Rear Drum Assembly ......... 44-45 NOTE Drive Assembly ..........46-47 Specification and Transmission Assembly........48-49 part number are subject to change Water System Assembly ........50-51 without notice PAGE 4 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Figure 1. R2000 Roller Dimensions . N I l l a l l a . n i l l a . n i i r e . n i PAGE 8 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Potential hazards associated with MQ R2000 vibration roller operation will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 9...
Page 10
ALWAYS wear approved eye and hearing protection. This roller, other property, or the surrounding environment could NOTE be damaged if you do not follow instructions. PAGE 10 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Multiquip for this equipment. Damage to the equipment and/or injury to user may result. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 11...
Page 12
■ In the event of hydraulic hose or line failure, promptly return the travel lever to the “neutral” position, stop the engine and set the parking brake. PAGE 12 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Page 13
■ NEVER stand below roller when it is being lifted. DANGER : DO NOT allow personnel to stand under or near any suspended machine . Serious injury or death may result. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 13...
Machine Safety Decals The R2000 static roller is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
Travel speed is infinitely variable from 0 to 4 mph. The neutral position of this lever will cause the roller to stop. Figure 2. Recommended Slope R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 15...
Page 16
, even death, if side-side operation is used (Figure 3). DO NOT use this roller for side to side applications. PAGE 16 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Page 19
15. Steering Zerk Fitting – Grease this fitting as recommended in the maintenance section of this manual. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 19...
11. Circuit Breaker– Protects the battery charging circuit. See Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop Honda owner's manual for additional information. the flow of fuel. PAGE 20 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
3. When refueling, be sure to use a strainer for filtration. DO Figure 6. Engine Oil Dipstick (Removal) NOT top-off fuel. Wipe up any spilled fuel. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 21...
Page 22
Protect water from freezing by adding antifreeze or draining water tank when not in use. Use only clean water in water tank. PAGE 22 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Starting the Engine 1. Place the engine fuel valve lever (Figure 11) to the "ON" position. Figure 13. Choke Lever Figure 11. Engine Fuel Valve Lever R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 23...
2. To make the roller move in a forward direction , move the transmission control lever forward as shown in Figure 15. Make sure lever is securely place into notch. PAGE 24 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Page 25
2. Place the engine fuel valve lever (Figure 11) in the OFF position. brake R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 25...
A shield or cover should be placed over the reservoir cover during cleaning operation or in other situations where water maybe introduced into the unit. PAGE 26 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Page 27
5 lbs. of force applied to the center of the span between the sprockets toward the front of the roller. 8. If the tension is still incorrect, readjust. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 27...
Page 28
If these gases and liquids come in contact with a flame Figure 22. Battery Fluid Levels or spark, an explosion could occur. PAGE 28 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Cover the roller and place it a clean dry area, that is protected from harsh elements. Remove ignition key, and store in a safe place. R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06) — PAGE 29...
<, belong to the same assembly or kit. If more than one of the same reference number is listed, the NOTE last one listed indicates newest (or latest) part available. PAGE 32 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Multiquip’s designated receiving point. on hand at the time of any price change. PAGE 88 —R2000 RIDE-ON STATIC ROLLER — OPERATION & PARTS MANUAL — REV. #2 (03/20/06)
Need help?
Do you have a question about the R2000 and is the answer not in the manual?
Questions and answers