Advertisement
All manuals and user guides at all-guides.com
graphic data recorded. Press S2
button to cycle the selection
backward.
4. When displaying maximum
absolute pressure, minimum
absolute pressure and the individual
statistic and graphic data recorded,
the corresponding log time and date
will be swapping in every 2 seconds.
5. Press S3/S4 button to return to
BAROMETER mode.
TO USE THE CHRONOGRAPH
1. Press S3 button to select
CHRONOGRAPH mode.
2. The chronograph will then be
displayed in its current sate – reset,
running or stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reset the
chronograph to zero first.
Press S2 button to stop counting,
then press and hold S2 button for
around 3 seconds to reset the
counter to zero.
FOR THE MEASUREMENT OF
ELAPSED TIME
In CHRONOGRAPH mode,
1. Press S1 button to start counting.
2. To stop counting, press S2 button.
Press S1 button to resume from
where if left off.
3. To reset to zero, press S2 button to
stop counting, then press and hold
S2 button for around 3 seconds to
reset the counter to zero.
FOR THE MEASUREMENT OF
SPLIT TIME AND LAP TIME
In CHRONOGRAPH mode,
1. Press S1 button to start counting.
2. While the chronograph is running,
press S1 button once to register a
lap. Both the split time and lap time
will be displayed.
After 3 seconds, the currently
accumulated split time and lap time
will be displayed.
3. Repeat the last step until all the
laps have been registered.
4. To stop counting, press S2 button.
Press S1 button to resume from
where if left off.
5. To reset to zero, press S2 button to
stop counting, then press and hold
S2 button for around 3 seconds to
reset the counter to zero.
NOTE: The watch can record up to a
maximum of 99 laps. During a
measurement of split time and lap
time, the message "FULL" will be
displayed when the memory is full.
TO USE THE RECALL FUNCTION
1. After the measurement of split
time, press S4 button to select
RECALL mode when the
chronograph is stopped.
2. After 2 seconds or by pressing
S1/S2 button, the sum of time of all
lap counting (TOTAL) will be
displayed.
3. Press S1/S2 button to select
displaying the sum of time of all lap
counting (TOTAL), best lap (BEST),
average time (AVERAGE) or
individual lap record (LAP-XX).
4. Press S4 button to return to
CHRONOGRAPH mode or press S3
button to return to TIME mode.
NOTE: The lap record(s) will be cleared
when chronograph is reset.
NOTE: The average time (AVERAGE)
is the total time of all lap counting
over the number of lap count.
TO SET THE TIMER
1. Press S3 button to select TIMER
mode.
2. Press and hold S4 button for around
3 seconds, the second digits will
blink.
3. Press S1/S2 button to set the
second digits. Holding down the
button will speed up the process.
4. Press S3 button, the minute digits
will blink.
5. Press S1/S2 button to set the
minute digits.
6. Press S3 button, the hour digits will
blink.
7. Press S1/S2 button to set the hour
digits.
8. Press S3 button, the mode selection
will blink.
9. Press S1/S2 to select among
countdown stop mode (Cd-STOP),
countdown up mode (Cd-UP) and
countdown repeat mode (REP-00).
10.After finish making all the settings,
press S4 button to confirm.
TO USE THE TIMER
In countdown stop mode (Cd-STOP),
1. Press S1 button to start counting.
The timer icon
will appear.
2. To stop counting, press S2 button.
Press S1 button to resume from
where it left off.
3. To reload the timer, press S2 button
to stop counting, and then press S2
button again to reload the timer to
the preset value.
4. After reaching zero in a countdown,
a beep sound will be emitted and
the timer icon
will blink for 10
seconds. The timer will then be
reloaded to the preset value.
In countdown up mode (Cd-UP),
1. Press S1 button to start counting.
The timer icon
will appear.
2. To stop counting, press S2 button.
Press S1 button to resume from
where it left off.
3. After reaching zero in a countdown,
a beep sound will be emitted and
the time icon
will blink for 10
seconds. The timer will
start counting up simultaneously.
4. Press S2 button once to stop
counting. Press S2 button again to
reload the timer to the preset value.
In countdown repeat mode (REP-00),
for time value < 1 minute:
1. Press S1 button to start counting.
2. To stop counting, press S2 button.
Press S1 button to resume from
where it left off.
3. After reaching zero in a countdown,
a beep sound will be emitted for 1
second. The timer will repeat
counting at the preset value
simultaneously.
4. Press S2 button once to stop
counting. Press S2 button again to
reload the timer to the preset value.
for time value > 1 minute:
1. Press S1 button to start counting.
2. To stop counting, press S2 button.
Press S1 button to resume from
where it left off.
3. After reaching zero in a countdown,
a beep sound will be emitted and
the timer icon
will blink for 10
seconds. The timer will repeat
counting at the preset value
simultaneously.
4. Press S2 button once to stop
counting. Press S2 button again to
reload the timer to the preset value.
NOTE: In countdown repeat mode, the
maximum number of repetition is 100
(REP-00 to REP-99).
NOTE: When timer beep sound is
emitted, press any button to disable
the beep sound.
TO SELECT AND SET ON/OFF
THE ALARM
1. Press S3 button to select ALARM
mode.
2. Press S2 button to select from
ALARM 1 (AL-1) to ALARM 5 (AL-
5). Each alarm can be set as
different modes - time alarm,
altitude alarm or pressure alarm.
3. Press S1 button to toggle between
on and off of the alarm. If the alarm
is on, the alarm icon
will appear.
TO SELECT THE ALARM MODE
OF INDIVIDUAL ALARM
1. In individual alarm (AL-1 to AL-5),
press and hold S4 button for around
3 seconds. The message "Time-AL"
will be displayed.
2. Press S1/S2 button to select time
alarm setting mode (Time-AL),
altitude alarm setting mode (ALTI-
Advertisement
