Safety Approvals; Control Panel - Epson Stylus Color 1160 Product Information

EPSON Stylus COLOR 1160
Electrical
Specification 120 V Model
Input voltage 99 to 132 V
range*
Rated frequency
range
Input frequency
range
Rated current 0.4 A
Power consumption Approx. 14 W (ISO/IEC 10561 Letter Pattern)
Approx. 3.5 W in standby mode
* Check the label on the back of the printer for your printer's
voltage.
Environmental
Temperature
Operation 50 to 95 °F (10 to 35 °C)
Storage* 4 to 104 °F ( 20 to 40 °C)
1 month at 104 °F (40 °C)
Transit* –4 to 140 °F (–20 to 60 °C)
120 hours at 140 °F (60 °C)
Humidity (without condensation)
Operation 20 to 80% RH
*
Storage 5 to 85% RH
*Stored in shipping container

Safety Approvals

Safety standards UL 1950, CSA C22.2 No. 950
EMC FCC part 15 subpart B class B

Control Panel

paper out
light
color ink
out light
black ink
out light
cleaning
button
4 - EPSON Stylus COLOR 1160
220 240 V Model
198 to 264 V
50 to 60 Hz
49.5 to 60.5 Hz
0.2 A
power
light
load/eject power
button button
Follow these guidelines when you check the control panel
lights.
P is on The P power light is on when the printer is on and
ready to print. It flashes when the printer is
receiving a print job, charging ink, or cleaning the
print head.
S flashes When the S paper out light flashes and both ink
and out lights come on, you have a paper jam. Press
B and A the E load/eject button to try to clear the jam. If
are on that doesn't work, turn off the printer and gently
pull out all the paper. Make sure none of the
sheets are curled, creased, old, stuck together, or
too thin. Then reload the paper against the right
edge guide and slide the left edge guide against it.
Turn on the printer and press the E load/eject
button to resume printing.
S is on When the S paper out light comes on, your paper
is out or incorrectly loaded. Make sure none of the
sheets are curled, creased, old, stuck together, or
too thin. Then reload the paper against the right
edge guide and slide the left edge guide against it.
Press the E load/eject button to resume printing.
B or A flash
When an ink out light flashes, your ink supply is
low. Make sure you have a replacement cartridge
(black S020189, color S020191).
B or A are on
When an ink out light comes on, you need to
replace the ink cartridge. Make sure you have a
replacement cartridge (black S020189, color
S020191). See page 6 for instructions.
P and S When the P power and S paper out lights flash
and the B black and A color ink out lights come
flash and
B and A
on, jammed paper may be blocking movement of
are on the print head or you may not have removed the
yellow tape seal from the installed ink cartridge(s).
Turn off the printer, open the cover, and check
inside for any jammed paper. Then turn the printer
back on. If an ink out light remains on and the print
head moves into replacement position, replace the
ink cartridge(s) as described on page 8. If the lights
still flash and/or come on, contact your dealer or
EPSON.
P S B A
When all the lights flash, your printer may have an
flash internal error. Make sure you removed all the
packing material as described on the unpacking
sheet in your printer box. Then turn off the printer,
wait a few seconds, and turn it on again. If the
lights still flash, contact your dealer or EPSON.
P S B A
When all the lights are off, the printer is not
are off receiving power. Try these solutions:
Make sure the printer is turned on.
Turn off the printer, plug in the power cord
securely, and turn on the printer again.
Make sure the outlet is operable and is not
controlled by a switch or timer. If in doubt, try
using another outlet.
9/99