Page 1
This appliance must be installed, maintained and removed only by an Authorised Person. For continued safety of this appliance it must be installed and maintained in accordance with the manufacturers instructions. Brivis Inverter Icebox Installation Manual This appliance must be installed in accordance with: •...
“Should” indicates a recommended requirement of this manual Deviation from these instructions, may at the discretion of Brivis, void the warranty. As a result, the homeowner and or installer may be charged a fee for non-product warranty related call outs. Also note that failure to comply with these instructions may preclude Brivis from being able to service the appliance.
Failure to do so may prevent the correct operation of the unit 1.4 Codes / Regulations Brivis ICE units must be installed, serviced or repaired in accordance with these instructions and related regulations, codes, standards, and authorities. These include but may not be limited to: •...
2.2 Icebox Supply & Return Air Side The 10kW Icebox model is available in left hand orientation (DINIB10Z7-L) and right hand orientation (DINIB10Z7-R). The 13kW and 15kW Icebox is available in left hand orientation from factory with the capability of being converted to right hand orientation. Diagram 3: Icebox Supply &...
Check to confirm the holding charge. For lifting details refer to the General Arrangement drawings. Note: Brivis Inverter ICE is not designed for installation on a marine craft, houseboat, or any similar environment.
3.3 Flashing Kit All ductwork shall be adequately weather protected by a flashing kit designed for a 10kW, 13kW or 15kW Icebox. The flashing kit is available in two sizes, 150mm and 250mm, each containing four parts. Diagram 7: Flashing Kit Item Description Quantity...
• 24 volt control wiring shall be installed from the Icebox electric box (Terminals A1, A2) to the Heater (StarPro series) or to Brivis Thermostat as required. • The electric box has standard 10A power cord and plug, please do not cut or modify the cord.
4.3 Condensate Drain All Icebox models have a 3/4” BSPM thread protruding from the bottom of the cabinet to facilitate connection to a drain. • A non-flexible drainpipe shall be installed for condensate run-off with a continuous downward grade away from the unit of not less than 1:50. •...
4.6 Flashing & Wiring Installation Diagram 11: Left and Right hand flashing 1. Position the Icebox on hard level base in front of wall penetration and Flashing secure supply and return air duct. Right Hand 2. Remove screws from the Icebox as shown, three each side.
Page 13
This cable is field supplied and shall access the Icebox through a grommet located beneath the flashings on the return air side, refer to Diagram 13. Run the cables under the flashing; do not drill any holes in the flashing for cable access. Diagram 13: Wiring into the Icebox 2-Core Cable to: BX5 - Heater PCB (refer Diagram 19)
Page 14
Diagram 15: 3-Core shielded communication cable between indoor and outdoor units...
Page 15
Diagram 16: Wiring at the Icebox PCB Note: For installation requirements of the outdoor condenser refer to the installation manual supplied with it.
4.7 Mounting and secure the Heater Diagram 17: Securing heater support bracket 1. Remove the two screws positioned in top corner of the heater (item 1), building side. 2. Secure the ‘Heater Support Bracket” to the heater with screws removed in the above step.
Heater cabinet wall Grommet Icebox PCB relay connections 24VAC Brivis Networker Diagram 20: BX3 Wiring circuit for HCDSI24 to Icebox and Brivis Programmable Thermostat Add-On connections (A1 & A2) at Brivis Programmable For connection refer to installation instruction Thermostat and CDU for supplied with “B063033...
5.0 SYSTEM AND DUCTWORK DESIGN Good duct design and sizing are essential to every Brivis ICE cooling system. Use the Brivis “SuperSizeGuide” / Brivisize, Technical Data Sheets or HB276. In general: Ductwork should be airtight and have a minimum insulation rating of R1.0 •...
7.0 SPECIFICATIONS Capacities tested in accordance with AS/NZS3823.3. Due to our policy of continuous improvement specifications are subject to change without notice. For details on the condenser unit, please refer to the Brivis ICE Inverter - Technical Specifications page.
Page 20
Help Line. innai recommends that this appliance be serviced every 2 years. With our policy of continuous improvement, we reserve the right to change, or discontinue at any time, specifications or designs without notice. B062742 Brivis Inverter Icebox IM Issue E October 2019...