Ordering Spare Parts - Stihl MS 201 C-M Instruction Manual

30 Ordering Spare Parts

MS 201 C-EM with ErgoStart:
29.6 Cutting Attachment
Actual cutting length may be less than the speci‐
fied length
29.6.1 Rollomatic guide bars
Bar lengths (3/8" P pitch):
Groove width:
29.6.2 Carving guide bars
Bar lengths (1/4" pitch):
Groove width:
29.6.3 3/8" Picco chains
Picco Micro 3 (63 PM3) Type 3636
Pitch:
Drive link gauge:
Picco Super (63 PS) Type 3617
Pitch:
Drive link gauge:
Picco Super 3 (63 PS3) Type 3616
Pitch:
Drive link gauge:
Picco Duro 3 (63 PD3) Type 3612
Pitch:
Drive link gauge:
Picco Micro (63 PM) Type 3613
Pitch:
Drive link gauge:
29.6.4 1/4" chains
Rapid Micro Spezial (13 RMS) Type 3661
Pitch:
Drive link gauge:
29.6.5 Chain Sprockets
6-tooth for 3/8" P (spur sprocket)
Max. chain speed according to
ISO 11681:
Chain speed at maximum power: 18.6 m/s
8-tooth for 1/4" (spur sprocket)
Max. chain speed according to
ISO 11681:
Chain speed at maximum power: 16.9 m/s
29.7 Noise and Vibration Data
For further details on compliance with Vibration
Directive 2002/44/EC visit www.stihl.com/vib.
29.7.1 Sound pressure level L
99 dB(A)
29.7.2 Sound power level L
112 dB(A)
0458-598-0121-C
4.1 kg
30, 35, 40 cm
1.3 mm
30 cm
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
1/4" (6.36 mm)
1.3 mm
26.0 m/s
23.6 m/s
to ISO 22868
p
to ISO 22868
w
29.7.3 Vibration measurement a
ISO 22867
MS 201 C-M with
3/8" P chain:
MS 201 C-EM with
3/8" P chain:
The K‑factor in accordance with Directive
2006/42/EC is 2.0 dB(A) for the sound pressure
level and sound power level; the K‑factor in
accordance with Directive 2006/42/EC is
2
2.0 m/s for the vibration level.
29.8 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation (EC) No. 1907/2006 see
www.stihl.com/reach.
29.9 Exhaust Emissions
The CO value measured in the EU type approval
2
procedure is specified at www.stihl.com/co2.
The measured CO value was determined on a
2
representative engine in accordance with a
standardized test procedure under laboratory
conditions and does not represent either an
explicit or implied guarantee of the performance
of a specific engine.
The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.
30 Ordering Spare Parts
Please enter your saw model, serial number as
well as the part numbers of the guide bar and
saw chain in the spaces provided. This will make
re-ordering simpler.
The guide bar and saw chain are subject to nor‐
mal wear and tear. When purchasing these
parts, always quote the saw model, the part
numbers and names of the parts.
Model
Serial number
Guide bar part number
English
to
hv,eq
Handle, left Handle,
right
2 2
3.3 m/s 3.3 m/s
2 2
3.3 m/s 3.3 m/s
37