各部件名稱及功能 ▼ 前面 ① ① 燈號........綠燈亮:動作中 (開啟電源) 綠燈閃:啟動 關機中、設定中、 音樂 CD 讀取中 紅燈亮:發生錯誤 橘燈亮:偵測到新韌體 橘燈閃:韌體更新中 熄 燈:切斷電源 紅燈亮時 內部磁碟發生異常,無法找到 USB HDD,備份用的 USB 硬碟容量不足。 如果取出 USB HDD 後仍無法解決問題,請聯繫代理商的客服中心。 橘燈亮時 請關閉電源。開始更新韌體。 在電源指示燈熄滅之前,請勿停止供電。...
Page 7
各部件名稱及功能 ▼ 背面 ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ② 防盜鎖孔......可加裝防盜措施防盜鎖 (Kensington Lock)。 ③ 電線掛鉤孔......安裝配件的電線掛鉤。 ④ 電源連接器......連接配件的 AC 變壓器。 ⑤ LAN Port ......以 LAN Cable 連接 Wi-Fi 路由器。 ⑥ USB 2.0 Port ..... 連接 USB 裝置。 ⑦...
安裝 ∼ (必要時) 連接 USB 裝置 (必要時) 連接 USB 裝置 必要時,可將 USB HDD 或 USB CD/DVD/BD 光碟機連接到 Soundgenic 的 USB 3.0/2.0 或 USB 2.0。 ● USB 裝置之用途 • USB HDD ( 分享用 ) 和 ( 備份用 ) 可各接一台。 (分享用) 可讀取 USB HDD 內的音樂,並傳送到播放器。...
儲存音樂檔案 tada Music App 的準備工作 準備 I-O DATA 專為智慧型手機和平板電腦開發的 「 tada Music App」 控 制應用程式。 關於 data Music App • 可作為控制應用程式操作音樂播放 • 可操作和執行本產品上的設定 • 可執行 CD 擷取與檔案操作等動作 使用智慧型手機或平板電腦開啟 App Store 或 Google Play 商 店, 並安裝「 data Music App」。 啟動 data Music App。...
儲存音樂檔案 ∼ 從 USB 隨身碟或 USB 硬碟匯入 從 USB 隨身碟或 USB 硬碟匯入 將 USB 隨身碟或 USB 硬碟上儲存的音樂複製到 Soundgenic。 ● 需備物品 • 含有音樂的 USB 隨身碟或 USB 硬碟 ● 步驟 「USB 3.0/2.0」 或 「USB 2.0」 連接 USB 隨身碟或 USB 硬碟 USB 隨身碟...
詳細指南→ 備份音樂 匯入到 Soundgenic 內建磁碟的音樂可儲存於連接的 USB 硬碟中。 登錄備份用 USB 硬碟 連接用於備份的 USB 硬碟 「USB 3.0/2.0」 ※ 請使用容量等於或大 或 於 Soundgenic 容量的 「USB 2.0」 USB 硬碟。 USB 硬碟 注意:請勿在此步驟中連接其他 USB 裝置 登錄用於備份的 USB 硬碟 (備份用) 時,便會刪除其中的資料。為了防止 不慎刪除重要資料,進行此操作時請只連接 1 台 USB 硬碟。...
Page 55
Table of Contents Introduction ......2 Saving Audio Files from Intended Use of Sound- a Windows ......25 genic ........2 Saving Audio Files from Check the Accessories ..3 a macOS ......27 Composition of the Confirming free space ..29 Instruction Manual .....
This section explains information about Soundgenic. Intended Use of Soundgenic Soundgenic is a network audio server that streams music to a net- work audio device through a home network. It allows you to save music and enjoy it with network audio devic- Soundgenic can also be used as a network audio player by con- necting a USB-DAC.
● Describes the basic way to use this unit. Detailed Manual : ● Please see the "Detailed Manual" on the Internet when you want a more detailed description. You can download these instruction manuals from the fol- lowing website. https://www.iodata.jp/ssp/soundgenic/en/#manual...
Names and Functions of Each Part ▼ Front 1. Indicator ......Green light: Power is on Green blinking light: Starting up and stop- ping, processing settings, recognising music Red light: Error Orange light: The firmware can be updated Orange blinking light: Updating firmware Unlit: Power is off Red light This may indicate a problem with the built-in disk, an inability to lo-...
