Related Manuals for CeoTronics CT-Multi-PTT
Summary of Contents for CeoTronics CT-Multi-PTT
- Page 1 CT-Multi-PTT Bluetooth Operation Instructions English- USA - Canada Revision: 02/1015 DOK 1643-us...
-
Page 2: Table Of Contents
3 Scope of delivery .................... 5 4 Labeling of the product ................... 5 5 Product description ..................6 Description ..........................6 Fixation clamp .......................... 9 CT-Multi-PTT Bluetooth with CT-ClipCom Digital ..............10 5.3.1 EarMike .......................... 10 5.3.2 Earphone with BoomMike ....................11 5.3.3... -
Page 3: Warning - And Safety Instructions
If in doubt, ask our technical staff. Keep these operating instructions for later use. If repair work of any kind needs to be done to CeoTronics products, arrange for it to be performed only by the company CeoTronics or by a specialized workshop that is Revision: 02/1015 ... - Page 4 CeoTronics products may only be used for the specific application envisaged. Product damage! Do not immerse a CeoTronics product into water, if it is not expressly specified for this purpose. Risk of injury!
-
Page 5: Abbreviations And Terms
1 x CT-MultiPTT Bluetooth 1 x CT-Wireless PTT (Option) 1 x Operating instructions Dok1643 4 Labeling of the product Name of the product CT-MultiPTT Bluetooth Manufacturer CeoTronics AG Adam-Opel-Str. 6 63322 Rödermark Revision: 02/1015 DOK 1643-us 5 of 28... -
Page 6: Product Description
Bluetooth interface. The necessary CT communication set (not part of the scope of supply) is plugged into the corresponding socket. With the CT-Multi PTT Bluetooth, most of CeoTronics communication systems with 12-pin connector can be used on all cellular phones, supporting the Bluetooth Standard. - Page 7 Figure 2 Example Wearing method max. 40 cm The CT-Multi PTT Bluetooth complies with the Bluetooth specification 2.1. At some places, there exist restrictions regarding the use of Bluetooth devices. Ask your service provider or the competent authorities. An AA battery or AA storage battery provides the electrical power. For radio operation, the Bluetooth module must be in switched-on state, even if no cellular phone is used.
- Page 8 Figure 3 Plug for connection to a radio Pasted label with name of device Socket for communication set Battery compartment PTT button Bluetooth control button + storage battery / battery pilot lamp Green, continuous - battery fully charged Green, flashing - battery at half charge Red, flashing - battery almost flat, approx.
-
Page 9: Fixation Clamp
Figure 4 Figure 5 5.2 Fixation clamp The clamp can be rotated 360 °, infinitely variable. Figure 6 For rotating, loosen the knurled screw Revision: 02/1015 DOK 1643-us 9 of 28... -
Page 10: Ct-Multi-Ptt Bluetooth With Ct-Clipcom Digital
CT-Multi-PTT Bluetooth with CT-ClipCom Digital The CT-Multi-PTT Bluetooth is also available with integrated CT-ClipCom Digital technology and firmly attached communication set. The following two (2) system configurations are available: CT-ClipCom Digital EarMike consisting of an ear microphone and an additional speaker You hear radio messages and the ringing tone of the cellular phone on both sides. -
Page 11: Earphone With Boommike
Figure 8 Earphone on the left side Ear microphone on the right side Ear microphone with earphone ASR microphone 5.3.2 Earphone with BoomMike The earphone with boom microphone is available only for the left ear. Attached to the earphone is the boom microphone with protective cover (Figure 9/c) and the ASR microphone (Figure 9/b). -
Page 12: Use With Standard Ear Plug
6.1 Receipt of Goods Check incoming goods immediately upon receipt for completeness and/or transport damage! Inform the transport company and CeoTronics AG immediately of any transport damages! Risk of swallowing and choking! Keep packing material, e.g. filler materials und plastic bags, out of the reach of children;... -
Page 13: Operating Instruction
7 Operating Instruction 7.1 Change of the battery 7.1.1 Change of the battery – CT-Multi PTT Bluetooth Figure 13 1. Open the battery compartment by loosening the knurled screw. 2. Remove and replace the rechargeable Figure 14 battery / battery from the battery compartment. -
Page 14: Change Of The Battery In The Ct-Wireless-Ptt
7.1.2 Change of the battery in the CT-Wireless-PTT Open the battery compartment at the back of Figure 15 the CT-Wireless-PTT with help of the special tool by short turn to left. Remove the circuit board careful from the Figure 16 housing. -
Page 15: Connect The Ct-Multiptt Bluetooth To The Radio
