Samsung 680 Series Quick Setup Manual

Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
50 inches model only
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the PDP TV.
x
Stand the product up fasten the screws. If you fasten the screws with the
with the PDP TV placed down, it may lean to one side.
Screws (M4 X L10)
1
Connect the Guide Stand to the
Stand using four screws (M4 X L10)
as shown.
2
With your TV upright, connect the
TV to the Stand.
Rear
Step 2
: Install the Batteries into the Remote
To install batteries into your remote
control, follow these steps:
1. Lift the cover on the back of the
remote upward as shown in the figure
to the right.
2. Install two AAA batteries.
✎
Make sure to match the + and - ends of the batteries to the diagram in
the battery compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
All manuals and user guides at all-guides.com
Guide Stand
Stand
Rear
3
Fasten two screws (M4 X L12) at
position 1, and then fasten the
two screws (M4 X L12) at position
2.
2
1
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box
Use one of the connections below to connect your TV to an external A/V device. We re
Audio Cable
(Not Supplied)
Very Good Connection
HD connection (up to 1080p)
Using an HDMI to DVI Cable
Device
Good Connection
Component connection (up to 1080p)
Using an Audio/Video Cable
DVD / Blu-ray player / HD Cable Box / HD
Satellite receiver (STB)
Top view
Blu-ray player
Front
Rear
Component Cable
(Not Supplied)
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control,
select the language for the On
Screen Display (OSD), and then
press the ENTERE button.
2
Select Home Use, and then
press the ENTERE button. If you select Store Demo, the TV will reset your
picture and audio settings every 30 minutes.
3
Select Antenna Source and Channel Source. If Antenna Source is
Cable or Auto, you must select Channel Source to same type as your
cable system type. After selecting source, select Search; then press the
ENTERE button on your remote.
✎
Most cable systems are Standard(STD) systems, If you are not sure
about what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5.
After Plug & Play is complete, set your TV to Channel 3 or 4, according
to the directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
5
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTERE button.
HDMI to DVI Cable
(Not Supplied)
AUDIO OUT DVI OUT
COMPONENT OUT AUDIO OUT
MENU button. To turn on your TV, press the
Select Language of the OSD.
Menu Language
Audio Cable
(Not Supplied)
POWER
Plug & Play
English
Español
:
Français
U Move E Enter