Page 59
Names and Functions of Each Part ▼ Back 2. Security slot ....A Kensington lock is installed to prevent theft. 3. Cable hook hole ..Used to install the included cable hook. 4. Power connector ..Used to connect the included AC adapter. 5.
Connecting to a Wi-Fi Router Connect the Wi-Fi router LAN port and Soundgenic’s “LAN” using the included LAN cable. Operate Soundgenic with a tablet or other device to perform ac- tions such as downloading music and data updates. LAN cable...
DAC). Of course, it is also possible to connect to both. ● Connecting to a Network Audio Player Connect the Wi-Fi router connected to Soundgenic to the net- work audio player using the LAN cable. For details of network audio players, please see the instruction manual.
Page 62
Install this Unit > Connecting to a Wi-Fi Router ● Connecting to a USB-DAC Connect the Soundgenic’s “USB 3.0/2.0” or “USB 2.0” to the USB-DAC. Soundgenic can also be used as a network audio player, and can play music using a USB-DAC. “USB 3.0/2.0”, or “USB 2.0” USB-DAC...
Install this Unit > Connecting to a Power Outlet Connecting to a Power Outlet Connect the included AC adapter to Soundgenic’s “DC IN 12V” port, then connect the AC adapter to a power outlet. (The power turns on when it is connected to a power outlet.)
Page 64
Install this Unit > Connecting to a Power Outlet Turning the power on for subsequent use Press POWER Blinking green Lit green Turning the power off Press POWER for 1 second Blinking green Not lit ● It takes a moment for the power to be turned off Do not disconnect the AC adapter or turn off the switch on a power strip until the indicator lamp is no longer lit.
Connecting to a USB Device (as Necessary) If necessary, it is possible to connect a USB HDD or USB CD, DVD, or BD drive to Soundgenic’s USB 3.0/2.0 or USB 2.0 ports. ● Use of USB Devices • USB HDD It is possible to connect one that is for sharing and one as a backup.
Saving Audio Files > Preparing fitada Music App Preparing fitada Music App Get ready to use the I-O DATA produced “fitada Music App” con- trol application for smartphones and tablets. About fidata Music App ● Can operate music playback as a control application ●...
Page 68
Saving Audio Files > Preparing fitada Music App Tap [Skip this proce- dure]. Tap [Next]. Select Soundgenic as the music server. Tap [Next].
Page 69
Saving Audio Files > Preparing fitada Music App Select the renderer (play- er) for playing music. * If this product is connected to a USB- DAC, this product will also be displayed as a player. Tap [Next]. Confirm the selected server and renderer.
Page 70
Saving Audio Files > Preparing fitada Music App The basic operations will be introduced, so read through them. Tap [Next]. 1 0 Tap [Start using the app]. This completes the preparation of fidata Music App.
* Used to supply music information in Folder.jpg format. You cannot open or copy this file using a computer, etc. However, this file can be moved or deleted in Soundgenic, so you can change to the desired configuration. * If the target music does not have any artwork data sup- plied by Gracenote, the Folder.jpg file is not stored.
Page 72
Saving Audio Files > Loading from a music CD ● Procedure “USB 3.0/2.0” , “USB 2.0” Connect a USB CD, DVD, or BD drive to Soundgenic. USB CD/DVD/BD drive Insert a music CD into the USB CD, DVD, or BD drive. Launch fidata Music App. on the lower left.
Page 73
How to rip only a portion of the music After tapping [Release all], check only the music you want to rip. Tap [Start ripping] ⇒ Music CD importing (ripping) begins. There is no problem if the screen closes during ripping The ripping process will be continued by Soundgenic.
Page 74
Saving Audio Files > Loading from a music CD Standard importing time Loading time for a music CD Condition 1 Condition 2 Drive A 8 min. 38 sec. 8 min. 40 sec. Drive B 16 min. 42 sec. 16 min. 43 sec. *1 Using a 70 min.
Page 75
- Some tracks were not imported due to dirt or damage on the music CD. Check the reading side of the music CD. Also, check the tracks that were not imported. - You have ejected media or removed the CD/DVD/BD drive during import processing. Your music is now in Soundgenic.
Saving Audio Files > Importing from a USB flash drive or USB HDD Importing from a USB flash drive or USB HDD Music stored on a USB flash drive or USB HDD is copied to Sound- genic. ● What to Prepare •...
