Control Panel; Installing An Ink Cartridge For The First Time - Epson Stylus Color 760 Product Information Manual

EPSON Stylus COLOR 760

Control Panel

paper out
light
color ink
out light
black ink
out light
cleaning
button
Follow these guidelines when you check the control panel
lights.
P is on The P power light is on when the printer is on and
ready to print. It flashes when the printer is
receiving a print job, charging ink, or cleaning the
print head.
S flashes When the S paper out light flashes and both ink
and out lights come on, you have a paper jam. Press
B and A the E load/eject button to try to clear the jam. If
are on that doesn't work, turn off the printer and gently
pull out all the paper. Make sure none of the
sheets are curled, creased, old, stuck together, or
too thin. Then reload the paper against the right
edge guide and slide the left edge guide against it.
Turn on the printer and press the E load/eject
button to resume printing.
S is on When the S paper out light comes on, your paper
is out or incorrectly loaded. Make sure none of the
sheets are curled, creased, old, stuck together, or
too thin. Then reload the paper against the right
edge guide and slide the left edge guide against it.
Press the E load/eject button to resume printing.
B or A flash
When an ink out light flashes, your ink supply is
low. Make sure you have a replacement cartridge
(black S020189, color S020191).
B or A are on
When an ink out light comes on, you need to
replace the ink cartridge. Make sure you have a
replacement cartridge (black S020189, color
S020191). See page 6 for instructions.
P and S When the P power and S paper out lights flash
and the B black and A color ink out lights come
flash and
B and A
on, jammed paper may be blocking movement of
are on the print head or you may not have removed the
yellow tape seal from the installed ink cartridge(s).
Turn off the printer, open the cover, and check
inside for any jammed paper. Then turn the printer
back on. If an ink out light remains on and the print
head moves into replacement position, replace the
ink cartridge(s) as described on page 8. If the lights
still flash and/or come on, contact your dealer or
EPSON.
4 - EPSON Stylus COLOR 760
power
light
load/eject power
button button
P S B A
When all the lights flash, your printer may have an
flash internal error. Make sure you removed all the
packing material as described on the unpacking
sheet in your printer box. Then turn off the printer,
wait a few seconds, and turn it on again. If the
lights still flash, contact your dealer or EPSON.
P S B A
When all the lights are off, the printer is not
are off receiving power. Try these solutions:
Make sure the printer is turned on.
Turn off the printer, plug in the power cord
securely, and turn on the printer again.
Make sure the outlet is operable and is not
controlled by a switch or timer. If in doubt, try
using another outlet.
Installing an Ink Cartridge for the First
Time
Follow these ink cartridge precautions:
Install both ink cartridges, and leave them installed for
all types of printing, or the printer won't work.
Remove the yellow tape seal from the top of the ink
cartridges or you'll permanently damage them. Don't
remove the clear seals on the bottom or ink will leak
out.
Don't open an ink cartridge clamp to remove a
cartridge except to replace it with a new one. Once
you remove a cartridge, you can't reuse it, even if it
contains ink.
Never turn off the printer when the
flashing, unless the printer hasn't moved or made any
noise for more than five minutes.
Keep ink cartridges out of the reach of children.
If ink gets on your hands, wash them thoroughly with
soap and water. If ink gets in your eyes, flush them
immediately with water.
1. Lower the output tray and open the printer cover.
2. Press the P power button to turn on the printer. The
P power light flashes and the B black and A color ink out
lights come on. The ink cartridge holders move left into
loading position.
Don't use an outlet that is controlled by a wall switch or
timer, or one on the same circuit as a large appliance, to
avoid damaging the printer's power supply.
Always use the
off. Never use an external switch, such as a power strip
switch.
8/99
P
power light is
P
power button to turn the printer on or