Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BSi Manuals
  4. Locks
  5. R3-R8D
  6. Installation, programming, use

BSi R3-R8D Installation, Programming, Use

Smart deadbolt
Hide thumbs Also See for R3-R8D:

Advertisement

Quick Links

Download this manual
Smart Deadbolt
R3-R8D
Installation
Programming
Bluetooth Pairing

Advertisement

loading

Related Manuals for BSi R3-R8D

Summary of Contents for BSi R3-R8D

  • Page 1 Smart Deadbolt R3-R8D Installation Programming Bluetooth Pairing...

  • Page 2: Parts In The Box

    Parts in the box...
  • Page 3 Screws in the box...
  • Page 4 Check the door dimensions .Measure to confirm that the hole in □ the door is 2-1/8” (54 mm) .Measure to confirm that backset is □ either 2-3/8 or 2-3/4” (60 or 70 mm)
  • Page 5 Measure to confirm that the hole in □ ..the door edge is 1” (25 mm). Measure to confirm that the door is □ ..from 1-3/8” (35 mm) to 2-1/8” ..(55 mm) thick.

  • Page 6: Prepare Tools

    Prepare Tools Additional Tools Only for door thickness ≤ 1-3/4” (45 mm), not needed for door thickness > 1-3/4” (45 mm) △ ！ Use a screwdriver to install the lock. △ ！ Don’t use power tools to install the ..lock, only use power tools to drill ..the necessary holes.
  • Page 7 Remove Existing Lock Remove the entire deadbolt, including the bolt. Also, remove the strike box from door frame.

  • Page 8: Installation View

    Installation View...
  • Page 9 □ 1 .Check the Door Backset...
  • Page 10 □ 2 .Drill a Hole for the Door Sensor Place the fixture plate on the original □ latch screw holes of the door. As for different door’s.backset 2-3/8”, or 2-3/4”, place the texture plate in different placement according to the diagram below.
  • Page 11 Drill a hole for the latch sensor. □ Follow the diagram below for drilling hole’s direction according to different door’s backset. 2-3/8” (60 mm) 2-3/4” (70 mm)
  • Page 12 Remove the fixture plate after the □ hole is drilled.
  • Page 13 □ 3 .Install the Deadbolt Door’s backset 2-3/8” (60 mm) □ ..Make sure the slot in the bolt is /centered in the hole, “UP” is facing ..upward, sensor on the top side.
  • Page 14 Door’s backset 2-3/4” (70 mm) □ ..Hold the faceplate and twist the ..body to extend the latch from 60 mm to fit door’s backset 70 mm. Backset 2-3/8 (60 mm) Twist the body. Backset 2-3/4 (70 mm)
  • Page 15 Make sure the slot in the bolt is □ centered in the hole, “UP” is facing upward, sensor on the bottom side.
  • Page 16 Install the deadbolt with screw A. □...
  • Page 17 .Use a screwdriver to test that the □ deadbolt extends and retracts .smoothly in both directions. .Keep deadbolt retracted (unlocked) .after testing. UNLOCKED...
  • Page 18 □ 4 .Install the Strike Box Place the fixture plate on original □ holes of strike box of the door frame. As for different door’s.backset 2-3/8”, or 2-3/4”, place the texture plate in different placement according to the diagram below. .Use screw A to fix the plate.
  • Page 19 Drill a hole for magnet of strike box. □ Follow the diagram below for drilling hole’s direction according to different door’s backset. 2-3/8” (60 mm) 2-3/4” (70 mm)
  • Page 20 Remove the fixture plate after the □ hole is drilled.
  • Page 21 Install the strike and strike box. □ Strike & Strike Box direction 2-3/8” (60 mm) 2-3/4” (70 mm)
  • Page 22 .Use screw A for installation. □...
  • Page 23 □ 5 .Assemble the Exterior Assembly and Cylinder Before installation, ccompare the tailpiece length to the door .thickness. Trim the tailpiece .length according to the picture .below if the door thickness less than 1-3/4” (45 mm). .If the door thickness is more than .1-3/4”...
  • Page 24 Insert cylinder into touch screen. □ “KevLok” on the cylinder is on top. Screw cylinder pins into cylinder. □...
  • Page 25 Adjust the tailpiece direction. □ Make sure the painted edge of tailpiece facing in the same direction as the latch bolt. Painting Latch bolt...
  • Page 26 Make sure the latch is fully retracted □ .Both cables go underneath the latch. Align the tailpiece through the slot in the latch, painted edge face to the .latch bolt direction. retracted...