Page 77
Saving Audio Files > Importing from a USB flash drive or USB HDD Tap [File operation] * If there is no information in the gray area, tap [RA] under the gray. Display the location you wish to save the music * The music is put in the “contents”...
Page 78
Saving Audio Files > Importing from a USB flash drive or USB HDD Tap [RA] Tap [USB1 to 3] Check the music or folders in the USB that you want to copy 10 (copy) 11 (paste) The checked music is copied Your music is now in Soundgenic.
● What to Prepare • The personal computer should be connected to the same rout- er as Soundgenic. Install "LAN DISK CONNECT". This is an application to access Soundgenic. Please access the following Web page, and install it on your personal computer. https://www.iodata.jp/ssp/soundgenic/en/#landiskconnect ●...
Page 80
Saves music imported from a USB HDD or other source. (Created when music is imported from a USB HDD or other source.) ● uploaded Saves music uploaded to Soundgenic by operating another DLNA device. Your music is now in Soundgenic.
● What to Prepare • The Mac should be connected to the same router as Sound- genic. Install "LAN DISK CONNECT". This is an application to access Soundgenic. Please access the following Web page, and install it on your Mac. https://www.iodata.jp/ssp/soundgenic/en/#landiskconnect ●...
Page 82
Saves music imported from a USB HDD or other source. (Created when music is imported from a USB HDD or other source.) ● uploaded Saves music uploaded to Soundgenic by operating another DLNA device. Your music is now in Soundgenic.
[RA] under the gray. Deleting music in Soundgenic Music can be deleted using the fidata Music App file operation. For more information, please see the Detailed Guide. The free space in Soundgenic was confirmed with this operation.
When music cannot be found ● After tapping the upper right of the screen, tap [Soundgenic] > [Music]. ● If is not in the upper right of the screen, flick the screen to switch panes (screen division).
Page 85
Playing Music Tap the music to register it to the playlist. ⇒ The tapped music is registered on the right side (playlist pane). If music cannot be registered in the lower right, and select a renderer (player). Swipe the screen to display another one-side pane (playlist pane) * For tablets, 2 panes are displayed, so this process is unnecessary.
Page 86
Playing Music Deleting a music registration ● For iOS Flick the music to the left, and tap the displayed [Delete] option. ● For Android Flick the music to the left edge. Changing music registration rules (new): Plays the tapped music. Erases other music from the playlist.
Page 87
Playing Music Tap the track informa- tion The track information and artwork is dis- played larger. Enjoy the music. Returning to the original screen Tap near the track name to return to the original screen.
For more information, please visit https://spotify.com/connect. * You need to subscribe to the Spotify Premium or Spotify Free service. * Soundgenic and your mobile device must be connected to the same network. * The Soundgenic renderer must be running in OpenHome mode.
Detailed Manual » Backing up music Music imported to Soundgenic’s internal disc can be saved on a connected USB HDD. Registering a USB HDD for backup Connect the USB HDD USB 3.0/2.0, to use for backup * Use a USB HDD with USB 2.0...
Page 90
Backing up music Tap the gray area * If you cannot tap it, tap [RA] under the gray. Tap [Device Settings] Tap [USB DEVICE SET- TINGS]. Select [Registration of the device for backup]. Tap [NEXT].
Page 91
Backing up music Read the precautions, and tap [REGISTRATION]. Tap [Yes]. 10 Wait until the USB HDD is registered 11 Check that “Succeeded to register the device for backup.” is dis- played...
To back up music, avoid connecting the USB HDD (for backup) sporadically. The difference shall be backed up. For information about how to remove the USB HDD while the power to Soundgenic is on, see the Detailed Manual. Be sure to occasionally organize backed up music.
Page 93
Backing up music Launch fidata Music App on the lower left * When not displayed on the lower left, flick the screen to switch screens. Tap the gray area * If you cannot tap it, tap [RA] under the gray. Tap [Device Settings] Tap [USB DEVICE SET- TINGS].
Page 94
Backing up music Select [Restoration of backup data] Tap [NEXT]. Read the precautions, and tap [RESTORE] Tap [Yes]. ⇒ Music restoration begins.
