Bosch HEI8056U Installation Instructions Manual

Bosch HEI8056U Installation Instructions Manual

Hide thumbs Also See for HEI8056U:

Advertisement

Electric and Induction Ranges
Installation Instructions
Slide-In Ranges
HEI8056C, HEI8056U, HEIP056C, HEIP056U, HIIP056C,
HIIP056U, HII8056C, HII8056U, HII8046C, HII8046U,
HEI8046C, HEI8046U

Advertisement

Table of Contents
loading

Summary of Contents for Bosch HEI8056U

  • Page 1 Electric and Induction Ranges Installation Instructions Slide-In Ranges HEI8056C, HEI8056U, HEIP056C, HEIP056U, HIIP056C, HIIP056U, HII8056C, HII8056U, HII8046C, HII8046U, HEI8046C, HEI8046U...
  • Page 2: Table Of Contents

    Removing the Warming Drawer ..15 Replacing the Warming Drawer ..15 This Bosch Appliance is made by BSH Home Appliances Corporation...
  • Page 3: Safety Definitions

    9 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Safety Definitions 9 WARNING 9 WARNING This indicates that death or serious injuries may TIP OVER HAZARD! occur as a result of non-observance of this warning. A child or adult can tip the range over and be killed.
  • Page 4 9 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Safety Codes and Standards Important - Save these instructions for the local electrical inspector's use. This appliance complies with one or more of the following Before installing, turn power OFF at the service panel. Lock Standards: service panel to prevent power from being turned ON •...
  • Page 5: Preparation

    Preparation Carefully remove internal protective packaging taking care to secure any loose accessories and instruction manuals. Before You Begin Remove bracket(s) securing appliance to base pad, if present. Tools and Parts Needed The unit should stay on the packaging base until ready to be lifted into cabinet cutout.
  • Page 6: General Information

    ___ 3. Removing the oven door and warming drawer prior Verify that wiring to the house is adequate. Contact your to installation reduces the unit weight and makes local utility company to verify that the present electric the range easier to move. Additionally, the removal service to your home is adequate.
  • Page 7: Cabinet Requirements

    No clearance is required from unit walls to adjacent vertical combustible walls on rear, right or left. Install Ventilation Bosch strongly recommends the installation of a ventilation hood above this range. For most kitchens, a certified hood rating of not less than 300 CFM is recommended. The range hood must be installed according to instructions furnished with the hood.
  • Page 8: Prepare Walls And Floor

    Note: Some cabinet finishes cannot survive the temperatures allowed by safety standards, particularly self- cleaning ovens; the cabinets may discolor or stain. This is most noticeable with laminate cabinets. Flame retardant materials bear the mark: UNDERWRITERS LABORATORIES INC. CLASSIFIED MINERAL AND FIBER BOARDS SURFACE BURNING CHARACTERISTICS, followed by the flame spread and smoke ratings.
  • Page 9: Installation Procedure

    Electrical Connection Installation Procedure The range may be connected using an electric range cord (as specified in the Electrical Requirements section Installation of the Anti-Tip preceeding) or using a flexible conduit electrical connection. Bracket 9 WARNING 9 WARNING Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install A child or adult can tip the range an outlet near the appliance.
  • Page 10 Install Strain Relief 3-Wire Hookup 4-Wire Hookup Place strain relief in knockout below terminal block. 9 WARNING The strain relief provided with your range cord must be properly installed. Strain reliefs vary. Carefully read and follow the instructions included with your strain relief.
  • Page 11 4. Remove the green grounding screw from the lower end the unit may be connected to the power supply via a three- of the grounding strap. Remove the upper end of the wire connection. grounding strap from the center post of the junction bar.
  • Page 12: Connect Flexible Conduit

    Connect Flexible Conduit 3. Remove the top nut (has an attached locking washer) from each terminal post. The range can also be connected via flexible conduit. If using this method, always use the lugs supplied. Note: In Canada, the range is shipped from the factory with the range cord already installed.
  • Page 13: Complete The Installation

    9. Properly secure the flexible conduit at knockout on 7. Properly secure flexible conduit at knockout panel on angle and at supply side junction box. The wiring is range and at supply side junction box. The wiring is now complete. now complete.
  • Page 14 4. Measure the back left corner of the range to the bottom Slide Range into Opening of cooktop (B). Adjust leveling legs until this height is the same as the corner dimension. 9 CAUTION Unit is heavy and requires at least two persons or proper equipment to move.
  • Page 15: Removing The Oven Door

    To help avoid injury or Check Back of Range for Proper Installation damage be sure to read the above WARNING 1. The cooktop should rest lightly on the countertop. before attempting to 2. There should not be any gap between the countertop remove the oven door.
  • Page 16: Replacing The Oven Door

    Replacing the Oven Door 1. Holding the door firmly in both hands, grip it on either side, not by the handle. 2. Tilt the door back slightly towards you until it opens about 7" at the top. 3. Slide the hinges into the slots as far as they will go and then lower the door straight...
  • Page 17: Removing The Warming Drawer

    Removing the Warming Drawer 9 CAUTION To prevent burns, do not remove drawer while hot. Be sure the drawer is empty before removing. Removing Drawer from Housing NOTICE: The following is the manufacturer’s recommendations for removing and installing the drawer to minimize the risk of damage to the PTO mechanism.
  • Page 18 With the drawer removed, set the slide inner rail to the Notes drawer locked position by pushing the slide inner rail A slight side-to-side wiggle motion may be required ▯ toward the rear of the housing until it locks in place. to properly get the ball bearings to accurately align.
  • Page 19: Testing Operation

    5. If any of the tests do not result as explained above, contact Bosch service for assistance. Otherwise, continue with testing the rangetop burners. If any of the tests do not result as explained above, contact Bosch Service for assistance. Otherwise, the installation is complete at this time. English 17...

Table of Contents