  • Page 27: Install The Mounting Plate

    □ 6 .Install the Mounting Plate Tailpiece and cables go through □ .the mounting plate. Tighten screws B & C. Screw B is to □ be placed one of holes close to the .latch bolt.side.
  • Page 28 Use a key to test locking and □ ..unlocking works smoothly. .Secure the mounting plate with □ .screw A. Make sure the outside .touchscreen is straight before .tightening screws. Keep parallel to door edge.
  • Page 29 □ 7 .Install the Interior Assembly Remove battery cover. Do not load □ .batteries until the lock is completely installed. .Connect cables to the interior □ assembly. Make sure cables ”click” into place. Tuck cables inside the space of the door.
  • Page 30 .Adjust the thumb turn position □ .either vertically or horizontally .depending on deadbolt orientation. .Tailpiece must be horizontal. Align the tailpiece with the spindle of □ .interior assembly.
  • Page 31 Make sure the tailpiece in horizontal □ .position, thumb turn position as step C likewise, and deadbolt is retracted. Test operation using a key .and thumb turn for rotation. Secure with screws D, use hex key □ .wrench to fix hex screw E.
  • Page 32 □ 8 .Perform the Door Handing Process △ ！ This step will teach the lock which side of the door it is on, crucial for the lock to operate properly according to the door orientation. Leave latch bolt UNLOCKED and □...
  • Page 33 Load 3 pcs AA batteries, press and □ hold vacation-mode button. Vacation-mode button △ ！ For the best results, use new, non-rechargeable Alkaline batteries. Continue pressing vacation-mode □ .button. Load the last battery and .release vacation-mode button when You hear the elody. The bolt will extend and retract.
  • Page 34 Turn the thumb turn to extend the □ bolt, and then press quick-unlock button to retract the bolt. .If it works in order, the lock is .functioning properly. Quick-Unlock Button...
  • Page 35 Two Administration Modes EZ mode 1. ONE user code is available. 2. One-time user code is not available. 3. Keypad sound cannot be turned off. Normal mode 1. Maximum 200 user codes. 2. One one-time code is available. 3. Keypad sound can be turned off. △...
  • Page 36 Bluetooth paired button Reset button...
  • Page 37 Programming & Setting Master Code (4 to 6 digits) .Remove one of batteries, press and □ hold the Reset button. △ ！ Only use non-rechargeable j.AA ALKALINE batteries. .Load the last battery and keep □ holding the reset button, do not .release it until you hear a melody.

  • Page 38: Unlock The Door

    △ ！ When you perform the above steps ..programming and setting the .jmaster code, please do it before .,backlit goes off, if you enter ..numbers or symbols after backlit goes off, please restart the ..programming process. Unlock the door .Extend the bolt using the inside □...
  • Page 39 Set up your smartphone with KevLok APP .Download KevLok app from □ .the App Store, or Google Play. Remove one of batteries, press and □ hold the Bluetooth button. △ ！ Only use non-rechargeable j.AA ALKALINE batteries. Load the last battery and release □...
  • Page 40 Tap the green lock icon. □ Press Bluetooth button on lock □ .device for 3-5 seconds. Release Bluetooth button, go to □ .KevLok app, it will show “Paired”, .then press “OK”. Tap the green lock icon. □ Tap lock icon to unlock the lock. □...
  • Page 41 KevLok Function For a demonstration video of Bluetooth pairing, and each function of the KevLok, please scan the QR code, the videos are under “Manual” tab. There is an index underneath the video for each of the KevLok function, you can connect the timeline link to find the specific functions you need.

  • Page 42: System Reset

    System Reset Resetting your lock will restore your lock to factory settings, and delete all user codes, including the master code. If you wish to perform a system reset, follow the same steps as Programming & Setting Master Code. KevLok App Reset Resetting the KevLok App will erase pairing setting, and other distributed smart keys.

  • Page 43: Fcc Statement

    FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 44 Smart Deadbolt R3-R8D Installation Programming Bluetooth Pairing...