Page 95
Backing up music 10 The indicator lamp will Blinking green → Lit green blink, so wait until it returns to being lit * Do not remove the USB HDD while the indicator is blinking. 11 Remove the USB HDD (for backup) USB HDD When you want to continue backup After removing the USB HDD (for backup) once, reconnect it.
Appendix Operating Environment For more information, please see the product page https://www.iodata.jp/ssp/soundgenic/en/#spec ▼ If using as a network audio server Can be used by connecting to a UPnP AV compliant network au- dio player. • Supported file formats (extensions)* wav mp3 wma m4a m4b ogg flac aac mp2 ac3 mpa aif...
Page 97
Appendix > Operating Environment ▼ If using as a network audio player (USB-DAC connection) Can be used by connecting to a USB-DAC that supports USB Au- dio Class 2.0. You can use an application supported by Open Home Media or a DLNA compatible DMC (Digital media Controller) application as the controller app.
Safety For Safe Use The precautionary items described here are intended to ensure safe and correct use of this product, and to prevent harm to users and dam- age to property. Please be sure to follow these precautions when using this product. •WARNING and CAUTION indications •Meaning of sym- bols...
Page 100
Safety Do not connect while it is Be sure to turn off the power broken or malfunctioning. to the personal computer, peripheral devices, and this Be sure to remove all devices if this product is broken or mal- product, and remove the plug from the electrical outlet functioning.
Page 101
Safety Do not use near items that Do not connect to a loose have high heat or moisture electrical outlet. retaining properties, such as Ensure the power plug is firmly rugs, sponges, cardboard, or inserted all the way into the polystyrene.
Page 102
Safety CAUTION Do not step on this product. Do not touch a fixed spot on It could cause damage or this product continuously for a long time. injury. Be especially cautious of small children. This product may feel hot when it is used for a certain amount of time.
Safety Caution in Use [Important] Regularly back up data. This product is a precision device. Data may be lost depending on the reason for sudden failures, etc. As a precaution, always perform regular back ups* of important data that is saved in this product. Our company takes no responsibility for any loss or damage to any data saved on this product or other products connected to this product.
Page 104
It could cause a failure or loss of data. • It may not be possible to access Soundgenic due to firewall software. If this happens, authorize access for ports No. 137 to 139, and No. 445 on the...
This firmware for this unit will be updated to the latest version. RA-xxxxxx is not displayed. • Your smartphone, tablet, or personal computer is not con- nected to the same network as Soundgenic. Connect your smartphone, tablet, or personal computer to the same router as Soundgenic.
Page 106
Troubleshooting The front indicator is lit in red. • There may not be enough space on the USB HDD for storing backup data. Please access the backup destination (bkup folder) from a PC, and delete any unnecessary files. [Saving Audio Files] (page 12) •...
Page 107
Troubleshooting There is noise or the sound suddenly cuts out while playing mu- sic from a USB-DAC. • This is because the music is being played at a high rate. If the USB-DAC is connected to the USB 2.0 port, it may be improved by switching it to connect to the USB 3.0/2.0 port.
Page 108
【關於使用軟體】 • 本產品包含 GNU General Public License Version3(GPLv3) 為基準的軟體。 已完成變更的 GPL 對象模組 , GNU General Public License 以及相關發佈相 關的條款 , 請在如下網頁進行確認。 http://www.gnu.org/licenses/gpl-3.0.en.html 關於這些用原始碼發佈的軟體 , 敝司及其軟體製作者恕不負任何支援責任 , 敬請 理解。 • 本產品包含為了使用 OpenSSL Project, OpenSSL Toolkit(http://www. openssl.org) 所開發的軟體。 本產品包含由 Eric Young(eay@cryptsoft.com) 所製作的加密軟體。 本產品包含由...
Page 109
設備名稱: ,型號 (型式) : Soundgenic 音樂伺服器 HDL-RA2TB Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 六價鉻 多溴聯苯 多溴二苯醚 單元 Unit 鉛 汞 鎘 Hexavalent Polybrominated Polybrominated Lead Mercury Cadmium (Pb) (Hg) (Cd) chromium biphenyls diphenyl ethers...
Page 110
本頁特意留空。 This page is intentionally left blank.
Page 111
本頁特意留空。 This page is intentionally left blank.
Need help?
Do you have a question about the Soundgenic and is the answer not in the manual?
Questions and answers