Advertisement
Quick Links
Programming
Project:
Control unit „105; 105A; i105; 205A; i205; i305"
Project leader:
Document:
Programming control unit „105; 105A; i105; 205A; i205; i305"
Version:
00
Revision:
Copy:
Programming Control Unit CH_SV V00
Programming
1/9
Hanover, 05.08.2010
Programming button 1
Programming button 2
Programming button 3
Advertisement
Related Manuals for mydocking.com DS0290020
Summary of Contents for mydocking.com DS0290020
- Page 1 Programming Hanover, 05.08.2010 Project: Control unit „105; 105A; i105; 205A; i205; i305“ Project leader: Document: Programming control unit „105; 105A; i105; 205A; i205; i305“ Version: Revision: Copy: Programming Programming button 1 Programming button 2 Programming button 3 Programming Control Unit CH_SV V00...
- Page 2 Programming GENERAL......................3 PROGRAMMING CONTROL UNIT ..............3 .......................... 3 TART PROGRAMMING 2.1.1 Open programming menu........................ 3 2.1.2 Select program no........................... 3 2.1.3 Confirm program no........................3 2.1.4 Select subprogram no........................3 2.1.5 Confirm subprogram no........................3 ........................3 INISH PROGRAMMING BY ERROR MESSAGES ..................
- Page 3 With the control unit you can operate hinged lip and telescopic lip levelers. With this short description you are able to configure the control unit. Use for the programming the service tool article- nr.: DS0290020 2 Programming control unit Start programming For starting the programming mode you have to close the door.
-
Page 4: Error Messages
Programming Note! If in the programming mode no push button is pressed anymore fro 60s, the changed settings will be reset and the control unit will leave the programming mode automatically. 3 Error messages Reading error messages This part describes how to start the reading of the last 10 error messages of the control unit 3.1.1 Start reading •... -
Page 5: Operating Cycles
Programming 4 Operating cycles Reading operating cycles This part describes how to start the reading of the operating cycles of the control unit 4.1.1 Start reading • Switch off control unit or lock the emergency Stop button, close door • Press programming button „3“ •... - Page 6 Programming • Release push button „AUTO“ • The function inflatable shelter On is stored Function inflatable shelter Off • Dock leveler in resting position and door closed • Press push button door „STOP“ 5s • The two LED´s on the control units are flashing at the same time •...
- Page 7 Programming 8 Index program number/ subprogram Program menu Subprogram Description Dock leveler hinged lip Dock leveler telescopic lip Push button door not active Push button door active Door function hold to run Door function impulse Inflatable shelter not active Inflatable shelter active Inflatable shelter with Rollo active Interlocking door/ leveler by limit switch Interlocking door leveler by photocell...
- Page 8 Programming Lift/ lip out 15,0s Lift/ lip out 17,0s Lift/ lip out 19,0s Lip in 5,0s Lip in 8,0s Lip in 11,0s Lip in 14,0s Lip in 17,0s Lip in 20,0s Automatic time 3,0s Automatic time 5,0s Automatic time 7,0s Automatic time 9,0s Automatic time 11,0s Automatic time 13,0s...
- Page 9 Programming Address 001 control unit communication Address 002 control unit communication Address 256 control unit communication F01 – over current hydraulic motor L1 F02 – over current hydraulic motor L2 F03 – over current hydraulic motor L3 F04 – phase sequence/ feedback signal contactor F05 –...
Need help?
Do you have a question about the DS0290020 and is the answer not in the manual?
Questions and answers