Page 2
CAUTION CAUTION Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING When using electrical products, basic safety precautions should always be followed, including the following: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 3
TAKING CARE OF YOUR DRUM DO NOT ATTEMPT TO OPEN THE UNIT OR MAKE ANY CHANGE IN THE CIRCUITS OR PARTS OF THE UNIT. - direct sunlight (near a window), SERVICE AND MODIFICATION - high temperatures (near a heat source, outside, or This product should be serviced by qualified service in a car during the daytime), personnel when,...
INSTALLATION CRASH A-12 Cymbal-edg HI-HAT SOUND MODULE A-8 Hi-Hat HD-006 RIDE A-12 Cymbal TOM 1 A-8 Tom TOM 2 A-8 Tom SNARE KICK B-8 Tom B-6 Kick TOM 3 A-8 Tom RACK SYSTEM HI-HAT CONTROLLER B-HH Ctrl KICK PEDAL P-6C Kick pedal * KICK PEDAL IS OPTIONAL ACCESORY The drawing shows a complete drum kit after installation.
Page 6
INSTALLATION RACK SYSTEM L-Rod Wing nuts Cross beam Pad clamp Rack clamp Folded rack in package Crash and Ride rod Hi-Hat rod Foot Other parts of the rack system...
Page 7
INSTALLATION RACK INSTALLATION 5 Insert the cymbal rods 4 Rotate the L-Rods and adjust their position to proper positions, then tighten the wing nuts 3 Move and rotate the pad clamps to proper locations 6 Move and rotate the cymbal clamp to proper location, then tighten the wing nuts 1 Open the arms, adjust the position of arms...
Page 8
INSTALLATION COMPONENTS INSTALLATION Hi-Hat Installation Crash and Ride Installation 1. Remove the wing nut, 1. Remove the wing nut, washer washer and felt pad and felt pad 2. Put the cymbal pad into the 2. Put the Hi-Hat into the rod rod along with parts removed in along with parts removed in step 1.
SOUND MODULE CONTROL PANEL CLICK TEMPO MASTER VOLUME PATTERN CRASH RIDE HIHAT TOM 2 TOM 1 VOICE VOLUME DRUM OFF TOM 3 HI-HAT PEDAL SNARE KICK STOP PLAY RECORD SAVE (1) Display: The display is a 3-digital 7-Segment LED type showing Information such as Kit number, Voice number etc.
SOUND MODULE BOTTOM PANEL D C 9 V LINE OUT L I N E I N T R I G G E R HEADPHONE U S B P O W E R O F F (1) Power Switch: Turn On/Off the sound module Note: After you turn the power off, do not turn it on immediately.
PLAY PAD TURN ON THE POWER Playing Snare Drum Strike the central position (head) of the pad to make head sound, strike the rim of the pad to make a rim (1) Turn down the external audio device connected sound. with the drum.
DRUM KIT This drum has 20 preset drum kits for your choice. The kit is a combination of different instrument voices assigned to each pad which has unitary style for performance. Any kit could be edited and saved. After the power is turned on, the kit mode is engaged automatically the KIT button is lit and the kit number is shown on the display.
DRUM KIT The following procedure is for voice assignment. The way of changing its volume is the same. While the VOICE button and the selected pad button blink, its current voice number will appear on the display. Use the +, - button to change the voice number ranging 1 - 184. Press both + and - button simultaneously, its original voice will be restored.
PATTERN There are 50 built-in patterns for your enjoyment and exercise. PLAY THE PATTERN Press the PATTERN button to engage the pattern mode and Enter the pattern mode its indicator will light up. The pattern number with “P” in front will appear and blink on the display.
METRONOME Press the CLICK button to activate the metronome, its indi- cator will light up and flash according to current tempo. Note: During the pattern playing, the metronome cannot sound but the CLICK button will flash if the metronome is engaged. Activate the metronome Press the button again to stop it.
RECORD This drum provides facilities to record one piece of your per- formance and save it as pattern 51. The recording could be accompanied with pattern. Before recording, you should pre- pare necessary settings including selecting drum kit, metro- nome and tempo setting, pattern selecting etc. RECORD STANDBY STOP PLAY...
RECORD Press the RECORD button again or press the STOP button to terminate the recording. The RECORD button blinks and is ready for the next recording. The new recording over-writes the contents of the previous recording in unit of measure. In this way, you can edit your recording.
USB & MIDI MIDI stands for Musical Instrument Digital Interface. This is a world wide standard communication interface that enables electronic musical instruments and computers to communicate with each other so that instruc- tions and other data can pass between them. This exchange of information makes it possible to create a system of MIDI instruments and devices that offers far greater versatility and control than that is available with isolated instruments.
Page 20
VOICE LIST Description Description Description Open Hi-Hat 12 Low Tom5 CLOSED HI-HAT Closed Hi-Hat 1 Open Hi-Hat 13 Low Tom6 Closed Hi-Hat 2 Low Tom7 HI TOM Closed Hi-Hat 3 Hi Tom 1 Low Tom8 Closed Hi-Hat 4 Hi Tom 2 CRASH Closed Hi-Hat 5 Hi Tom 3...
Need help?
Do you have a question about the HD-006 and is the answer not in the manual?
Questions and answers