Table of Contents
Advertisement
RN42277MUK Rev10_Instruction Booklet 23/04/2013 13:47 Page 4
LOCATION
Locate the steam generator
horizontally on the iron rest
plate of your ironing board (if
large enough) or on a heat
resistant stand at the same
height as your ironing board
or below it. Always ensure
the generator is on a firm
surface when ironing.
WARNING: Do not use the
product on a surface which
could be damaged by heat
or steam such as a
worktop or a polished
wood surface.
If in doubt, contact Morphy
Richards.
BEFORE USE
Remove any protective
sticker from the soleplate and
the base unit, if any.
Unwind and straighten the
power cord · and supply
cord fi.
Slide out the water tank ‡
and fill (see filling
instructions).
When ironing with the iron
temperature set at 2-dot
setting, the steam output
should be set at the lower
end of the steam range.
Textiles and clothes are
supposed to carry ironing
instructions. If they don't, you
should follow the
Temperature guide on page
3, but be sure to test the
temperature by ironing the
hem of the garment or similar
discreet area first.
If you turn the control dial
down from a hot setting to a
cooler setting, wait until the
iron temperature has
stabilised before you
continue ironing.
FILLING
1
Place the steam generator on
a stable ironing board or
table, with the iron resting on
its stand.
UK Helpline 0844 871 0960
4
2
Release the detachable water
tank by sliding outwards A.
A
3
Remove the anti-scale filter
by pulling upwards B.
B
4
Fill the tank to the 'fill to here'
line with clean tap water C.
C
IN HARD WATER AREAS,
THE USE OF DISTILLED OR
DEMINERALISED WATER
IS RECOMMENDED.
Never use battery topping
up fluid or water containing
any substances like starch,
sugar, fragrant additives or
defrosted water from a
refrigerator.
5
Re-install the anti-scale filter
and re-position the water
tank on the base unit and
push securely into place.
Please make sure the tank is
secure D.
D
6
Always pour out any
remaining water after use
(see 'Emptying and storing',
page 6).
Replacement Parts 0844 873 0726
Re-filling 'in use'
1
When the water level
becomes low, the pump
begins to emit a clicking
noise. This is due to air being
pumped instead of water and
is quite normal.
Refilling can be done whilst
the appliance is in operation.
It is not necessary to wait for
the appliance to cool down.
2
Slide out the water tank and
fill (see filling instructions).
STEAM IRONING
1
Unwind and straighten the
power cord · and supply
cord fi.
2
Slide out the water tank and
fill (see filling instructions).
3
Connect the appliance to a
suitable mains outlet, and
switch on the socket. All 5
red lights will flash once only
and a beep will be heard.
Press the power on switch
‚ and the unit will turn on, it
will default to Max steam,
and the "on" light will flash
red whilst heating up.
4
Turn the temperature dial on
the iron in a clockwise
direction to 3-dot.
The iron's temperature
indicator light › goes off
when the selected
temperature is reached.
5
The appliance is ready to
use when the boiler ready
light „ turns green and the
iron temperature indicator
light › switches off.
Press the power switch ‚ to
6
choose the steam level from
'steam off', 'low steam' and
'maximum steam'.
Depress the steam button ⁄
7
for 1 minute to clear the
system of air (first time use
only) which will be
accompanied by a clicking
noise which is quite normal.
8
Begin first time ironing with
an old towel.
Ireland Helpline 1800 409 119
Advertisement
Table of Contents