7.2 Connect the CT-MultiPTT Bluetooth to the radio 7.2.1 12-pin connector Damage to connectors, sockets and/or cables Observe the following instructions when handling plug-in connections. Normally, the 12-pin connector is used in combination with radio adapters. For it, the adapter is attached to the radio and the 12-pin connector itself plugged into the radio adapter. -
Page 16: Switch-On
Figure 20 7.3 Switch-on Press simultaneously Bluetooth key and volume- up key until you hear an ascending three-tone sequence in the CT communication set. Then let the buttons go. The LED in the Bluetooth key indicates the condition of the battery/storage battery. -
Page 17: Change Operating Modes
Figure 22 7.6 Change operating modes You may switch between telephone mode (mode 1), telephone mode with MIC-switch (mode 2), and limited telephone mode with MIC-switch (mode 3). For it, proceed as follows The modes are signalized by the following beeps: Mode 1- 1 beep cellular phone mode Mode 2-... -
Page 18: Accept The Call
microphone. The microphone remains switched-on as long as the key is pressed. In the event the existing phone call has been interrupted intentionally or unintentionally, you hear in the CT communication set two times a descending sequence of tones. In the telephone mode with MIC switch, the Bluetooth key serves the following functions: Accept the call End the call... -
Page 19: Change The Pin For Ct-Multi Ptt Bluetooth
7.13 Change the PIN for CT-Multi PTT Bluetooth Store the newly set PIN in a safe place. In case the new PIN is lost, reprogramming is possible by CeoTronics, only. Figure 23 The PIN of the CT-Multi PTT Bluetooth is 83787432 in the state as delivered from factory. -
Page 20: Ct-Wireless-Ptt (Optional)
7.14 CT-Wireless-PTT (optional) For interference-free operation of the CT-Wireless-PTT receiver in the CT-Multi PTT Bluetooth, take care that the CT-Multi PTT Bluetooth is not located in close proximity to the transmitting antenna of a radio or cellular phone. Heterodyning the CT-Wireless-PTT radio signal by the comparatively strong transmit signal of a radio or cellular phone can compromise the sensitivity of the CT-Wireless-PTT receiver in the near field of the transmit antenna. -
Page 21: Subscribe The Ct-Wireless-Ptt To The Ct-Multi Ptt Bluetooth
7.15 Subscribe the CT-Wireless-PTT to the CT-Multi PTT Bluetooth Figure 25 1. Switch the CT-Multi PTT Bluetooth off, if it is 2. Press all three (3) lateral keys of the CT-Multi PTT Bluetooth simultaneously until the LED of the Bluetooth button starts flashing three (3) times red-green. -
Page 22: Delete One Ct-Wireless-Ptt From The Memory Of The Ct-Bluetooth Adapter
7.16 Delete one CT-Wireless-PTT from the memory of the CT-Bluetooth Adapter Figure 26 1. Switch the CT-Multi PTT Bluetooth off, if it is on. 2. Press all three (3) lateral buttons of the CT-Multi PTT Bluetooth simultaneously until the LED in the Bluetooth button starts flashing three (3) times red- green. -
Page 23: Delete All Ct-Wireless-Ptt From The Memory Of The Ct-Bluetooth Adapter
7.17 Delete all CT-Wireless-PTT from the memory of the CT-Bluetooth Adapter Figure 27 1. Switch the CT-Multi PTT Bluetooth off, if it is on. 2. Press all three (3) lateral keys of the CT-Multi PTT Bluetooth simultaneously until the LED in the Bluetooth button starts flashing three (3) times red- green. -
Page 24: Switch-On And Operation
Risk of hearing impairment For safety reasons reception volumes in excess of 85 dB(A) are possible with a whole series of CeoTronics products. However, the user can regulate the volumes. After switching on the communication system, set the reception volume to approx. 1/2 the available loudness volume and then test the audible volume, e.g. -
Page 25: End Of Operation
Product damage! Do not store CeoTronics products outside or in damp ambient conditions. At all times keep them clean, dry and at normal air humidity. CeoTronics products must not be stored in areas with a temperature of over +80° C (+176° F), e.g. in the summertime on the parcel shelf of a car. -
Page 26: Cleaning
Clean the connector pins with a commercial cleaning agent. 9 Disposal Should equipment, supplied by CeoTronics, be definitely put out of service you may return it to CeoTronics. We ensure recycling and/or disposal of outdated equipment in compliance with the applicable environment protection law. -
Page 27: Brief Instruction
11 Brief instruction Revision: 02/1015 DOK 1643-us 27 of 28... - Page 28 Tel. +1 757 549-6220 06295 Lutherstadt Eisleben Fax +1 757 549-6240 Tel. +49 34776 6149-0 E-Mail sales@ceotronicsusa.com Fax +49 34776 6149-11 E-Mail ctv.info@ceotronics.com Revision: 02/1015 DOK 1643-us Subject to change Copyright © 01/2014 CeoTronics AG, 63322 Rödermark, Germany, Internet www.ceotronics.com...