PROEL FLASH15HDA User Manual page 11

6. PRESET selector
This switch allows the selec on between four diff erent DSP se ngs (equalisa on curves, dynamics etc.), suited to four
diff erent uses.
FLAT
Suited for live sound reinforcement, this preset includes a dynamic equalizer.
When the system is used at low or mid level, the deep lows and the top highs are
enhanced, resul ng in an deep and detailed response, ideal for the reproduc on
vocals and live instruments. When the level of the signal sent to the amplifi er is
increased and it approaches the limiter ac on, the enhancement of low and high
frequencies is reduced, thus increasing the dynamics and the effi ciency of the
whole system. Together with that, the mid-high frequencies are slighlty decreased,
thus reducing the harshness that can occur when the sound is very loud and
making it more enjoyable.
DJ
Suited for the reproduc on of recorded music, this preset includes a dynamic
equalizer.
When the system is used at low or mid level, the deep lows and the top highs are
enhanced, resul ng in an richer and brighter response, ideal for the reproduc on
of background music or for a DJ set. When the level of the signal sent to the
amplifi er is increased and it approaches the limiter ac on, the enhancement of low
and high frequencies is reduced, thus increasing the dynamics and the effi ciency
of the whole system. Together with that, the mid-high frequencies are slightly
decreased, thus reducing the harshness that can occur when the sound is very loud
and making it more enjoyable.
SPEECH
This preset has been designed for applica ons (such as conferences) where a
dynamic microphone is directly connected to the speaker input and it provides the
correct equaliza on for enhancing the human voice intelligibility.
MONITOR
Suited for the use of the system as a stage monitor, in this preset the deep lows
are a enuated in order to compensate the fl oor posi on, the mid-low frequencies
are enhanced for a be er presence and the mid-high frequencies are reduced for
an improved feedback rejec on.
7. SIGN / LIMIT indicator
GREEN LED illuminates to indicate the presence of the signal at the amplifi er
input.
RED LED illuminates when the internal amplifi er's output is limited or when the
input AD converter clips.
NOTE: When this LED fl ashes reduce the input signal level.
NOTE: If you hear annoying and excessive distor on check the MIC/LINE switch posi on, most probably you are sending
to the speaker a high line level signal using the MIC sensi vity, so switch it to LINE sensi vity.
8. ON indicator
GREEN LED: when lighted indicates that the amplifi er has been turned on and AC power is available.
9. POWER switch
Speaker is "ON" when the switch is in the "I" posi on.
NOTE: When you shut down your equipment, turn off the speaker fi rst. When powering up, turn on the speaker last.
10. AC~ socket
Here's where you plug in your speaker's mains supply cord. You should always use the mains cord supplied with the
speaker. Be sure your speaker is turned off before you plug in the cord.
11. FUSE holder
Here is placed the mains protec on fuse. Please follow the instruc ons on page 9 of this manual to replace it.
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
40 50 100 200 500 1k 2k
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
40 50 100 200 500 1k 2k
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
40 50 100 200 500 1k 2k
120.0
dBSPL
110.0
100.0
90.0
80.0
70.0
40 50 100 200 500 1k 2k
Hz 5k 10k 20k
Hz 5k 10k 20k
Hz 5k 10k 20k
Hz 5k 10k 20k
11