Bosch Professional GRL 350 HV Instructions Manual page 10

10 | English
Rotary laser
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Laser class
Laser type
Divergence
Tripod mount, horizontal
Non-rechargeable batteries (al-
kaline manganese)
Approx. operating time
Weight according to
EPTA‑Procedure 01:2014
Dimensions
(length × width × height)
Protection rating (excluding bat-
tery compartment)
A) At 20 °C
B) The working range may be reduced by unfavourable environ-
mental conditions (e.g. direct sunlight).
C) Along the axes
D) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
The serial number (18) on the type plate is used to clearly identify
your measuring tool.
Remote control
Article number
A)
Working range
Operating temperature
Storage temperature
Max. altitude
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Non-rechargeable batteries (al-
kaline manganese)
Weight according to
EPTA‑Procedure 01:2014
A) The working range may be reduced by unfavourable environ-
mental conditions (e.g. direct sunlight).
B) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
For clear identification of your remote control, see the serial
number (34) on the type plate.
Assembly
Remote Control Power Supply
Using alkali-manganese batteries is recommended to oper-
ate the remote control.
1 609 92A 69Y | (23.04.2021)
To open the battery compartment cover (36), press on the
GRL 350 HV
locking mechanism (35) and remove the battery compart-
90 %
ment cover. Insert the batteries.
D)
2
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
3R
compartment.
Always replace all the batteries at the same time. Only use
630–650 nm, < 5 mW
batteries from the same manufacturer and which have the
0.4 mrad (full angle)
same capacity.
5/8"-11
u
2 × 1.5 V LR20 (D)
30 h
1.8 kg
Measuring Tool Power Supply
It is recommended that you use alkaline manganese batter-
187 × 182 × 170 mm
ies to operate the measuring tool.
To remove the battery compartment (2), turn the locking
IP56 (protection against
mechanism (1) to position
dust ingress and water
out of the measuring tool and insert the batteries.
jets)
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
compartment.
Slide the battery compartment (2) into the measuring tool
and turn the locking mechanism (1) to position .
If the batteries become weak, the battery warning (12) will
light up red. The measuring tool can be operated for approx.
two more hours.
RC 4
If the battery warning (12) flashes red, the measuring tool
3 601 K69 S..
will automatically switch itself off after five minutes.
Always replace all the batteries at the same time. Only use
30 m
batteries from the same manufacturer and which have the
–10 °C to +50 °C
same capacity.
–20 °C to +70 °C
u
2000 m
90 %
B)
2
Operation
2 × 1.5 V LR6 (AA)
u
0.11 kg
u
u
Remove the batteries from the remote control when
not using it for longer periods. The batteries can cor-
rode and self-discharge during prolonged storage in the
remote control.
. Pull the battery compartment
Take the batteries out of the measuring tool when you
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage in the measuring tool.
Protect the measuring tool and remote control against
moisture and direct sunlight.
Do not expose the measuring tool or remote control to
any extreme temperatures or variations in temperat-
ure. For example, do not leave them in a car for extended
periods of time. In case of large variations in temperature,
allow the measuring tool and the remote control to adjust
to the ambient temperature before putting them into op-
eration. Before continuing work with the measuring tool,
always perform an accuracy check (see "Accuracy Check
of the Measuring Tool", page 14).
The precision of the measuring tool may be compromised
if exposed to extreme temperatures or fluctuations in
temperature.
Avoid substantial knocks to the measuring tool and
avoid dropping it. Always carry out an accuracy check
Bosch Power Tools