Advertisement
Quick Links
BF-IDU01
RFID-Reader
Company Addresses
Europe, Germany, Headquarter
Balluff GmbH
Schurwaldstraße 9
D-73765 Neuhausen, Germany
Argentina
Balluff Argentina S.R.L.
Echeverría 1050, 1st UF 2
1604 Buenos Aires - Florida Oeste
Australia
Balluff Pty Ltd.
18 Malvern Street
Bayswater, 3153 Victoria
Brasil
Balluff Controles Elétricos Ltda.
Rua Francisco Foga, 25 ,Distrito Industrial
CEP 13280.000 – Vinhedo – SP
Canada
Balluff Canada Inc.
2840 Argentia Road, Unit 2 Mississauga,
Ontario L5N 8G4
China
Balluff (Shanghai) Trading Co. Ltd.
No.800 Chengshan Rd, 8F, Building A, Yunding International Commercial Plaza
200125, Pudong, Shanghai
Japan
Balluff Co., Ltd.
Aqua Hakusan Bldg. 9F 1-13-7 Hakusan, Bunkyo-ku,
Tokyo 113-0001
Mexico
Balluff de México S.A. de C.V.
Anillo Vial II Fray Junipero Serra No. 4416; Colonia La Vista Residencial
CP 76232 Delegación Epigmenio González, Querétaro
USA
Balluff Inc.
8125 Holton Drive, Florence
Kentucky 41042-0937
BF-IDU01
RFID-Reader
Operating Guide
Purpose of the Device
The BF-IDU01 device is intended to read and write "EPC Global Class 1 Gen2" compliant data
carriers (so called tags) via country dependent UHF radio frequencies.
Check that you have the right device variant
This UHF system consists of a radio frequency unit and an integrated antenna according to
specifications and may only be operated within the specified countries subject to all applicable
national legal regulations and standards.
Check that the type label contains the correct type approval symbol for your country.
► When using the UHF system in the European Community, the provisions in ETSI standard 302 208
apply.
► When using the UHF system in the USA, the directives of the FCC, Part 15 B and 15 C, apply.
► When using the UHF system in Canada, the directives of the IC, RSS-210 apply.
► When using the UHF system in Mexico, the directives of the SCT, NOM-121-SCT1-2009 apply.
► When using the UHF system in Argentina, the directives of Resolución SC 729/80 and SC 784/87
apply.
► When using the UHF system in Brazil, the directives of the ANATEL, 506/2008 and 442/2006 apply.
► When using the UHF system in China, the directives of the RFID National Standard and GB 9254
apply.
► When using the UHF system in Japan, the directives of "Radio Law" and ARIB T106 apply.
► When using the UHF system in Australia, the directives of the Radiocommunications Class License
2000 (Item 32A) apply.
Advertisement
Related Manuals for Balluff BF-IDU01
Summary of Contents for Balluff BF-IDU01
- Page 1 Ontario L5N 8G4 Purpose of the Device China The BF-IDU01 device is intended to read and write "EPC Global Class 1 Gen2" compliant data Balluff (Shanghai) Trading Co. Ltd. No.800 Chengshan Rd, 8F, Building A, Yunding International Commercial Plaza carriers (so called tags) via country dependent UHF radio frequencies.
- Page 2 Connecting the Device Setup and Operation The device has to be connected to one of the head connectors "H1" .. "H4" of a Balluff BIS V The BF-IDU01 device will operate when the BIS V control unit receives read or write commands control unit via standard 4-wire cable with M12 industry connectors.
- Page 3 Class B: (Section 15.105) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ...
- Page 4 Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d'une personne).