on the File menu is not operational for this release. 4. Locate and select the image files you want to verify. To select more than one file, hold down the Ctrl key while you click on the files.
The File List View lists the selected files and the following details for each picture: Verification Results PASS indicates the picture has not been altered. FAIL means the picture has been altered. Non-IAS image indicates the picture was taken with a camera without IAS loaded. ERROR indicates an error condition.
Displaying Different Views In addition to the File List View, you can display verification results for a single image file (Test Info View), or you can display the File List View and Test Info View at the same time. File List View Test Info View button button...
To display the Test Info View, click the Test Info View button in the toolbar, or choose Test Info View from the View menu. You see the following screen: In addition to verification results, the Test Info View displays a thumbnail image of the selected picture.
To see the File List View and Test Info View at the same time, click the Both Views button, or choose Both Views from the View menu. You see the following screen: To return to the File List View, click the File List View button on the toolbar, or choose File List View from the View menu.
EPSON provides technical assistance through electronic support services and automated telephone systems 24 hours a day, seven days a week, as follows: From the Internet, you can reach EPSON’s Home Page at http://www.epson.com. For pre-recorded answers to commonly asked questions, call EPSON SoundAdvice (800) 922-8911.
Camera Frame Rates When you’ve uploaded IAS to your camera, it takes slightly longer to process pictures. The tables below give the camera frame rates (approximate time, in seconds, you must wait between pictures) when IAS is installed. Color Mode, LCD Off Image PhotoPC Quality...