Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cabletron Systems 9C214-3
Summary of Contents for Cabletron Systems 9C214-3
- Page 1 SmartSwitch 9000 9C214-3 AC Power Supply Installation Guide 9032529-01...
- Page 3 Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice.
-
Page 4: Fcc Notice
Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. -
Page 5: Declaration Of Conformity
DECLARATION OF CONFORMITY Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives. Manufacturer Mr. - Page 6 Notice...
-
Page 7: Table Of Contents
Chapter 2 Installing the 9C214-3 Power Supply Unpacking the 9C214-3 Power Supply ... 2-1 Installing to the SmartSwitch 9000 Chassis... 2-1 Powering Up the 9C214-3 Power Supply ... 2-3 Chapter 3 9C214-3 Power Supply Operation Operating Functions ... 3-1 System Diagnostic Controller ... 3-2 Internal Temperature Sensor ... - Page 8 Contents...
-
Page 9: Chapter 1 Introduction
The 9C214-3 Power Supply The 9C214-3 power supply, shown in Figure 1-1, is a 2000 watt, triple output supply that provides power to the SmartSwitch 9000 chassis. At least one power supply must be installed; however, additional power supplies can be installed to achieve redundancy. - Page 10 Introduction Figure 1-1. The 9C214-3 Power Supply Power Supply Status LED STATUS 100% Load 9C214-3 POWER SUPPLY MODULE 207-264v-12A 50-60 Hz Status Power Supply Level Indicator Power Switch Power Socket...
-
Page 11: Features
The 9C214-3 power supply accepts AC input voltage ranging from 207–264 volts at 50/60Hz. Hot Swapping 9C214-3 power supplies can be installed or removed from the back of the chassis while another power supply is operating without affecting network operation. ®... -
Page 12: Power Distribution System
Introduction Power Distribution System The SmartSwitch 9000 uses a distributed DC power distribution system (Figure 1-2) similar to those used in super computers. Three separate power buses are used to distribute DC power. The 48-volt DC System Power Bus, located on the backplane, powers all modules and the system cooling fans. -
Page 13: Getting Help
Getting Help For additional support related to this device or document, contact Cabletron Systems using one of the following methods: World Wide Web Phone Internet mail Login Password To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@cabletron.com Make sure to include the document Part Number in the email message. - Page 14 Introduction...
-
Page 15: Chapter 2 Installing The 9C214-3 Power Supply
Installing the 9C214-3 Power Supply At least one power supply must be installed on the rear of the SmartSwitch 9000 chassis. Additional power supplies can be added to achieve redundancy. A power supply is installed by plugging it into either the left or right power supply connector on the SmartSwitch 9000 chassis, as shown in Figure 2-1. - Page 16 Secure the power supply to the chassis by tightening the two screws on the top and two screws on the bottom of the power supply. For proper chassis grounding, the four screws must be properly tightened. Figure 2-1. Installing the 9C214-3 Power Supply STATUS 100%...
-
Page 17: Powering Up The 9C214-3 Power Supply
Interface Modules have been properly installed. NOTE The 9C214-3 Power Supply is powered up by following the steps below: 1. Plug one end of the power cord (supplied with the power supply) into the AC power socket on the lower right front corner of the power supply. - Page 18 Installing the 9C214-3 Power Supply...
-
Page 19: Chapter 3 9C214-3 Power Supply Operation
9C214-3 Power Supply Operation The 9C214-3 power supply can operate with input voltages ranging from 207–264 VAC at 50/60 Hz. Each 9C214-3 provides a maximum of 2000 watts of power to the SmartSwitch 9000. When two power supplies are installed, the system uses a current sharing scheme where, under all load conditions, each supply provides 50% (±... -
Page 20: Internal Temperature Sensor
Diagnostic Controller fails, fan speed defaults to 100% to ensure protection of the power supply. LANVIEW LEDs The LANVIEW LEDs on the back of the 9C214-3 power supply may be used as an aid for troubleshooting. There are three LANVIEW LEDs visible to the user (Figure 3-1): the PWR Status LED, the SMB Status LED, and the Power Supply Level Indicator LED. -
Page 21: Pwr Status Led
SMB Status LED are listed in Table 3-2. LED Color Green Yellow/Green Yellow Yellow (Flashing) Red (Flashing) 9C214-3 Power Supply Operation Table 3-1. PWR Status LED State Functional The 56-volt, 5-volt, and 3.3-volt outputs are within established tolerances. Crippled... -
Page 22: Power Supply Level Indicator Led
9C214-3 Power Supply Operation Power Supply Level Indicator LED The Power Supply Level Indicator LED indicates the percentage of the power supply load. The possible states and descriptions of the Power Supply Level Indicator LED are listed in Table 3-3. -
Page 23: Chapter 4 Specifications
CAUTION The 9C214-3 power supply, when properly installed on the SmartSwitch 9000 chassis, complies with the following safety specifications and standards: • UL 1950 •... -
Page 24: Physical
11.2A @207 volts 8.7A @264 volts Fusing The AC input to the 9C214-3 power supply has a non-user serviceable 250 volt 15-amp fuse. AC Input Connection The AC input connector is an IEC type entry requiring the use of the Cabletron- approved power cord provided with the 9C214-3 power supply. -
Page 25: Output Voltage
Output Voltage Each 9C214-3 power supply is capable of generating the following output voltages: 56.0 volts @35A 3.3 volts @17A 5.1 volts @18A Specifications... - Page 26 Specifications...